Search Documents

By P. T. Brown

Denison Mines Limited, Canada's largest uranium producer located in Northern Ontario recently embarked upon an extensive development program that would allow them to substantially increase production and also meet the more stringent air quality standards established by the ministry of Natural Resources. To proceed with this program it was essential that the fresh air supply be greatly increased to the underground workings. A major portion of the mining area is located under Quirke Lake on the north limb of a syncline termed the Quirke Lake trough. The Denison engineers determined the most practical size and location for a proposed new fresh air shaft, eventually deciding to drive a 25 foot diameter shaft, 490 square feet in section for 1,800 feet long vertically. The shaft collar would be located on Roman Island, an island in Quirke Lake. A test hole was drilled from Roman Island to determine the ground through which the ventilation shaft would pass. This drill hole confirmed the location of the Quirke Lake over-thrust fault, a highly fractured water bearing zone 165 feet thick, approximately 800 feet below surface. Plans were made by Denison Mines Limited to seal and consolidate this ground when it was encountered by the shaft.

Jan 1, 1974

By G. W. Luxbacher

Acid rain legislation included in the Clean Air Act Amendments of 1990 caused a great deal of uncertainty regarding the price, source and production quantities of coal supplied to the eastern coal market. Powder River Basin and other western coals continue a rapidly accelerating migration eastward. South American coals move into the northern markets. States are proposing legislation to assist utilities in complying with the new regulations in hopes of maintaining their own coal industries. Some utilities question the long-term availability of eastern compliance coal. Major coal producers must make decisions now to assure their continuing presence in the market place. Several companies have adopted a strategy to acquire eastern compliance reserves, while others have invested in technology to compete as a low-cost producer. Legislation "Acid rain." This is a topic that was debated within the scientific, environmental and industrial communities for years. Those discussions resulted in a large outlay for the federal National Acid Precipitation Assessment Project (NAPAP), which was then ignored. Acid rain then became the subject of a "60 Minutes" broadcast that debunked the acid rain theory, supporting the NAPAP study conclusions. In the final outcome, however, acid rain was the driver for the Clean Air Act Amendments of 1990.

Jan 1, 1992

By K. Koizumf, A. A. Cram, K. Whitchurch

The Expert Scheduling is a new, exciting method for scheduling underground and open-cut coal mines. A key feature of the Expert Scheduler is the adoption of an expert or artificial intelligence system. The expert system makes decisions regarding the schedule, such as which area should be mined. With existing scheduling systems these choices are made by the scheduling engineer. Developing one area may be better than another if it offers better quality or lower costs. Information the engineer considers in these decisions could be; • coal tonnage and quality targets, • equipment utilisation, • mining cost, • and other practical constraints. In expert scheduling a number of experts are appointed to make these decisions. A number of mining strategies are examined for each period. Information for each strategy is evaluated by "experts" and the "best" solution adopted. The method is based on the Blackboard Techniques. With this technique information is presented to "knowledge sources” or "experts" by the Blackboard Controller for their "opinions". These "opinions" are examined by the Blackboard Controller to select the best strategy. Engineers can readily add experts to the system, and modify the weighting of experts to suit mining conditions. Using an Expert Scheduler means that many schedule op- tions can be analysed quickly with full repeatability.

Jan 1, 1996

By W. Jack Wilkes, Gilbert L. Butler

TRANSPORTATION TUNNELING The use of tunnels for transportation, namely rapid rail transit systems and highways is on the increase. How much that increase might be through the 1980's is the question that is discussed in this paper. In 1975, there were 218 route miles of subway tunnels for rapid rail transit and 154 lane-miles of highway tunnel. From the viewpoint of many transportation planners and designers, the tunnel is one of the tools which may be used to by-pass many types of obstacles: a mountain, a body of water, or a Central Business District (CBD). Therefore, the transportation tunnel is a rural as well as an urban solution with major emphasis on the latter because of the current transportation needs of our cities. In the case of rural locations, tunnels are usually constructed through mountains in order to eliminate miles of steep grades and dangerous curves, such as the Eisenhower Tunnel which cuts through the Continental Divide in Colorado along 1-70 and saves 10 miles and 40 minutes of driving time. Tunnels also provide an excellent transportation link across bodies of water in order not to interfere with shipping lanes. The Chesapeake Bay Tunnel and Bay Tubes of the BART system are excellent examples of this type of tunnel.

