Search Documents

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By O. A. Bascur

An expert process operation advisor system can increase plant efficiency, even in a complex, natural environment where not all elements of the production process can be measured directly. This system, develaped and tested in a Frasch process sulphur mine, monitors key process variables with extended qualitative pattern processing and provides on-line advise to the operators of sulphur production wells. An expert system framework captured common sense rules generated from years of experience obtained in the operation of a sulphur well monitoring system. The existent operating procedures were enhanced by process analysis using a qualitative modeling approach which provided extended rules for on-line classification of a well operational status and an expert alarm system. The methodology for development and implementation of the process advisor is presented in this report. Qualitative process modeling, statistical process control and heuristics were incorpomted into the process advisor resulting in a more efficient use of heat, an extended well operational life and the resulting cost savings. The computer process advisor also allowed the operator to concentrate his attention on the weak wells or wells in trouble. A process management system improved plant operation by automatically storing well data into a commercial database for operator validation. The enhanced relational data base system provided valuable and timely information for planning and decision making. The synergistic combination of on-line process analysis tools, expert control systems and database technology is shown to facilitate the flow of materials, energy and infomation in a modern plant.

Jan 1, 1990

By Scott G. Britton

The first section of this text delves into construction engineering techniques for successfully completing necessary underground production support projects. I will discuss alternative design concepts, installation practices, materials and material costs, completion time, and necessary labor for individual projects. The emphasis of this section is on describing each project thoroughly and providing a practical guide for the supervisor or engineer. There are four main construction categories for typical underground mining projects. These are: 1) Transportation of men and supply materials. This refers to track and wire installation and roadbed grading and ballasting. 2) Ventilation, composed of overcasts, man doors, regulators, and stoppings. 3) Drainage, including sumps, pumping stations, drainage networks, pumps, and face drainage. 4) Haulage of coal and rock from the face to the outside. The focus here is in the installation of belt lines, belt drives, transfer points, and vibrating bins/feeders. The first section shall fully discuss these four categories in regard to the construction engineer or supervisor designing, building, or improving a system. In addition, special projects such as surge bins, rotary dumps, and underground offices not classified under these categories will be discussed. For manageable purposes, I have limited the installation discussions to one or two approaches I feel have merit. The variation of installations in coal mining is endless, each with its own advantages and disadvantages. Therefore, the reader should not dismiss or restrict his thinking to only the approaches in the text. It serves as a guide only.

Jan 1, 1983

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

New developments in the non-invasive and real-time measurement of the velocity profile of slurry flow in horizontal pipes will be described. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities or higher solids concentration or both while avoiding solids deposition or plugging and their associated operational costs. In addition, advances have been made in the measurement and trending of pipewear on slurry lines. In contrast to manual methods, CiDRA?s system uses a permanently or semi-permanently installed ring of conformable ultrasonic transducers clamped onto the outside of the pipe. These transducers are used to measure the thickness of the pipe under their respective locations. This results in better repeatability, accuracy, and failure prediction, along with reduced labor costs. The benefit is significantly improved pipe wear monitoring in pipelines with abrasive solids. This provides an improvement in the ability to insure safe operation and avoidance of costly operational and environmental damage due to leaks caused by pipe wear.

Jan 1, 2009

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By Paul A. Rittenhouse

First of all, I want to thank John Dunlap for asking me to this AIME meeting in Denver. I was first introduced to Denver and The Rocky Mountains more than ten years ago and immediately decided it was one of the most attractive spots in the world. I've come back many times since and still welcome any opportunity to return, even if it means I have to prepare and give a paper on potash. When John Dunlap gave me this assignment, he told me that the program would include papers on the geology of potash, papers on new discovered potash deposits and new mines and asked me to discuss potash from the commercial point of view. He also asked me to include a supply/demand outlook for potash. However, one thing he did not mention was "how far into the future he wanted me to look" and it seems to me the time element is a crucial factor to you who are both geologists and miners as well as to me. In your case, you have to look far enough into the future to give you time to explore, find, evaluate, develop, and bring into production a commercial deposit. My mining associates and friends don't agree on how long that takes but it's probably somewhere in the range of eight to fifteen years. But, they all agree on one thing and that is that the time required is continually getting longer. Now my time problem is just the opposite. It is "relatively" easy, and I stress relatively, to identify and evaluate the importance of the various factors that impact on both the supply of and demand for a commodity such as potash if the time period is today. It gets a little tough if one has to project into tomorrow or next week or next month. And when we start talking in terms of a year, five years or ten or fifteen years, things really get sticky and the old crystal ball becomes mighty cloudy. But we economists and forecasters are not known for our temerity so let me get on with the job at hand and take a look at the world potash supply/demand outlook.

Jan 1, 1978

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By Scott G. Britton

Microcomputeranalysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran or other language dominated such efforts. These programs have taken years to develop and prove out. This article explores a new management tool used daily at Tanoma Mining Co. (TMC) to track and improve continuous mining systems through the use of microcomputers and Lotus l-2-3 software. Data provided by section foreman, shift foreman, and maintenance personnel are analyzed against predetermined goals. In this way, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The current results of this system on the productive output of TMC systems is on the order of 10% improvement. Thin seam coal mining is an industry within the broader industry of coal mining. Thin seam mining faces the same cost pressures and engineering problems as its higher-seam competitors without the advantages of moving volume per foot of extracted material to stay at an economic parity with others requires additional creativity within the management teams to extract higher productivity gains from the existing workforce and mining systems. TMC operates a deep mine in Indiana bounty, PA, about one hour northeast of Pittsburgh.

