Search Documents

In recent years, Computational Fluid Dynamics, CFD, has been commonly utilized in the mining industry to model the fluid flow behavior in underground mine workings. This paper uses CFD modeling to simulate the airflow behavior in underground crosscut regions, where brattice sails are used to direct the airflow into these regions. Brattice sails are cost effective ventilation control devices for temporary or permanent use in underground mining. They can be used to deflect air into the unventilated areas such as crosscut regions. Their design and installation is a fundamental issue for maintaining a sufficient supply of fresh air and achieving effective air circulation and contaminant removal. At the same time, they should have little impact on the mine ventilation system. This paper presents the results of a two-dimensional CFD model, which examines the effects of brattice length on fluid flow behavior in the crosscut regions. The results of this study will assist in understanding the ventilation air behavior and in determining the optimum size of brattice curtain (sails), which provide a highly effective contaminant removal from the unventilated mine areas. This, in turn, helps the mine ventilation designers to meet the mine safety requirements.

Jan 1, 2009

ICMM’s vision is ‘a viable mining, minerals and metals industry that is widely recognised as essential for modern living and a key contributor to sustainable development’. The ICMM Sustainable Development Framework provides the basis for achieving this vision by assisting the industry to improve its performance. Two years on from the first SDIMI conference, significant progress has been made in further developing and implementing the Framework. To fulfill their commitment to implement and report performance against the ten sustainable development principles in the Framework, ICMM’s corporate members have committed to report ‘in accordance’ with the GRI 2002 Sustainability Reporting Guidelines and the Mining and Metals Sector Supplement, developed by the GRI and ICMM. While much remains to be done, development of the Supplement and the commitment to reporting mark an important milestone for ICMM and the sector.

Jan 1, 2005

By J. Patrick Powers, Arthur B. Corwin

Modern improvements in hydrogeology make it possible to predict with good reliability the performance and cost of ground water pumping systems in many tunneling situations. The testing and analysis techniques are presented. Data from the Buffalo NY LRRTS (1978-1980) illustrate the successful application of the technique for tunneling in rock. Data from the Red Hook Interceptor Tunnel in Brooklyn NY (1978) illustrate the application in soft ground. The Red Hook project also illustrates concerns for the side effects from dewatering, such as ground settlement and damage to timber structures. At Red Hook protective measures included compressed air, artificial recharge and controlled dewatering. Given the uncertainties of the underground, the possibility of unexpected situations must be considered. A hard rock sewer tunnel in Atlanta, Georgia (1982) illustrates an unexpected problem, and the emergency measures used to solve it.

Jan 1, 1985

By Klaus Schönert, Martin Botsch

In common high intensity magnetic separators, the magnetic particles are deposited on ferromagnetic matrices, such as expanded metals, steel balls or grooved plates, inserted into a strong magnetic field. The nonmagnetic material is flushed through the matrix chamber. Discharging the magnetic particles is only possible if the magnetic field is reduced to zero (e.g. high gradient magnetic filtration for the purifying of kaolin) or the matrix chamber is moved out of the field by a rotor (e.g. the Jones Separator). Therefore, these separators perform only in a batch or semicontinuous mode. A real continuous operation requirs transport of the deposited magnetic material to an outlet where it can leave the separation chamber inside the field. One possibility for accomplishing such separation and transport is through the use of a rotating induction body with a certain shape, such as a spiral.

Jan 1, 1995

By Y. J. Wang

The use of controlled recirculation began in the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually, and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a nondimensional parameter (A), which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, far and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of and the subsystem air quantity. Numerical examples are included.

Jan 1, 1997

By P. Somasundaran

Beneficiation by froth flotation, which exploits the difference in surface properties of minerals, has been a promising method for coal cleaning. However, dissolved mineral species present in coal flotation systems can interact with particles and other species leading to drastic effects on flotation. Particularly, precipitation or adsorption of such species on the particles can alter their surface properties and thus influence the efficiency of coal cleaning. In this work, the bulk and surface precipitation of the dissolved mineral species present in Pittsburgh No. 8 coal was investigated under controlled experimental conditions. Changes in the surface properties of coal due to the precipitation were monitored by following zeta potential. Solution potential data were used to elucidate the mechanism of the precipitation. The effect of the precipitation of the dissolved species on the floatability of coal was found to be marked.