Jan 1, 1976

By Mohammad Irshad, Larry H. Heflin

INTRODUCTION The planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. is being designed and constructed by the Washington Metropolitan Area Transit Authority. At the present time, 112.6 kilometers (70 miles) of this system is in operation and contains 21 route-kilometers (13 miles) of rock tunneling, and 14.5 route-kilometers (9 miles) of soft ground tunneling. An additional 2.4 kilometers (1.5 miles) of single track tunnels in rock are planned and 6 additional contracts will consist of some 8 kilometers (5 miles) of twin tunnel, resulting in 16 additional linear kilometers (10 miles) of single track tunnel in soft ground. The Authority plans, upon its evaluation and the recommendation of the General Engineering Consultant, to include an alternative design incorporating the convergence confinement method of construction known as the New Austrian Tunneling Method (NATM), for Sections E-5, E-6e and E-8a of the E-Route. The Metro system is constructed in a variety of geological conditions and crosses the boundary of two major geographic provinces. Rock tunneling is to the west of this "fall-line" boundary, soft ground tunneling to the east. The soft ground tunneling portions of Metro construction lie in the coastal plain which consist of a

Jan 1, 1987

By L. John Minnick

Current developments in using lime and limestone slurries to remove sulfur oxide gases from the stacks of coal- and oil-burning furnaces have established an important need for treatment systems which include adequate disposal of resulting waste materials. The paper briefly outlines the classes of scrubbers which are using lime and limestone and describes the characteristics of the by-product material being produced. Some discussion is also included relating to methods of disposal of the scrubber underflow. Since coal-burning plants also produce fly ash as a waste material, one system developed by the author's company combines this material with the sulfur oxide by-products. The mixture is processed in a manner which converts the waste products into usable materials with acceptable structural and environmental properties. Recent interest in protection of ground waters from heavy-metal leachates has made the fly ash-sulfur oxide system an acceptable means of disposal, because the conversion products have very low permeability and adequately encapsulate soluble salts within the hardened mass. Although only limited information is available on the types and chemical requirements of limestone used in these processes, a few guidelines are presented to indicate the range of materials that can be used with good results.

Jan 1, 1974

By T. W. Healy, W. J. Trahar

INTRODUCTION The flotation of minerals from their ores in flotation cells involves understanding many chemical and physical processes ranging from electronic events in the bulk mineral and in the mineral surface regime. molecular events at interfaces, the statics and dynamics of thinning and rupture of microscopic to molecular intefacial films, the fluid mechanics of bubble- particle events, the dynamics of air-water-solid colloid states in a flotation machine, etc. etc. D.W. Fuerstenau, whom we honour in this symposium has made unique contributions to many of these diverse physico-chemical and technological sub-processes. The present paper is concerned with a number of observations of the behaviour of minerals in flotation cells and the surface science of some mineral sulfide-water systems. We do not intend to be comprehensive in our analysis, but rather to highlight the challenges that face the scientific masochist who chooses to understand "froth flotationn. In what follows, emphasis is placed quite deliberately on technologically relevant, dynamic or realistic flotation processes i.e. the recovery in a froth of a given sulfide mineral particle of a given size and history from synthetic or actual ores in a flotation cell. The paper also attempts to use the understanding that is emerging from the area of photoelectrochemistry of colloidal

Jan 1, 1989

By Ahmet Unal

Inexpensive and effective means of delivering courses to mining engineers who live at remote and scattered locations remains to be a challenging issue. Computer-based instructorless but interactive multimedia delivery is a good substitute to traditional short courses and one-way broadcasts. Such a system, enhanced with a wide area network, is an inexpensive alternative to two-way broadcasts and even to a traditional university. Course material can either be delivered on compact disks (CDs) or on-line from the host servers over the phone lines using a personal computer and a modem. Although technically not feasible using ordinary telephone service lines at the present time without further modification, advances in this field indicate that this up and coming medium may dominate the competition in the future. This paper investigates the present and the future of this technology and discusses the experiences gained in creating and disseminating a prototype multimedia CD which was created at the Rock Mechanics and Explosives Research Institute of the University of Missouri-Rolla to teach a portion of a course in Ground Control. The hardware and software used in creating the audio, 3-0 graphics, animation dips, video clips, and movies are listed. The structure of the program and the way how interactivity was achieved is explained in detail.

