Search Documents

By Dao De Xu, Heechan Cho, Mark S. Klima

A study was conducted to determine the feasibility of using dense-medium centrifugation for separating fine (-150 µm) coal. A centrifuge provides the capability of varying the rotational speed and retention time independently, which offers the potential for a higher degree of control as compared to a dense-medium cyclone. Tests were conducted with a 140-mm diameter by 76-mm long Plexiglas separator, which was fitted with appropriate feed and discharge pipes to allow continuous separations to be made. A suspension of ultrafine (-10 µm) magnetite and water was used as the dense medium. The effects of operating conditions, including the magnitude of the 'g"-force and retention time, on centrifuge performance were investigated.

Jan 1, 1995

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

The generation of microscopic bubbles by cavitation may enhance particle-bubble attachment and improve flotation performance. It is shown in this paper that tiny bubbles or cavities can be generated by strong shear and turbulence in high speed liquid flows. These conditions create the necessary pressure fluctuations in the bulk water to cause the local pressure to drop below a critical value. The formation of bubbles is favored by high dissolved gas contents to promote gas diffusion into the cavities, and by the presence of surfactants to provide some mechanical strength due to the adsorbed film. Experimental results on bubble formation by cavitation and consequent flotation of fine silica (d50 = 1.6 µm) are presented.

Jan 1, 1995

By K. H. McDaniel

Eight mine weather stations (MWSs) installed at the Waste Isolation Pilot Plant (WIPP) to monitor the underground ventilation system are helping to simulate real time ventilation scenarios. Seasonal weather extremes can result in variations in the natural ventilation pressure (NVP), which can significantly affect the ventilation system. The eight MWSs, which previously collected and stored temperature, barometric pressure and relative humidity data for subsequent NVP calculations, were upgraded to provide continuous real time data to the site-wide central monitoring system. These data can now be utilized by the ventilation engineer to create real time ventilation simulations and can indicate trends that assist in the prediction and mitigation of NVP and psychrometric related events.

Jan 1, 1999

By Donald L. Meredith, Jeffrey Harris, Donald A. Stanley

Principal Components Analysis (PCA) is a versatile, multivariate statistical method that the Bureau of Mines is applying to mineral processing data to achieve data simplification and pattern recognition. The principal components are obtained from an eigenanalysis of the data matrix. To achieve data simplification PCA replaces a larger number of measured variables with a smaller set of principal components and at the same time removes a significant amount of experimental error. Data simplification and error reduction make PCA useful in process control. Plots of the individual principal components form the basis of a pattern recognition technique that allows detection of significant variations in the structure of the data. These applications of PCA are illustrated with appropriate mineral processing data.

Jan 1, 1993

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

By L. A. Puchkov

The creation of automatic methane concentration control systems presupposes the use, as a control factor, of the air rates in workings and in mine as a whole. These systems present a complicated set of computers and software, including as major components the following - systems for detecting methane concentration and air rate; - telemechanics systems; - programs and means of data processing; - programs and means of air rate control in workings and main fan capacity control. The paper analyses the experience of development and exploitation of automatic methane control system in gassy mines of the USSR Donetz coal basin. Much attention is given to the study of technological factors influence upon aerogasdynamic process using automatic methane control system.

Jan 1, 1989

By K. Hanumantha Rao, K. S. E. Forssberg

The limestone deposit of Gâsgruvan, Sweden contains around 89.2 per cent of calcite. Conventional and column flotation studies have been carried out using sodium oleate and modified fatty acid collectors in the presence of sodium silicate modifier. The effects of collector and silicate concentrations, and particle size on the flotation response of calcite have been investigated. The results have been discussed in comparision to the performance of conventional and column flotation cells. The feed size is found to be a significant factor to achieve a high grade calcite concentrate either by conventional or by column flotation. The loss of selectivity at fine particle sizes is examined using a modified DLVO theory.

Jan 1, 1995

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By Y. K. Yen, J. D. Miller, C. L. Lin

A PC image-based, on-line coarse particle size analysis system is being developed for the control of crushing and grinding circuits. Initial results had indicated that the system is accurate when tested with irregularly shaped particles which are stationary and do not overlap with each other. Now the system has been successfully tested in the dynamic mode with a moving belt conveyor. On-line size analysis for actual plant operations is discussed and includes: (1) the video system with respect to lighting and data acquisition requirements for a rapidly moving belt and, (2) image sampling, specifically the number of observations needed for accurate sampling and the total time required to perform the calculations for a representative data set.

Jan 1, 1993

By Raphael Mourad, Colin R. Phillips

Investigation of the traps in LiF:Mg, a multi-peak phosphor, was carried out using simple phosphorescence decay analysis. Half lives at room temperature of the trapping centres (peaks -lb, -la, -1, 0, 1, 2, 3a and 3) in the phosphor after irradiation with [a] radiation were found to be 3 s, 5 s, 28 s, 4 min, 15 min, 1 h, 6 h and 2 d respectively. Justification for the method of analysis is pro- vided and the results of measurements compared with published data. The effects of pre-annealing at 400°C for 1 h and 80°C for 24 h on the trapping configuration and on the trapping efficiencies were also studied.