Jan 1, 1995

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By J. Drelich, J. Pletka

Lost foam casting is a process in which a polymeric material is formed into the shape of the part to be cast. Parts that are more complex are fabricated by simply gluing several patterns together. The pattern is then coated with a refractory material consisting of a mineral mixture and binders. Finally, hot metal is poured into the pattern, evaporating the expanded polystyrene and taking the shape of the coating shell. Prior to casting, a significant number of the patterns are damaged and inevitably landfilled. In this study, a process was developed for the recovery of expanded polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and pneumatic separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene. Key words: Casting, Lost foam process, Expanded polystyrene recovery

Jan 1, 2003

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By Jeff Schwoebel, Arcy, D&apos Horner

The Deep Coal Seam Project is a multi- year, large-scale research and development effort between the Gas Research Institute (GRI) and Resource Enterprises, Inc. (REI). The project is being conducted at the Red Mountain Site, a multi-well test site located in the southeastern portion of the Piceance Basin near Collbran in Mesa County, Colorado. The project objective is to develop the drilling, reservoir evaluation, completion and production technology required to produce gas from a thick, deeply buried coal seam. To understand the parameters controlling gas production, project efforts are focused on the Cameo "D" coal reservoir which lies at a depth of about 1707 m (5,600 ft) at the test site. This paper overviews the drilling, testing, completion, and production techniques used on the 1, 2 and 3 Deep Seam wells and implications for resource development.

Jan 1, 1987

By J. A. King, D. R. Weir, P. C. Robinson

The complex mineralogy of the Porgera resource has a pronounced effect on process selection for the recovery of refractory gold and silver. Intimate association of gold with pyrite necessitates a high degree of sulphur preoxidation to achieve acceptable levels of gold recovery. Acid pressure oxidation has been demonstrated to be the only commercially proven process capable of achieving the required level of pyrite oxidation. Gangue mineralization dictates preconcentration of the sulphides to limit the acid consuming capacity and carbon dioxide generation during oxidation. However, the relationship between concentrate sulphur grade and gold recovery to concentrate ultimately governs the optimum degree of sulphide preconcentration. Minipiloting of the preconcentration and oxidation stages of the Porgera flowsheet are described. The influence of these processes on subsequent recovery of precious metals together with the technical and economic necessity of concentrate pretreatment prior to oxidation are discussed.