Jan 1, 1996

By Paul Sainato, J. Steven Gardner

Sustainable development is defined as ‘development that meets the needs of the present without compromising the ability of future generations to meet their own needs.’1 There has been considerable debate of late between environmentalists and mining operators concerning the current regulation and operation of mountaintop mining. To those not familiar with the practice, it essentially applies an area mining method to a mountaintop, removing all overburden above coal seams, resulting in full recovery of the resource with the excess or swell spoil material - (rock and dirt) being deposited in engineered fills in hollows to the side (known as hollow fills or valley fills - very similar to highway fills). Because most of the dialogue has been adversarial and mining’s response is perceived to be primarily reactive instead of proactive, a rift in communication and value systems between the two sides has widened. Since 1999, the global mining community has been concerned that there is a disconnect between mining practices and the values of today’s society.3 Working through the World Business Council for Sustainable Development (WBCSD), the International Institute for Environment and Development (IIED) was created to review mining practices in a project entitled Mining, Minerals and Sustainable Development (MMSD) driven by the following four goals:

Jan 1, 2005

By Barbara Maren Winkler

For mine production problems in mines with varying qualities, both open pit and underground, the linear programming method (LP) has been used successfully. By this method it is possible to keep the total production blend for each period within a required range of qualities while optimizing objectives like production costs, net return, ore grades, other qualities, or a combination of these. Technical restrictions like constrained capacities can be added to the model. This makes LP a flexible and powerful tool for mine production planning. Practical experiences have shown the major influence fix costs have on the actual economic result of a planning decision. It can be proven that fix costs cannot be included in LP models. We describe a way to address this fix cost problem by using mixed integer linear programming (MILP) as an extension to LP in the optimization of a mine planning problem. This raises the issue of complexity. We discuss the computational complexity of the resulting models and the enhancement of model flexibility for the user of a planning system. We demonstrate the method embedded in a practicable everyday planning system for a complex underground coal mine. By computational examples we show how the method improves the economical results of the planning.

Jan 1, 1996

By Michael E. Kelahan, Charles Y. Guan, Glenn A. Gruber

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By Y. C. Kim

One aspect of long-range mine planning in an open-pit mine is first to define the ultimate pit limit, i.e., the projected size and shape of the pit at the end of its life. This chapter is concerned with various techniques that are currently in use today in determining the ultimate pit limits using the computer. Prior to the early 1960's, open-pit limits analyses were entirely performed manually. This manual technique has been well explained by Soderberg and Rausch in Surface Mining (1968). Soderberg and Rausch also explain clearly the need for establishing the ultimate pit limits in long-range mine planning, i.e., location of surface facilities, dumps, etc. Consequently, the need for ultimate pit limit design will not be reiterated here. Nor will the definitions of the most commonly accepted terminologies such as break-even stripping ratio, economic cutoff grade, ultimate and working slope angles, preproduction stripping, etc. be repeated here. Briefly, the objective of the ultimate pit limit design (which is also frequently referred to as pit design in short) is to determine the projected final pit limits of an ore body and its associated projected grade and tonnage, which will maximize some prespecified economic criteria while satisfying practical operational requirements.

Jan 1, 1979

By Richard Hogg, Erol Kaya, Jan M. Mutmansky

Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research. The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, non- respirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.

Jan 1, 1993

By A. Peppas

Perlite is a naturally occurring siliceous rock, which can be expanded from four to twenty times its original volume when heated at a temperature close to its softening point. The expanded perlite is characterized by increased sound and thermal insulating properties. However, the conventionally expanded perlite products have high porosity and low mechanical properties that limit the range of their applications in the construction and chemical industry. The present work aims at the development of new closed porous microcellular material from perlite with enhanced mechanical and physical properties to be applied in new applications, like joint compounds, functional fillers for special paint types, special blasters and mortars, artificial marble. For the production of these new materials a vertical electrically heated furnace with six different heating zones and controlled gradient temperature profile was used. The effect of major process parameters, like temperature and air flow, on the quality of the produced materials was studied using Greek perlite from Milos Island. The quality of the new products was evaluated in terms of their bulk density, compression strength, water and oil absorption, surface area and pore volume. The experimental results show that the produced materials are characterised by improved mechanical and physical properties compared to the conventionally expanded perlite products.

Jan 1, 2006

By Gemei Yang, Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

Laboratory tests on controlled airflow recirculation have shown the development of transient states in response to changes in system prevailing conditions such as those generated by a sudden start-up and stoppage of fans. Researchers in many European countries have developed various models to explain these phenomena. However, these models failed to consider some important factors such as diffusion and dispersion of gas in turbulent flows. For both in-line and cross-cut recirculation, tests have shown that after the start- up of a booster fan, the gas concentration in the system fluctuates, reaching high levels at the initial states and slowly dying out with time. These fluctuations cannot be represented adequately by simple step-wise functions but rather by smooth, albeit complex equations. In this paper, the phenomena are explained by the convection-dispersion theory, and represented by a mathematical model. Based on a few simplifications and applying Fourier's Transform Method to the differential equations of the flow recirculation model, an integral form of gas concentration function was derived. The Simpson Integration Method was used to compute numerical results for two laboratory tests. The paper also discusses the range of the dispersion coefficient to improve the accuracy of the model.

