Search Documents

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By W. Linwood Haden

Fullers earth has been mined since about 1920 in southwest Georgia and the adjoining area of Florida. In 1935, the mineral was named "attapulgite" after the source of a sample near the town of Attapulgus, Decatur County, Georgia. Mining and processing of the clay was described in a 1930 publication1 at a time when petroleum refiners were the major users. In the years since then, the uses and users of attapulgite have multiplied, and both mining methods and processing methods have been changed to optimize the clay for the new uses. A comprehensive review of the properties and applications of attapulgite 2 has been published. Only a brief review will be given here to explain the properties being sought and to show how these properties are optimized by mining and processing practices.

Jan 1, 1972

By D. L. Leach

This report covers laboratory experiments simulating in situ copper recovery from primary sulfide ores in sulfuric acid systems pressurized with oxygen. Copper extraction and acid consumption data are correlated with temperature in the range 50-150°C and quenched pH in the range 0.25-2. Adverse changes in the chemical composition of the leach solution and the formation of gangue-mineral alteration products and secondary sulfides can severely limit the extraction of copper above 90°C. Keeping the pH below the self-buffered value of about 2 and the temperature below about 110°C produces the maximum extraction rates. Forcing the pH too low not only results in excessively high acid consumption but may also limit the extraction of copper at temperatures above 100°C.

Jan 1, 1975

By Willaim A. Berg

Vegetative stabilization can help meet the esthetic objections and pollution problems posed by mine wastes. However, mine wastes are often unfavorable growth media and special treatments and techniques are needed for plant establishment and continued growth. The establishment of vegetation on mine wastes was the subject of many papers presented at the International Symposium on Ecology and Revegetation of Drastically Disturbed Areas held at Pennsylvania State University on August 3-16, 1969. This paper is a summary of those papers presented at the symposium that dealt with the nutritional and physical aspects of plant establishment on a variety of mine wastes. The synopsis presented is a combination of excerpts from the abstracts, notes on the oral presentations, and rough drafts of some of the papers. The papers will eventually be published in the symposium proceedings.

Jan 1, 1970

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By Earl C. Herkenhoff

Editor's note: The subject of mining on the moon can generate a wide range of strongly held opinion, from those leaning toward the view that, ultimately, such activity is the destiny of mankind to those who believe that all suggestions for moon mining to date are unrealistic, wildly expensive and in the hands of people who 'know nothing.' MINING ENGINEERING herewith publishes some of the basic pros and cons on the subject of moon mining by writers who are among those holding strong views on the subject, with the hope that some of our readers may be interested in joining this debate. Every mineralogist and most mineral industry people were keenly interested in the examinations of the first moon rocks brought back by US astronauts in 1969. Suffice to say that the examinations revealed nothing exotic in the mineral makeup of the very limited rock samples. The rocks were generally of igneous type, dark-colored and contained some common, Earth-type minerals. There was, in Earth terms, above average TiO2 content, but they contained nothing of commercial significance by Earth standards. Therefore, interest in moon minerals rapidly faded. Years later, on Sunday, May 4, 1986, living in Reno, NV, this author was shocked to read a local newspaper article by the Dean of the Mackay School of Mines, University of Nevada, Reno, headlined, "Moon Mining Not Far Off." Considering that the announcement more or less coincided with a slump in our domestic mining industry, the immediate questions in a reader's mind

