Search Documents

In a world dependent in part on the consumption of depletable natural resources, development of new areas of mineralization is a necessity for replacing those reserves. Exploration, which is the initial task of replacement, is an information-gathering process which supplies input for management decisions on mine development. If the demand for resources is the driving force of exploration, then the scientific basis for its pursuance is the hypothesis of anomalous mineralization in a metallogenic province, which is tested by measuring physical characteristics of natural phenomenon. The resulting data are reduced, analyzed, and interpreted to locate expressions or responses associated with possible ore bodies. The process is, in fact, repeated in ever increasing measurement detail to increase the accuracy and precision of information for decision making. Exploration ceases when management makes the decision to develop a mineralized area, to hold a property for more favorable market conditions, or to drop a property because it is not economically viable.

Jan 1, 1979

By Henry P. Ehrlinger III, Latif Khan, John M. Lytle

The primary purpose of this project was to produce and test coal concentrates made from coal preparation plant waste fines for use in a slurry-fed gasifier. Concentrates from several individual waste streams were examined to determine their amenability as feedstock for a slurry-fed, slagging, entrained-flow gasifier. The tests included analyses of the plant feed and product, material balances, and estimates of gasification reactivity and of pumpability. The following preparation plant fines were examined: • fresh rejects produced in a plant processing underground- mined Springfield Coal • fresh rejects produced in a plant processing underground- mined Herrin Coal • fresh rejects produced in a plant processing surface-mined Springfield Coal and Herrin Coal • Five-year old impounded fines rejected during processing of underground mined Herrin Coal. At high coal recoveries the Btu content of the concentrates was greater than the Btu content of the utility product from the plant. The coal recovered from fines was found to be entirely acceptable for gasification and pumping without additives.

Jan 1, 1995

By R. Hogg, T. F. Dumm

Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been com- pared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes. Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples.

Jan 1, 1987

By J. Alvarez, S. H. Castro

The feasibility of chalcopyrite-pyrite separation in the flotation of a chalcopyritic copper ore, at reduced surface tensions regulated by methanol, was investigated. It was found that with methanol dosages from 0.5% to 1.5% v/ v, the chalcopyrite might be effectively separated from the pyrite, without use of other flotation reagents and pH regulators. However, under this simple condition, the chalcopyrite recovery was only around 50%, recommending the use of other reagents to reinforce the collector action. Low dosages of different collectors were tested, including SF-323 (Shell Float), S-6588 and S-7251 (Cytec), and S-701 (Molycop). Very promising results were obtained with low dosages of the collector S-701 and 1% v/v of methanol in the pulp, which evaluated against a reference test, gave similar copper recovery, higher Mo recovery and higher depression of pyrite. Consequently, this is an alternative process which does not require the use of lime to depress pyrite.

Jan 1, 1995

By R. Bhaskar

Although the health effects of airborne dust in underground coal mines are well recognized, a lack of understanding remains about the fundamental mechanisms of dust generation, transportation, deposition and dust-lung reaction. This study was intended to contribute to the understanding of dust transportation and deposition mechanisms in underground mine airways. Data from in-mine experiments carried out under controlled conditions in a straight section of a longwall panel with three different airflow velocities and two different types of coal dust (bituminous and semi-anthracite) were used to determine the turbulent deposition rate of dust particles. Measurements of ambient dust concentrations and deposition along the mine airway were obtained and the total dust deposition velocity (rate) was calculated. The deposition velocity of turbulent diffusion was estimated based on the experimental data and theoretical equations. The effects of airflow velocity, particle size, particle density and distance from the dust source on gravitational, turbulent and total dust deposition are discussed along with related conclusions.

Jan 1, 1995

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By F. A. Kruse, R. J. Madrid, P. L. Hauff

Sub-microscopic gold grains in disseminated gold deposits in Nevada are often directly associated with the clay mineral illite. Delineation of gold ore-zones can be improved by accurate characterization of the associated illite varieties or polytypes. X-ray diffraction studies of clay minerals from several disseminated gold deposits demonstrate that illite polytypes reflect lateral and vertical zonation around the ore bodies. Polytypes act as geothermometers indicating temperatures of ore deposition and proximity to hypogene and supergene fluids. Visible/near infrared spectral measurements using a field-portable reflectance spectrometer provide a reconnaissance technique for mapping the in-situ distribution of illites. Changes in the visible/near-infrared reflectance spectra are observed as illites progress from the lower temperature, less ordered 1 M variety to the higher temperature 2M type. The combination of the reflectance spectroscopy with the X- ray diffraction data creates a powerful tool for detailed mineralogic mapping for gold exploration.