Jan 1, 1981

By F. C. Loughnan, Shane B. Sadleir

Bauxite is currently produced at three centres in Australia: - Weipa in northern Queensland; Gove on the northeastern tip of Northern Territory; and in the Darling Range near Perth, Western Australia. At each of these centres the bauxite is of Tertiary age and occurs as blanket-like, lateritic crusts in which gibbsite is the predominant mineral. Development was essentially in situ although possibly the deposits, particularly at Gove, are in part of transported origin. All of the deposits formed from quartz-rich parent rocks with those at Weipa and Gove being derived from kaolinitic sands while in the Darling Range, granite and other crystalline rocks of Precambrian age immediately underline the lateritic bauxite.

Jan 1, 1984

By Milton E. Wadsworth, Ximeng Zhu

Impurity metals can markedly influence the anodic dissolution of gold in the presence of cyanide. Several important findings related to the influence of lead are reviewed and some new observations presented. Based on the effect of pH, the scan direction, and voltage, it may be shown there are three separate voltage regimes where lead influences the anodic dissolution of gold. These are related to Pb°/ HPbO2, Au-Pb /HPbO2, and HPbO2/PbC2; oxidation-reduction reactions which provide low resistance paths for electron exchange. The gold dissolution rate was determined by direct solution analysis and is compared to the rate implied by electrochemical measurements.

Jan 1, 2005

By A. C. Noble, D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1992

By S. Chander

The advantages and disadvantages of various techniques available for controlling reagents in the mineral flotation systems are discussed. Special interest is placed on potentiometric and voltammetric sensors for monitoring flotation pulps. Different approaches to increase the sensitivity of detection and to facilitate in-stream monitoring of solution species are also discussed. The potentiometric sensors are simple to use but are limited by the availability of an electrode reversible to the species to be monitored. In some cases the response signal could be unreliable due to the presence of interfering species. In comparison, voltammetric sensors require a higher degree of instrumentation which, however, provides an opportunity to decrease interferences and increase levels of detection.

Jan 1, 1993

By M. M. Hajdasinski

For decades, the internal rate of return (IRR) project-evaluation criterion has been under increasing criticism. Torries (1998a) defends the beleaguered criterion. He claims that, as a project-evaluation and ranking instrument, the IRR is as suitable as the net present value (NPV). Torries also maintains that using the IRR to rank projects does not require the incremental approach and introduces his own alternative ranking approach. This paper disputes Torries' pro-IRR arguments and demonstrates that the IRR is a theoretically flawed and operationally dysfunctional criterion whose true meaning has persistently been misinterpreted. In a forthcoming paper by the author it will be shown that Torries' IRR-based project-ranking approach is flawed as well.

Jan 1, 2000

By Steven Atkin, Rens Verburg, Bryony Hansen, David McWharter

The use of paste tailings as underground backfill and for surface disposal is rapidly expanding, and with it comes the requirement to understand and predict its long-term environmental stability. This paper presents the results from a kinetic testing study performed on cemented tailings paste mixtures under both subaqueous and subaerial conditions. In addition, the effects of grainsize reduction are investigated. It will be demonstrated that the long-term weathering behavior of tailings paste is controlled by its physical and chemical characteristics, as well as its placement conditions. The testing indicates that subaqueous disposal of paste inhibits acid generation, whereas the exposed samples produced acidic leachate despite the presence of cement added to meet geotechnical requirements.

Jan 1, 2000

By P. Somasundaran, J. T. Kunjappu

Spectroscopic techniques are becoming increasingly popular for characterizing the interior of adsorbed layers of surfactants and polymers at solid- liquid interface as well as in the identification of com- pounds on mineral surfaces. This review encompasses the application of fluorescence and ESR spectroscopic techniques to reveal the microscopic environment of the adsorbed layers of surfactants and polymers on minerals with a special reference to the adsorption of anionic surfactants (e.g., sodium dodecyl sulfate) and polyelectrolytes (e.g., polyacrylic acid) at positively charged mineral (e.g., alumina) - water interfaces. Finally, the utility of XPS and auger techniques to identify the surface elemental composition of different mineral species has been related to their flotation efficiency.

Jan 1, 1987

By J. D. Miller, J. Hupka

Environmental applications of the air-sparged hydrocyclone (ASH) technology are presented. The original ASH design used porous sintered steel or porous polyethylene tubes as spargers. To diminish/prevent plugging and to reduce pressure head loss in the gas path a wire screen sparger and new hydrocyclone design have been developed, which allows for wide application of the technology to solve environmental problems and to be used as a chemical reactor. Field and laboratory trials have shown that the ASH technology might be preferred for the stripping of volatile organic compounds WOC) from contaminated water. The ASH has also been developed for absorption of SO2, toluene vapors, and for the recovery of cyanide.

Jan 1, 2005

By D. A. Day, H. L. Marsh, P. J. Stephens, C. A. Wiggins

Lightweight cellular grout backfill behind pipe-in-tunnel has been gaining increased acceptance in the tunneling industry and has proved to be both practical and economical. Two successfully constructed projects, the Upper Scioto West Interceptor Sewer (USWIS), in Columbus, Ohio and the Benbrook Pipeline Tunnel Project in Fort Worth, Texas will be discussed. The projects represent two different but successful applications of lightweight cellular grout backfill. The USWIS placed the grout behind precast reinforced concrete pipe, in water bearing limestone, and in close proximity to residential water wells. The Benbrook Project placed grout behind 6,096 meters (20,000 feet) of steel pipe from just two locations, eliminating major surface disruption typically associated with the placement of pumped concrete.

Jan 1, 1999