Jan 1, 1991

By M. Javier

Mining is an industry of experimentation throughout human history. Recently, societies are giving a clear message about mining because many projects are being rejected around the world. These refusals are a generational reaction to the activity of mining. In practice, it generates the perception that mining is using the same methodology without attending to the gradual initiation of conflicts. This is in spite of the best engineering and technology of the time that are put in place at the presentation of those mining projects. Some of these rejected projects are geographically distant from each other, but the communities? rejection occurred during many cases under similar characteristics. This concern shows that the current model of mining projects needs to be replaced with a new one: A new Design, one within which the socio-environmental values of this millennium are inherent. This paper describes Mining Project 101 to help the industry to set the highest and cleanest standards for mining. It also presents its aspects to sustainability and nature, which provides the principles and procedures for designing, planning, and operating mining projects with sensitivity to nature. It offers methods of diagnostic, remediation, and extraction while at the same time preventing and preserving a physical, chemical, and biological equilibrium of nature. This emerging process will be a step up from having a mining industry unaccountable to the socio-environmental conflicts it perpetrates and will abandon the ?cosmetic? repair on the caducity of traditional models in today?s practice. In conclusion, we have the opportunity to change this model. KEYWORDS: Equilibrium in Nature, Geomímic, Deproduction, mine design.

Feb 27, 2013

By D. Denton, L. Buckingham

The dry grinding and leaching circuits of the Barrick Gold’s new Roasting Facility at Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs. Crushing is a two stage process using gyratory and cone crusher. Ore is stockpiled and then reclaimed to two parallel dry grinding mills. The double rotator dry grinding mills include a drying chamber, coarse and fine compartments and utilize a gearless motor drive (GMD) or “wrap-around”. In-circuit product transfer is accomplished with air slides and bucket elevators. Finished product separation is performed by both static and dynamic classifiers with the final product captured in baghouses. Recycle of unfinished product utilizes cascade chutes. The final ground product reports to two 2000 ton roaster feed silos. The two-stage oxygen flu-solids roasters with their associated gas train are the subject of a separate paper. The cyanide leach circuit is a standard carbon in leach system with circular swept screens for interstage carbon retention. The loaded carbon is sent to the existing Goldstrike autoclave plant for stripping and regeneration. Tails, after cyanide destruction, are deposited in the existing tailings dam with tails from the autoclave facility. Throughout the circuit, Clean Plant Design criteria were used to assure environmental compliance, ambiental acceptability and ensure worker health and safety. The commissioning and operation of the double rotator grinding technology has been very successful at Barrick Goldstrike.

Jan 1, 2001

By L. B. Paterson

Mining Engineers throughout the world have an appreciation for the importance of the role of the Blasthole Drill in one of the primary elements of the mining process. This paper highlights areas that could influence the overall cost effectiveness of that process of breaking rock and how equipment is designed and configured to meet that challenge. Factors influencing drill productivity and overall cost effectiveness are addressed, both in the Mine Environment and on the Blasthole Drill.

Jan 1, 1999

By K. F. Hollberg, D. Graehl, L. Despain

OCI Wyoming's recent expansion of its surface Soda Ash production facilities outstripped the mine's ability to supply Trona ore necessitating infrastructure changes to the mine. A computer simulation of the mine's production systems along with the surface facilities was created to determine the most economic investment alternatives to increase mine production. This paper describes the development of the simulation model; the results obtained, and discusses the issues involved in using simulation modeling for mine production system design.

Jan 1, 2002

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1997

THE FUTUREGEN CLEAN Coal project will be the recipient of $1 billion worth of federal stimulus money by way of the U.S. Department of Energy (DOE), which announced the commitment to the project. The money is expected to kick off years of further work that could finally see the project completed. One of the companies involved, Ameren Corp., said the $1.2 billion project ? which will include some private funding ? still has a number of hurdles to clear.

Jan 1, 2010

By Trevor R. Ellis

Minerals appraisers/valuers often find great difficulty in attempting to employ the sales comparison approach to the market value appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income-producing property. Here, common criticisms of the sales comparison approach by mineral appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the income approach are usually derived by minerals appraisers and by review of some conspicuous examples of the much-too-common misuse or abuse of the income approach in market value mineral appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables. The examples are used as the basis for a discussion of ways to employ adjustments for operating economics and many other factors, while warning against the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By E Marambio, R Brändle, G Fischer, G von Rickenbach, M Fuentealba, L Burgos, R Luis Fonseca

In underground excavations, under high stress conditions, ground support systems must provide safe and effective response to dynamic events. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the back analysis through numerical methods (central difference and Newmark’s method) of a ground support system tested with a double dynamic impact in 2019 is presented.

