Search Documents

By I. E. Zevgolis

A comprehensive critical review on the subject of sulfates-induced swelling behavior of lime-treated soils is presented in this study. Starting with the description of a well documented case study, the mechanisms behind the swelling behavior and the factors that affect this behavior are discussed. Then, the major experimental methods of sulfates content determination are briefly presented. Finally, an attempt is made to categorize sulfates level and equivalent risk for civil infrastructure. The paper indicates that limited work has been done, not only on identifying safe conditions for use of chemical stabilizers in presence of sulfate rich soils, but also on developing materials and methods to avoid, or at least mitigate, the problem.

Jan 1, 2008

By Richard M. Bennett

Twelve linear test foundations were constructed over an advancing longwall panel in southern Illinois, six were located along the centerline, and six in the maximum tension zone. One footing in each set was a control foundation constructed according to conventional practice. It suffered severe damage. Footings with reinforcing bare and post-tensioning had much smaller elongations, with the post-tensioning preventing cracking of the footing. Footing-soil interface treatments of plastic-on-sand and plastic-on-soil served to reduce damage. The addition of steel fibers to the footing had about the same effect as an interface treatment. Sill plate construction (butt-jointed versus lap-jointed) appeared to significantly affect the behavior.

Jan 1, 1986

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By Del Brock, Dan Wooton

The design/build of two adjacent vertical mine shafts in difficult ground conditions at a mining complex in the midwestern United States required innovative construction techniques. Construction of the 267-m-deep Service Shaft required full depth dewatering wells and ground freezing. Blind drilling was utilized to excavate the 257-m-deep Production Shaft and it was finished with a steel/concrete composite liner that was floated into place. An equally unique component of the installation included supplying a high capacity vertical conveyor system, featuring a 273-m-lift. Other components of the project include the mine level development, as well as the design and installation of three hoisting systems, including a 45-ton capacity men/materials hoisting system.

Jan 1, 2003

By M. A. Berdine, C. N. Thompson, D. Brock

The raise bore method of shaft construction has been success-fully used in the mining and construction industries for over thirty years. In the mid 1990’s, Twentymile Coal Company (“TCC”), now affiliated with RAG American Coal Company, used this method for a moderately deep small diameter shaft and the raise bore and slash method for a shallow larger diameter shaft. In late 2001, TCC contracted to raise bore a 431-meter deep, 6.2-meter diameter shaft. During the raise bore and shaft lining processes, regional horizontal stress fields resulted in extensive elliptical caving beyond the original design diameter. This paper discusses the engineering approaches and procedures used to safely complete construction of the raise bore shaft.

Jan 1, 2004

By Peter A. Spencer

Much criticism has been levelled at bacterial oxidation over the quantities of air required for successful operation. Examination of the oxidation reactions and the assumptions concerning oxygen transfer made in the literature (1) indicate that the aeration requirements can be much less than those beirig suggested. Observations made on a large scale pilot test have confirmed reasonable aeration levels in extended site operation over a six month period. These aeration levels have implications for the engineering design and the power needed for aeration and agitation. Thus, these parameters effect both capital and operating costs as well as influencing the complexity of the design and normal operation. A number of companies have developed bacterial oxidation cultures intended for commercial ·expl oi tat.ion ( 2, 3, 4). Most of these cultures have been based on Thiobacillus and operate at temperatures between 30°c and 40°c. This temperature range limits their application in hotter regions unless means for both heating and cooling are provided in the design. Thiobacil!us cultures are also reported as not able to oxidize arsenic (III), which may limit the application of these cultures to successfully treat arsenopyritic ores and concentrates (5). BacTech (Australia) Pty Ltd has developed a culture which operates at temperatures above 4o0 c and which has been tested in a large site based continuous pilot plant at up to 55°c over a six month period. The culture showed resistance to high levels of soluble arsenic, allowing the arsenic to be retained in solution for control led precipitation and disposal. Data for. the arsenic precipitates indicated that these waste solids were relatively stable and, under the correct circumstances, were suitable for disposal into tailings dams without causing environmental problems.

