Search Documents

By J. E. deMasi

Over the past 12 years, Exxon Coal U.S.A., Inc. has shipped over 150 million tons of coal from two mines, Rawhide and Caballo, located in the Gillette, Wyoming, area. These mines are operated by The Carter Mining Company, a division of Exxon Coal. Shipments have moved to more than 25 electric utility plants in the west, midwest, southwest, and south. The customer plants have represented a wide variety of configurations, sizes. design criteria, emission standards, and operations in different parts of the country. We have learned a great deal about the performance of Gillette area coals in utility power plants during this period. This paper covers some of the highlights of Exxon's experience with these coals in customer plants. I will focus specifically on things mining engineers may be able to do to make the product better for the customer's use.

Jan 1, 1989

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989

By B. Cristol, G. Benier

Laboratory and pilot tests have shown that the grinding of some aluminas makes two populations appear : agglomerates’ and ultimate crystals’. Classical breakage functions (Size Mass Balance Method) aren't able to describe correctly this kind of grinding. So we have optimized a particular breakage matrix which takes into account the fact that the agglomerates can either be reduced in size or either be blown up to liberate the ultimate crystals. The models which were developed using this breakage matrix are in good agreement with the experimental results of the pilot tests. The industrial breakage functions were estimated from pilot breakage functions, using scale up prediction procedures and plant tests. The agreement between predicted and actual plant performance is excel1ent.A 20 % increase in capacity was predicted to be available by improving the grinding circuit classifier performances.

Jan 1, 1992

By Nora M. Hutt, Kevin A. Morin

One technique for controlling ongoing acidic drainage is to relocate and submerge net-acid-generating waste rock in a lake or water-retaining impoundment. This can lead to the overall improvement of water quality and the reduction In short-term environmental liabilities. A case study of this technique is the Eskay Creek Mine in northern British Columbia. Some findings of the study are: (1) the addition of lime to each truckload of rock, based on its rinse pH, neutralized the accumulated acidity and suppressed the accumulated-metal release, (2) only 10-20% of the dump's neutralization potential had been consumed when acidic drainage appeared, (3) water chemistry in the watershed recovered roughly three years after relocation, and (4) environmental liability was reduced due to the cessation of on-land acidic drainage with no degradation of lake chemistry.

Jan 1, 2000

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Y. J. Wang

In the, mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs. -quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1997

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By Jerzy Matuszewski

Under conditions of high methane content in the seams and the descending of exploitation to greater depths, methane hazard control is becoming more and more difficult. This is due both to the amount of methane released and to the technical possibilities of diluting and capturing it. The removal of excess methane from mine workings only by means of the ventilating current has become a problem. Therefore many countries designate large sums of money for research work in the field of controlling dangerous methane accumulations and for introducing this control into mining practice. In Poland the Central Mining Institute is leading in this field. Its Safety-in-Mines Institute, Barbara Experimental Mine in cooperation with collieries has recently carried out interesting investigations on the distribution of methane concentrations in gobs behind the front of longwalls mined with caving.

Jan 1, 1980

By Alec G. Richardson, S. H. Chiang, Ralph W. Lai, McMahan L. Gray

The potential of coal cleaning by selective agglomeration was examined for a Pittsburgh seam bituminous coal using isooctane as an agglomerating liquid. The effects of particle size, pH, degree of mixing, and dosage of isooctane on the pyrite and mineral matter removal from finely ground coals were investigated. The role of shear-enhanced-hydrophobic-association in the flocculation of fine particles was examined. The degree of liberation of pyrite from coal at different grinds was examined using an automated petrographic image analyzer. The effect of dispersant on slurry rheology during grinding was studied. The results indicate that over 95 percent of the pyritic sulfur can be removed from the coal. Final products containing less than 0.9 percent ash at a combustible recovery in excess of 90 percent have been obtained with multiple stages of cleaning.

Jan 1, 1989

By X. Shi, F. -Y. Wang

Automation and robotics are the keys to new intelligent autonomous mining systems that can remove operators from hazardous and stressful mining environments and provide the tools for greater productivity. This paper presents the components necessary for an Intelligent Task Control System (ITCS) for machine control in dynamic unstructured mining environments. In particular, the design details of a controller for an automated excavator are developed. The excavator controller uses fuzzy logic to interpret forces and torques gathered from a wrist mounted force/ torque sensor during the excavation process. This approach enables the transfer of human heuristics and expert knowledge to the controller. Several excavation tests using the fuzzy logic controller are described. These experimental results represent the first step toward an integrated approach that uses force/torque, vision and other sensor data to perform generic tasks in uncertain mining environments.