Jan 1, 1987

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By David M. Stearns

Introduction Millions of tons of coal are shipped by rail each year in the US. Loading those trains efficiently is a topic being studied by coal producers and railroads. Alternatives range from volumetric loadouts to systems that weigh the product, using either belt conveyor scales, track scales, or weighbins. Each system has its proper application and each has pros and cons, depending on the volume, nature, and layout of the specific loading facility. In recent years, a batch weighing system has been developed that offers significant benefits to higher volume operations shipping by a unit train. The Unitrain Loadout System (ULS) features a precision electronic batch weighing system married to a mechanical loadout system by a microprocessor-based digital control system. A batch weighing loadout could be designed using analog electronics or even a mechanical weighbin. But it is the adaption and use of a microprocessor that provides the primary benefits of a unit train loading facility. Those benefits are accurate weight determination, optimum car use, overload prevention, speed in loading, optimum labor use, and documentation of the loading process. Unitrain History The first ULS was erected for iron ore applications in Canada during the 1960s. The first domestic system on coal was installed at Pittsburg and Midway Coal Co.'s McKinley mine at Gallup, NM, in 1978. At present, there are more than 20 Unitrain Loadout Systems in operation worldwide. They are loading minerals, concentrates, and coal. Eleven systems are presently in service or under construction in the US. In the last several years, a number of comparable systems have also been installed. As a result, the concept has been well proven and is now commercially available from several sources. Unitrain Operation The basic operation of a ULS involves loading a unit train with individually weighed batches of coal while it moves slowly under a loadout tower. Typical coal systems are designed to load at rates of 2.7 to 6.3 kt/h (3000 to 7000 stph). The contents of each car can be accurately weighed. This meets the requirements of the National Bureau of Standards Handbook No. 44 for static weighing. Also, cars can be loaded within very close tolerances. This optimizes railcar usage and prevents overloads. Principal components of the loadout system are the main feed conveyor, the surge bin, surge bin gates, weighbin, weighbin gate, flood loading chute, control room, calibration weights, and hydraulic and electrical systems (Fig. 1). Main feed conveyor: Coal is delivered from a storage area by the main feed conveyor. The conveyor fills the surge bin. It should be capable of conveying coal at the same rate at which it is being loaded. Usually the feed conveyor is equipped with a conveyor scale that can display rate in the control room and control feed to the belt. The surge bin will typically store 227 to 272 t (250 to 300 st) of coal. If the loadout is installed in an over-the-track silo, there is no need for a surge bin. Four double-bladed, hydraulically actuated gates are incorporated into the bottom of the surge bin. These gates open to fill the weighbin. Automatic pre-act points are selected by the control system. They shut these gates as the desired weight is approached. The final amount of coal is added by a single gate that closes. This results in a weighed batch of coal within ± 0.5% of the selected optimum load per railcar. Thus, if loading 91-t (100-st) capacity cars, the system is set to batch up 90.2 t (99.5 st) batches. Each car is expected to be loaded between 90 and 91 t (99 and 100 st). Weighbin: The weighbin is next in the flow scheme. Typically, it is

Jan 3, 1985

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By M. C. Stuttle

MDL Rock Lasers has undertaken successful mapping trials of abandoned mine workings using its underground cavity scanning system. The work was being performed for Kalgoorlie Consolidated Gold Mines (KCGM), Australia's largest gold producer. MDL Rock Lasers supplies underground surveying systems to the mining and quarrying industry KCGM's Fimiston Super Pit, located in Kalgoorlie, Western Australia, is Australia's largest open-pit gold operation. Fimiston's final pit design is expected to be 3.7 km (2.3 miles) long, 1.5 km (0.9-miles ) wide and 540 m (1,770 ft) deep. During the early days of Australian mining, underground operations were labor intensive. Mining was selective and generally narrow stopes were mostly backfilled. Improved processing technology and mine mechanization during the 1970s and 1980s has permitted larger scale operations to adopt less selective underground-stope operations. The "super pit" concept was a logical step for mining companies working toward economies of scale. However, the industry recognized that there was no precedent for excavating a 500-m- (1,640-ft-) deep open pit through ground previously affected by old workings. To appreciate the geotechnical challenge facing KCGM, it is necessary to consider that under the pro¬posed area at the open pit, stoping reached a level of 1 km (0.6 miles) and was supported by more than 2,000 km (1,240 miles) of development headings. The company was fortunate because plans were available for the Golden Mile underground operations. The existing plans were interpreted by the mine's geotechnical team and computer models were constructed of the underground workings. These models can be imported into three-dimensional mine planning packages, such as the Vulcan's Unix-based software, Envisage, to assist analysis and design. This prior knowledge of the workings provided the focus for investigating and confirming ground conditions using probe drilling. After several iterations of drilling, followed by detailed analysis, several decisions were made relating to the nature of the ground and the mining approach to be taken. It was recognized that the stope models were not perfect due to hu¬man error, lack of original survey information and progressive deterioration in ground conditions. It also became apparent that the sole reliance on probe drilling was inefficient in terms of time and quality of information. This was particularly true in complex areas where stopes are in close proximity. A major concern was the presence of open stopes (voids). In many cases, stopes consist of combinations of filled and void sections. The condition of pillars within these underground workings is extremely important. In time, pillars collapse and voids will propagate in upward and lateral directions. So systems needed to be developed that allowed rapid and accurate verification of ground conditions. KCGM was introduced to MDL Rock Lasers while investigating technology for underground mining. The two companies decided to use the C-ALS, MDL Rock Laser's underground laser, cavity scanning system, to improve the management of mining through affected ground. This system was to be used in conjunction with probe drilling and void mapping activities. A field test in one area of the Fimiston Mine verified the capability of the C-ALS system to quickly and efficiently assist in this decision making process. The C-ALS scanner features lightweight, carbon fi¬ber alignment rods from Measurement Devices Ltd.'s (MDL) Boretrak MKII. This is a borehole deviation system that stops the two axis measurement head rotating and lowers the system down a borehole. The scanner is deployed by a 110-mm (4.3-in.) borehole, up, down or sideways. The operator can then carry out vertical and horizontal plan section scans at any user specified ARC (an angular increment of 2°) or the distance between two points on the ARC (CHORD) increments. Windows '95 software enables the operator to control the cavity scanner remotely, surveying the area in real time. The system makes data quick and convenient.