Jan 1, 1990

By John C. Ferm

The role of geology in coal exploration, mine planning and mine development has, in the past, been relatively small. The primary reason for this lies in. the simplicity of geologic concepts that were necessary to bring these operations about. These concepts can be briefly stated as follows: 1) coal occurs in the beds or layers and is overlain and underlain by shales, sandstone or limestone in varying porportions, 2) each coal bed has been given a name and certain quality characteristics can often be associated with a named bed and 3) coal beds (and their adjoining rocks) are often folded into broad anticlines or synclines and, in some places, displaced or faulted. In actual practice, however, these simple principles have been found wanting. Thickening, thinning, pinch outs or changes in coal quality occurred but the occurrence was apparently unpredictable and the only real solution to such problems seemed to be practice and experience. This combined with ingeneous engineering solutions have provided answers to most questions. Perhaps a more fundamental reason that geology could offer so little input to coal mining is that the thickest, most persistant and best quality coal seams followed the above stated rules fairly well. In many areas, however, such seams are now nearing exhaustion and the increased demand for clean, non-polluting, safe energy is quickly bringing a need for techniques of exploration and mining procedures that will make development of formerly unminable seams a profitable venture. For the past 20 years some considerable body of knowledge has been added to the framework of the geology of sedimentary rocks and it is the purpose of this paper to present some of these newer ideas that will be useful in solving some of the present problems of coal exploration and development.

Jan 1, 1976

"Australia’s largest rail freight network operator, the Australian Rail Track Corporation (ARTC), has selected GE Transportation’s Movement Planner solution as the key technology enabler for its Hunter Valley-focused network control optimization program.ARTC’s Newcastle-based network control, is the nerve center of Hunter Valley rail operations, where locally based train control professionals make thousands of decisions every day to safely support the annual movement of more than 24 kt/h (26,400 stph) of freight, and tens of thousands of coal, freight, grain and passenger trains each year.ARTC plans to transform its train control function by integrating and then building on Movement Planner, an advanced software solution by GE Transportation that provides real-time rail traffic planning and optimization to enable freight to move more efficiently. “The Hunter Valley rail network is one of the busiest and most complex in the country, supporting the largest coal export port in the world,” ARTC managing director and chief executive officer John Fullerton said.“As bulk freight demands grow, rail operators like ARTC and supply chains like the Hunter Valley coal network need to be creative in the way they respond so the Australian economy doesn’t miss out. That’s why we have conducted a worldwide search to find globally proven solutions that will improve our network productivity and efficiency,” Fullerton said.The Movement Planner solution considers multiple factors including train schedules, trafficcontrol systems and train movements relative to each other and then develops an optimized traffic plan for the trains throughout the network. Existing GE customers have benefited from increased visibility of network operations, higher velocity, less dwell times, and improved on-time performance across their networks."

Jan 1, 2018

By L. G. Closs

Gold continued to be the primary focus of minerals exploration worldwide during 1995. Other targets, though, included primary diamonds and base metals, especially copper deposits amenable to solvent-extraction/electrowinning (SX/EW) processing. The discovery of nickel, copper and cobalt at Voisey Bay in Labrador, Canada was an unusual surprise. Meanwhile, exploration geochemistry continues to evolve to meet new challenges. The major event in this category during 1995 was the17th International Geochemical Exploration Symposium (IGES) held in Townsville, Queensland, Australia in May. The meeting was sponsored by the Association of Exploration Geochemists, which celebrated its 25thanniversary of service to the mineral industry, and the Economic Geology Research Unit of James Cook University, Townsville.