Jan 1, 1989

By B. Andersen, P. Somasundaran

An accurate knowledge of the interactions among mineral particles and between such particles and dissolved and precipitated species is important in developing efficient separation processes. In this investigation, interactions relevant to dispersion and selective reagent adsorption (the two main prerequisites for selective flocculation) within Florida phosphatic clay Waste were studied. Initial studies with artificial slimes, consisting of pure clay and phosphate minerals, showed dispersion of artificial slimes to be relatively easy. The problems that were encountered during selective flocculation of the artificial slimes were due to unselective polyacrylic acid adsorption on clay, which was caused by the presence of multivalent calcium ions on the exchangeable cation positions on the clay surfaces. This problem could be solved by exchanging calcium for sodium, which reduces the interaction between the polymer and the clay surface. This procedure, however, was not successful for mineral mixtures. Natural slimes were found to be much more difficult to disperse. This was attributed to the presence of cementing materials such as humic substances and Al and Fe (hydr)oxide precipitates. Selective removal of these cementing materials resulted in good dispersion and partial separation. A further increase in the separation of natural slimes is most likely determined by the presence of calcium on the clay surfaces, as was found for the artificial mixtures.

Jan 1, 1994

By Severn P. Brown

Cement plants in the central Hudson River valley utilize limestones of the Helder-bergian Series of the Lower Devonian. Chiefly calcilutites, calcarenites, and cherty calcisiltites, these rocks represent progressively deeper environments, from lagoonal to neritic, with scattered reef deposits. Stratigraphic continuity is marked, and a layer-by- layer analysis shows strikingly constant chemical compositions. The structural picture varies from flat-lying and relatively unfaulted beds on the northwest, through gently folded and faulted beds on the north, to complex overturned beds with closely spaced imbricate faults on the south. Operating techniques are simpler in the north, where grade control is effected chiefly by the initial layout of the faces. In the south, grade control requires flexibility and frequent adjustment of faces or scheduling. A system of quarrying along strike has been developed, grade being computed from a cumulative foot-per cent graph of the critical oxides in each mappable layer. Balancing shovel production among the many faces is simplified by comparing production requirement ratios with ratios of the various types of rock in each face. Drilling and blasting limits are geologically controlled if warranted, or large blasts embracing several rock types are shot and the resulting pile of broken rock is staked along shovel limits.

Jan 1, 1966

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

By P. D. Roa, O. Noirot, H. Owens, D. E. Walsh, J. R. Mokka

Over a period of eight years (1989 through 1997) the Mineral Industry Research Laboratory (MIRL) at the University of Alaska, Fairbanks, AK, has investigated the effects of temperature, residence time and particle size on the degree of low-rank coal (LRC) upgrading for a nonevaporative, hydrothermal drying process, also known as hot water drying (HWD). The following three Alaskan LRCs were used in this study: Usibelli coal (Seam No. 4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10 to 20 min of residence time. Thereafter, the upgrading process slows down, and more than 100 min of additional residence time is required to produce percentage increases equivalent to what was achieved in the first 10 to 20 min. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove gindabilities all appear to change linearly with temperature within the 275°C to 325°C (525°F to 61 5 OF) range.

Jan 1, 2000

By Giin-Fa Fuh, Sally A. Shoop

An instrumentation program was developed based on the results of an analytical study of the geomechanical effects of longer longwall face lengths. Boundary element simulations showed that longer face lengths can cause in- creased face convergence and an increase in the shear stresses in the immediate roof. Empirical design methods predict that longer faces will cause little effect on abutment stresses as long as the roof caving is well behaved. On this basis, a longwall face instrumentation program was designed with emphasis on the interaction between face support and ground response for optimizing face conditions. At a 600-foot (183 m) face, five midface shields and two headgate shields were monitored with vary- ing hydraulic pump pressure. The instrumentation included six convergence rods with linear potentiometers to measure canopy-to-toe convergence; fourteen pressure transducers to monitor leg pressures; and two portable data loggers. Similar instrumentation will be in- stalled on a 750-foot (229 m) face for comparison. The results from the 600-foot (183 m) face indicate that a ground reaction curve, as determined from the relationship between the sup- port set pressure and the roof convergence, can be used to optimize the support pressure to control convergence, the key element to ground stability in the face area.

Jan 1, 1986