Jan 1, 1999

By Brian E. Davies, Bobby G. Wixson

INTRODUCTION The mining, extraction and refining of metals into useful materials is an honorable profession with an ancient and productive history. Civilizations have long depended upon metals for their implements, structures and machinery necessary for survival, growth, and development. Today, as in the future, metals and minerals are essential to the progress of mankind as we approach the 21st century with technologies and concepts that will require new concepts and production from the metal mining and processing industries. Today is the tomorrow we talked about yesterday and the implementation of new ideas is essential if we are to achieve "Frontier Technology in Mineral Processing". Unfortunately, the state-of-the-art mining, processing, smelting and refining methods historically employed were less than desirable environmentally, which has caused todays public to view the metal mining and processing industry with concern. Presently the ancient rock and chat tips connected with old Roman lead-zinc mines which were worked in Wales are causing stream contamination problems that must be corrected at considerable expense to the local governmental agencies (Firth, J.N.M., et al., 1981). However, improved progress has been made and the environmental control and clean-up procedures utilized by modern lead-zinc operations in the "Viburnum Trend" or "New Lead Belt" of South East Missouri may serve as a model to illustrate how alternative technologies, environmental concerns and cooperative efforts contribute to efficient mineral production within the confines of a U.S. National Forest region without significant environmental impacts. This area received international attention when it was opened within the boundaries of the Clark National Forest in the mid 1960's. By 1970 it ranked first in the world by producing 432,576 short tons of lead ore and has since continued in this position producing 451,153 short tons of lead ore in 1983 representing 91% of the total United States lead production (U.S. Bureau of idines, 1983). This production comes from a mining area approximately 40 miles long by 10 miles wide extending in a north-south direction. Geologically the lead is disseminated throughout the Cambrain age Bonneterre Formation, mostly a dolomite, at depths ranging from 700 to 1200 ft. (213.4 to 365.8 m). Galena (lead) is the principal ore mined with lesser quantities of sphalerite (zinc), chaleopyrite (copper) and silver being recovered as economic co-products. This new mining development in one of Missouri is most scenic areas could have led to a classic confrontation between industries and environmentalists. Instead, through the cooperation of industries, governmental agencies and university researchers, the Ozark environment has been protected, and may serve as a model for future coexistence of the mineral industry with the environment. Cooperative Program Development As early as 1965 five new mines and two lead smelters were being prepared for production and environmental concern was an essential part of that planning. All the mining companies became acquainted with representatives of the various federal and state agencies and scientists from the University of Missouri-Rolla (UMR). During the next six years, St. Joe Minerals Corporation, American Metal Climax, Inc., Cominco American Incorporated, Ozark Lead Company (Kennecott) and American Smelting and Refining Company participated in cooperative research efforts. The companies also participated in information exchange meetings, the development of improved analytical methods and the utilization of research findings in the modification or construction of pollution-abatement facilities. Early on research was carried out to determine background values and to establish natural baselines of trace metals in the surrounding environment. The unusual topography and drainage pattern of the mining area were helpful since it was possible to establish control sites and test sites below individual mine-mill operations to study waste-water effects on the receiving streams. The location of the ‘New Lead Belt', mines, mills,

Jan 1, 1985

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the long wall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a long wall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

Jan 1, 1999

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991