Jan 1, 1996

By Steve Lloyd, Mary Anne Antonioli, Byron Darnton

Pegasus Gold Corporations' Montana Tunnels mine began oper­ation in March 1987. The process plant at startup consisted of a bulk flotation circuit followed by leaching of the reground bulk concentrate. The leach residue then advanced to selective Pb/Zn flotation. This original circuit had its share of problems, and the leach circuit was abandoned after six months. The bulk flotation circuit was modified to selective Pb/Zn flotation at this same time. Gravity concentration was researched early on, prior to selecting bulk flotation with leach as the flowsheet of choice. Flotation was deemed to be more practical than gravity due to the lower capital and operating costs. No further work was done concerning gravity concentration until 1990 when it was decid­ed to investigate ways to diminish the occurrence of free gold reporting to the flotation tailings.

Jan 1, 1996

By John C. Schneider

In the mid 60's Prochem & Hydrochem Development, it's research division, developed the high efficiency Maxflo impeller. Since the Maxflo impeller had a design that had proven to be very efficient in gas-liquid-solid contacting, it was a natural extension to apply this design to flotation & the research commenced in the mid 80's. An opportunity to test the energy savings occurred at Dickenson Mines in 1987, & comparative results with existing conventional flotation cells showed a marked increase in capacity, grade & recovery with 25% less power applied. This r success was followed by the installation of the fist agitated Flotation Colunm (5ft. dia. x 25ft. tall). As a result of the Dickenson success, Hydrochem started a comprehensive 2-part research program in 1988. At Randol Gold Forum 1988 a paper by Hydrochem was pre

Jan 1, 2000

By Michael Mccorkle

The Turnkey Project contracting approach is a very viable project delivery system for many mine and mill owners. Generally speaking, the Turnkey Project approach makes sense when the owner knows what it wants, is willing to accept the contractors judgement on process elements and maintenance standards, and early construction completion/facility stmt-up are of primmy importance. Projects with unclear process and project objectives make poor candidates for true Turnkey applications. If the objectives are unclear, under development or significant refinement, the owner's effort should go into a good schedule "A" package allowing Engineering, Procurement, and Construction (EPC) contractors to develop cost and schedule proposals for the final design ( engi­neering), procurement and construction of the facility. Figure 1 and 2 graphically depict (in general terms) the stan­dard Design-Bid-Build, Construction Management (CM) Fasttrack, EPC, and Turnkey Approach.

Jan 1, 1998

By Dale C. Matthews

The Getchell Gold Hine is located about 40 miles northeast of Winnemucca, Nevada. Gold was discovered at the mine in 1934 and production was started in 1938 and ended in 1967 for its first phase of operation. Gold production during this period was about 800,000 ounces. In 1983, FirstHiss Gold Inc. purchased the property and initiated an exploration program that proved minable reserves of about 1,300,000 ounces of gold remained in the mine. During the exploration period, metallurgical testing was conducted to determine the most economical process that could be utilized for recovery of gold from the very refractory ore. After extensive investigation, pressure oxidation of the ore was selected, Engineering for the new plant commenced in 1987 and construction was completed in 1989 at a cost of about $87,400,000.00, not including financing cost.

Jan 1, 1990

By T. Valentine

The SX-EW operation at Morenci includes three electrowinning tankhouses. Stainless cathode blanks require the use of insulating plastic edge strips, which typically have a service life of 1-2 years, therefore, regular replacement of edge strips is a fact of life in tankhouse operations. The largest tankhouse, Central, converted from starter sheets to stainless steel cathode blanks in 1999. During the first year of stainless blank operation at Central Tankhouse, the initial installation edge strips started failing at accelerated rates and there was a sudden need to replace edge strips and repair between 350 and 400 cathode blanks per day. This paper details the design and building of cathode repair shops at the Morenci tankhouses, including choice of equipment and layout design. The objective was to increase efficiency through the use of cathode handling equipment and flow of material.