Apr 26, 2022

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

A thorough improvement in mine safety is contingent on many factors that require scientific decision-making for selection and prioritizing of important factors for safety improvement. Their analysis using an established scientific method can improve mines’ safety conditions and assist the administration for informed decision-making. This research establishes a mine safety evaluation index and proposes an integrative model based on the entropy weight and grey clustering methods. In the evaluation index, 27 significant factors of safety are identified and categorized into 7 criteria. The proposed evaluation system analyzes all indicators according to Pakistan’s current mine safety situation and their significance for potential safety improvement in the future. Results reveal that current safety practices are outdated due to a lack of mechanization in the mining industry and minimal capability of the management to achieve the desired safety targets. Appropriate safety policies and safety education are missing in the daily working environment. The lack of overseeing the execution of safety operations and the lack of ambition and strong work ethic workers contribute to the paucity of mines’ safety conditions. The prevention and control systems to manage risks and hazard are not in place, and the working environment in mines remain difficult. Therefore, to have enhanced mine safety, important factors can be addressed in chronological order, as presented in this paper. The proposed methodological approach can be applied to other prioritization applications to analyze the indicators and determine the appropriate management strategies.

Jun 14, 2021

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By Arash Nikvar‑Hassani, Timothy Batchler, Lianyang Zhang

Recently, a new hybrid geopolymer/biopolymer (GP/BP) cementitious material was developed for improving the performance of pumpable roof supports in underground mines. This study demonstrates the application of the hybrid GP/BP cementitious material and validates its effectiveness in full-scale. In this regard, eight (8) full-size (0.61 m diameter and 1.52 m height) cribs were produced in collaboration with Minova International Ltd and tested at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS) Laboratory. These full-size cribs were produced with different material configurations to evaluate the effect of water to solid (W/S) ratio, Portland cement (PC) content, and BP dosage. The results demonstrated and validated the effectiveness of the hybrid GP/BP cementitious material in increasing the peak and residual bearing capacities of pumpable cribs and eliminating the issue of deterioration when exposed to air compared with the conventional Portland cement/fly ash (PC/FA) cementitious material currently used in practice. On average, the peak uniaxial compressive strength (UCS) and the highest residual UCS after peak of the full-size cribs produced from the hybrid GP/BP cementitious material are 1.90 and 1.33 times of those of the PC/FA-based full-size cribs by one company and 2.32 and 1.66 times of those of the PC/FA based full-size cribs by the other company, respectively.

Feb 6, 2024

By Dan B. Kivari

One of the key operations in any milling circuit is grinding. Over the last two decades, large diameter Semi-Autogenous Grinding (SAG) mills have become the preferred primary grinding mills. The drive systems became more complex as the size of the mills became larger, during which time operating and design experience for SAG mill accumulated. Considerable reliance is now placed in power electronics to provide flexibility in SAG mill operation to meet the demands of lower operating costs. Whereas earlier most SAG mills were designed to operate at fixed speeds, present day SAG mills can operate at a fixed speed or variable speed through the use of an AC synchronous motor or DC motor. However, this flexibility comes with an increase in capital and operating costs. Since the capital and operating costs of a project directly affect the project's rate of return, the selection of a SAG mill and its drive system should depend, in part, on the impact that the extra cost makes on the project. This impact can be measured by performing an economic analysis based on Net Present Cost (NPC) calculations. Although the NPC calculation is an important factor in the grinding mill selection, other factors such as reliability of mill drives and power source are important elements in the decision making process. This paper examines how the NPC calculation, plus reliability and power source, influence SAG mill selection.

Jan 1, 1991

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011