Jan 1, 1991

By David Shatwell

Recent epithermal gold discoveries in Chile and Bolivia provide increasing evidence of a belt of intermittent, epithermal, precious metal mineralization east of the main Andean porphyry copper belt. This relationship may be the result of an easterly decrease in the age of magmatism and erosional levels, in¬crease in depth above the underlying Benioff zone and consequent changes in magma chemistry, or some other unrecognized factor. Examples are: • The Choquelimpie gold-silver mine in Chile and numerous other epithermal prospects (such as La Riviera, Bolivia) in late Tertiary volcanics along the Chile-Bolivia border. These lie east of the belt that contains the Toquepala, Quellaveco and Cuajone porphyries in southern Peru and the Cerro Colorado, Copaquire and Quebrada Blanca porphyries in northern rhila

Jan 1, 1990

By Scott G. Britton

Mine exploitation is a broad subject whose focus is the technical skills or efforts needed for the extraction of mineral from a known ore body. Mine exploitation can be considered the very core of the mining engineering discipline. It begins at the conclusion of the exploration and development stages of mining and ends when the ore body is exhausted and the mine (or mines)closes and is reclaimed. Section 8 on mine exploitation is comprised of seven chapters: (1) classification of mining methods, (2) mine surveying and mapping, 3) systems engineering, (4) computer methods, (5) labor relations and training, (6) management and administration, and (7) mine closure, sealing, and abandonment. Each chapter focuses its efforts towards providing detailed and useful information for the engineer on basic mine exploitation principles. The information can be applied to a broad range of mining problems without regard to mineral type or mining method.

Jan 1, 2008

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By F. C. Bond

Nature of Empirical Calculations The size reduction of large tonnages of ore and rock is an operation of great magnitude. It is a necessary and important part of industry. Its development has been motivated by practical need and has followed the path of an industrial art without much help from theoretical science. Knowledge has been accumulated from experience. Trial and error established the methods; then collected data were tabulated and served as the basis for empirical equations that have been continually modi¬fied and amplified as new data became available. These equations now constitute the bulk of our present knowledge of comminution. There is no accepted scientific theory that is basic to comminution. In electrical, mechanical, and civil engineering, as well as in many other industrial activities, such theories exist and are extremely help¬ful, but rock is essentially heterogeneous, and the zones of weakness that control its breakage are thoroughly diversified. No theory has yet been discovered which can account for the variability of rock, although many attempts have been made. Empirical equations tell nothing of the why of a phenomenon, but if they are properly derived they can tell much about the how. They always represent only an approximation of behavior but never a law. In a proper empirical equation a symbol is assigned for each of the variable quantities that obviously affect the relationship. In a grinding mill these include mill diameter, mill speed, and feed rate among them. In setting up and revising an empirical equation the cardinal princi¬ple in establishing and modifying it is this: any change must be strictly ascribed to the variable which caused it. A useful empirical equation is rendered useless when a change in any convenient coefficient or exponent is made to make it fit a particular set of data, without certainty that the altered coefficient or exponent is the responsible variable in the new data. Such indiscriminate revisions have brought the use of empirical equations into some disrepute. When existing equations are changed to accommodate new data it is a good rule to make a change which gives results intermediate between the new and the old. A halfway point is usually a good choice.

Jan 1, 1985

Dynamic permeability is a significant hydrologic condition associated with in-situ leaching at the Cyprus Casa Grande operations. Several factors contribute to changes in the permeability conditions. They are: 1) hydraulically induced fracture development, 2) geochemical changes during leaching in the rock matrix, and 3) changes in the relative degree of saturation of the deposit. Dynamic permeability conditions were evaluated using available pressure and flow rates from the 58 injection and recovery wells obtained over one year period. A finite element, 2-D hydrologic model called INVERT which is designed to estimate aquifer parameters under transient and steady state flow conditions was used for the investigation. The permeability conditions during 7 different steady state intervals throughout the one year time frame were determined. The results confirm that big changes in permeability occur as a function of time as well as a function of injection pressure condition.

Jan 1, 1991

By V. R. Degner

The trend in both the metallic and non-metallic mining industry is toward processing increasing y higher tonnages of lower grade ores, thereby resulting in a growing interest in progressively larger volume individual machines in the flotation circuit. Because of the relatively high cost of large flotation machine development and evaluation, it is important to establish a rational basis by which the existing smaller flotation machine experience can be extrapolated to establish the configuration of the next larger family of flotation machines with a minimum of development modification in the field. This paper reviews the R&D approach used in translating smaller flotation machine experience to establish the configuration of a 1000 cu ft (2B.3 cu m) induced air machine. Internal cell hydrodynamic principles, which governed this extrapolation, and cell (liquid) surface and froth management considerations will be reviewed, and prototype machine mill tests will be summarized.

Jan 1, 1978

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

The oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bi, Pb, Sb, As, and Cu contents in the speiss by two-step simulation differed from the industrial data by 0.6 wt.%, 0.8 wt.%, 2.6 wt.%, 7.2 wt.%, and 8.6 wt.%, respectively. Twostep simulation results indicated that the speiss partitioning of Sb, As, and Cu increased from 60.1%, 32.3%, and 27.5%to 81.6%, 67.8%, and 47.2%, respectively, with the smelting temperature increasing from 1050 °C to 1250 °C. While the metal partitioning of Sb and Cu increased from 0% and 2.7% to 15.2% and 13.3%, respectively, with the separation temperature increasing from 400 °C to 700 °C.

Oct 19, 2020

By R. Pazhianur

Cathodic Protection using impressed current was employed to reduce the wear of the mill wall during ball mill grinding. Wear rates were determined from weight-loss measurements made on four, I-inch diameter, mild steel coupons installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH values of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 40-60010. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It is also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1996

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022