Jan 1, 2002

By Patrick R. Taylor

The hydrometallurgical fundamentals review did not arrive in time for publication in the May issue. Papers presented at the SME Annual Meeting, in Phoenix, AZ were available as preprints. The EPD Congress 1992 from The Metallurgical Society had several papers related to hydrometallurgy. Minerals Engineering 1992 was published in Minerals Engineering and contains several papers related to hydrometallurgy. In addition, a conference was held to honor Ernie Peters. The proceedings contains a large number of hydrometallurgy papers. Precious metals Gold extraction in the potassium cyanide-primene JMT sulfate-Xylene system was studied by Caravaca and Alguacil (Hydrometallurgy). Adams, Friedl and Wagner presented results on the mechanism of gold cyanide adsorption onto activated carbon (Hydrometallurgy). Adams also studied the adsorption of silver cyanide and used an IR method to evaluate adsorbed aurocyanide species on activated carbon (Hydrometallurgy).

Jan 1, 1993

By E. Sarris

Tailings dams are large-scale earth-fill embankments that are designed to contain mining wastes from ore dressing plants. Most commonly tailings dams are constructed in stages in order to keep up with the increasing volume of mine tailings. Staged construction using various methods (like up-stream, down-stream, and centerline) is generally considered as a very effective way to construct this kind of embankments. The present study is devoted to the investigation of the behavior and the stability of these geostructures under static conditions. In order to accomplish this task, elaborate two-dimensional numerical models are examined, utilizing the geotechnical finite-element code PLAXIS. Numerical analyses are conducted for all three types of tailings dams in order to obtain the potential modes of failure, while the corresponding factors of safety are determined by the shear strength reduction technique.

Jan 1, 2005

By A. Smithson

It is generally accepted by British mining engineers that coal will continue to be worked by the. advancing or retreating longwall system for the foreseeable future. At the coal face, the emphasis will be on better machine utilization; increased equipment reliability; modular design and more standardization; remote control and monitoring; and a continuing drive to increase productivity and safety. Improvements at the face can be sustained only if there are corresponding improvements in efficiency elsewhere in the mine. Coal handling systems, for example, must be able to accept increased tonnages without creating bottlenecks. As workings move further from the shafts, the time taken to transport men and materials must be kept within reasonable limits. Development drivages must he on schedule to be ready for the planned opening of new faces, and face ends must keep up with faster moving faces.

Jan 8, 1981

By E. D. Seymour

Minera Yanacocha operates a complex heap leach gold facility in the Northern Andes of Peru. Four leach pads and thirteen solution storage process ponds form an extremely complex system. Distinctly different wet season and dry season rainfall accumulations present unique challenges to the process water balance. Minera Yanacocha operates four excess water treatment facilities which discharge water to the environment at specific quality standards in order to maintain a balanced system. Numerous government agencies and non-government organizations are involved with the permitting, monitoring and control of the discharged water. Minera Yanacocha maintains a relationship with 65 villages and communities, with a population of approximately 29,000 people and the city of Cajamarca with approximately 100,000 residents. This paper provides a high level review of the system complexity, the water balance, the excess water treatment facilities and social aspects of solution management.

Jan 1, 2004

By James E. Monsees

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt. Differences in the geologic media and settings of the prospective sites influence the excavation method in terms of drift length, size of opening, drift slope, rock quality, and boreability. Support requirements, ventilation, and the ability of the geologic system to retard radionuclide migration are also directly impacted by the geology and excavation method.

Jan 1, 1987

By S. R. Rao, J. A. Finch, E. El-Ammouri, K. Ngoviky, P. A. Disten

Sludges produced by lime treatment of acid mine drainage (AMD) can contain significant quantities of base metals which represent both a potential hazard and a loss of values. A new technique for metal recovery from sludge is proposed by combining selective acid leaching and adsorption of metal ions by activated silica sol. The process is demonstrated on two AMD sludges, one containing primarily nickel and the second zinc. They were first treated with sulphuric acid (pH 3.5) to selectively leach the target metals and then activated silica sol was added to the leach solution to adsorb the nickel and zinc. Thickening and centrifuging gave about 90 percent rejection of the input volume to effluent. The adsorbed metals were redissolved by strong acid into a concentrated solution relative to the feed and the silica sol was recycled.

Jan 1, 2000