Jan 1, 1989

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By A. B. Cecala

The US Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the US coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1995

By Nopadon Mantajit, Dallas W. Davis, Somsak Potisat, Prasert Kumalachan

For centuries Thailand has been a significant, though primarily unofficial, producer of gold. Panning has been the traditional way of making a living for innumerable villagers during the December to May dry season following the harvest. During this period groups can be seen working the streams, rivers, fields and dry valleys at as many as 90 localities in 28 provinces. Attesting to their efforts are the five and a half ton solid gold Buddha at Wat Trimit and much of the gold jewelry sold in Bangkok. This traditional panning will continue, and probably become more extensive, in harmony with commercial endeavors using modern technology suitable for extraction of gold from types of deposits for which gravity separation would give very low recoveries. Several such deposits have been discovered in the course of geochemical and geological surveys conducted by the Royal Thai Department of Mineral Resources with the object of contributing to early interpretation of the results of a country-wide airborne survey.

Jan 1, 1987

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By V. L. Jr. Davis, F. L. Stanley, P. J. Bethell

Fwe 3 m (10 ft) diameter Microcel™ flotation columns were installed at Clinchfield Coal Company's Middle Fork preparation facility in order to reduce product ash and increase recovery and plant capacity. The Middle Fork facility is utilized for the recovery of fine coal from a feed stream that consists primarily of 1 .5 mm x 0 material. The columns replaced conventional flotation cells for the treatment of the minus 150 pm fraction while spirals are used to upgrade the plus 150 pm material in the plant feed. The addition of the column flotation circuit resulted in an increase in plant capacity in excess of 20 percent while reducing the flotation product ash content by approximately 7 percentage points. Flotation circuit combustible recovery was increased by 17 percentage points. This paper discusses circuit design, commissioning, and sparging system design. Circuit instrumentation, level control, reagent system control, performance comparisons with conventional flotation, and general operating procedures are also discussed.

Jan 1, 1995

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By M. Prasad, G. M. Rao, T. C. Rao, A. K. Majmudar

A two-step flotation scheme was employed to beneficiate a low-grade, cherty-calcareous rock phosphate ore from the Jhabua district, Madhya Pradesh, India. In the first stage, apatite and calcite ire floated together to remove silica, and, in the second stage, calcite is floated and apatite is depressed. The reagent scheme consists of sodium oleate, sodium silicate, orthophosphoric acid and sulfuric acid. The effect of reagent dosages on the efficiencies of separtition in each stage was studied systematically. A flowsheet was proposed for the processing of a low-grade phosphate ore containing 12.5% P2O5, 26.5% SiO2 and a CaO/P2O5 ratio of 2.64 (=32% calcite). The proposed flowsheet would produce a composite phosphate concentrate containing 27.2% P2O5, 6.37% SiO2 and a much reduced CaO/P205 ratio of 1.66. The total P2O5 recovery for the composite concentrate would be 73% .

Jan 1, 1996

By B. C. Paul, R. Q. Honaker, M. Huang

Froth flotation is now, the most commonly used method for cleaning fine-coal fractions in coal-preparation plants. Past research and industrial practice have demonstrated that froth flotation achieves excellent separation efficiencies for fine coals having only a small fraction of middling particles. However, the efficiency of froth flotation decreases sharply as the concentration of middling particles increases. This is due to the flotation of high-ash particles that have a small amount of hydrophobic coal present at the surface. Because gravity-based processes are much more efficient for the treatment of middlings, the application of centrifugal washing for fine-coal cleaning was studied with an emphasis on the primary cleaning of fine-circuit feed. Results are shown of a parametric study that used a semibatch Falcon centrifugal concentrator. The results of the study revealed that separation performance is a function of particle size, bowl geometry, feed solids content and feed rate.

Jan 1, 1996

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By A. W. Scaroni, C. Y. Tsai

The effect of particle size and composition on the pyrolysis and combustion of a pulverized bituminous coal in an entrained-flow reactor has been investigated. Predicted time-temperature histories of the coal particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm (about 140 mesh). This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate before ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of an HVA bituminous coal that were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite-rich samples.

Jan 1, 1987

By Robert Dimock

The successful management of large dispersed mineral operations is dependent upon accurate and timely decision making. The plant locations providing the data to support the decision making process are generally separated by distances which elongate the time required to accumulate the data at a central focus. The need exists to examine operational data in context with total mining operations, and in relation to target projections and historical trends. The use of microcomputers for local information tasks is an established capability. Grouping microcomputers into local-area networks is rapidly becoming established. Interconnecting multiple local-area networks to provide a free flowing stream of information between all operational locations of a mining enterprise is possible with use of some emerging technologies. The benefit of the potential interconnections and rapid transfer of information can readily be seen from a production reporting perspective. Numerous other advantages exist' by providing routing to enable a workgroup to be established between separated work functions.

Jan 1, 1989

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998