Jan 1, 1995

By J. W. Leonard, C. L. Jiang, B. K. Parekh, X. H. Wang

The selective depression of pyrite from the Kentucky No. 9 coal seam was systematically examined using various kinds of inorganic and organic chemicals. Most of the organic chemicals tested showed little selectivity in pyrite depression. It was found that both orthophosphate and pyrophosphate were effective for the selective depression of coal pyrite in coal flotation using fuel oil as a collector. At substantially low concentrations of pyrophosphate, the flotation of coal pyrite was completely depressed over a wide pH range, while the coal flotation remained unaffected. The mechanism of the selective depression of pyrite by phosphates was explained with the help of thermodynamic calculations of iron-phosphate-water systems and zeta-potential measurements. It was shown that pyrophosphate reacts strongly with the iron ions of pyrite to form stable hydrophilic iron pyrophosphate complexes on pyrite surfaces.

Jan 1, 1999

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By G. T. Adel

As a prerequisite to removing mineral matter from coal by any physical separation technique, the mineral and coal particles must be sufficiently liberated. In the case of the production of superclean (< 2% ash), low-sulfur products, the appropriate liberation size may be less than 10 µm. Unfortunately, much of the liberation data obtained at these fine sizes is only qualitative due to the lack of appropriate instrumentation. In the present work, computerized image analysis has been used to characterize several common eastern U.S. coals. In most cases, it has been found that micronizing of the coal is necessary in order to achieve sufficient liberation for deep cleaning. Liberation analyses of the products from the microbubble column flotation process have been used to distinguish problems in liberation from problems in selectivity, especially as they pertain to pyrite rejection.

Jan 1, 1989

Many organisations, including those in the resources industry have Board-level endorsed principles on sustainability. A key challenge, however, is how to systematically integrate these high-level principles into the design and operation of mineral processing plants. In an effort to meet this challenge the Sustainable Operations framework, called SUSOP®, was conceived and developed through the Corporative Research Centre for Sustainable Resource Processing (CSRP) in Australia. Somewhat analogous to HAZOP (Hazard and Operability Studies) which is well entrenched in the resources industry, the key aim of SUSOP® is to produce a holistic, systematic and rigorous methodology for identifying and assessing sustainability opportunities and risks. This paper argues the need for such a sustainability framework, presents the key elements of SUSOP®, highlights how case studies enhanced its development and articulates the reasons why such a framework will have growing importance into the future.

Jan 1, 2011

By William Bergeson

This paper presents the challenges of the Homestead Avenue Interceptor Extension (HAIE) project in downtown Hartford, Connecticut. The new 72-inch (1,830 mm) sewer pipeline project consists of installing approximately 3,010 linear feet (920 m) of PVC lined reinforced concrete pipe using pressurized face microtunneling. The entire alignment is located within soft to very soft, varved silt and clay. To the extent possible, the alignment was selected to avoid bedrock, glacial till, miscellaneous fill,buried steel piles, and utilities. Challenges for this project include low ground cover, crossing major transportation routes, and limiting settlement to prevent damage to historical buildings and critical utilities. The machine was selected for the ground conditions. Design calculations were performed for selecting the reinforced concrete pipe class and for evaluating settlement. The potential for settlement damage was evaluated using both conventional analysis and finite element analysis

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By Frank S. Hicks, Y. Charles Guan, Glenn A. Gruber

This paper describes a two-part program funded by the Florida Institute of Phosphate Research and performed by Jacobs. The first part of the program was to examine the application of ultrasonic treatment to clean phosphate particle surfaces. Florida phosphate pebble and rougher flotation feeds were treated in an ultrasonic trough to remove clays. Also, the de-oiling of rougher concentrates by ultrasonic treatment was tested. In order to improve the clay removal efficiency, viscosities of primary cyclone overflow from six beneficiation plants were studied in the second part of the program. Viscosities for different samples at the same clay % solids vary significantly, and increase exponentially with clay % solids content for the same sample. A method of controlling cyclone operation using on-line viscosity measurements and pump box level sensors is proposed to logically improve primary cyclone performance.

Jan 1, 2002

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

More than 5,300 mining professionals from around the world attended the SME Annual Meeting and Exhibit, March 1-3 in Denver, CO. Seventy three technical sessions highlighted innovative technologies and applications for the development of mineral resources. And the exhibit featured 421 companies worldwide and 632 exhibit booths. The 1999 SME Annual Meeting had 10% international attendance Professionals from outside the United States were guests at the first SME International Reception. Other meeting highlights included the Keynote Session. This pivotal session examined the international experience of North American-based companies. Speakers presented their perspectives on international explorations and operations. Keynote speakers included Robert Buchan, Chairman an( Chief Executive Officer, Kinross Gold; Dave Baker, Director Global Mining Project Management, Caterpillar; and Leendert Krol, Vice President International Operations Newmont Gold. Ihor Kunasz, 1998 SME President, made the introductory remarks.

Jan 1, 1999