Search Documents

By Y. H. Kim

A simulation procedure has been developed that realistically portrays aggregate growth and disintegration for particular types of floc structures in water and wastewater treatment processes. The procedure requires local dissipation rates and specification of an interaction distance between colliding particles. A principal difficulty encountered in polymer flocculation, however, arises from changes in conformation of adsorbed macromolecules. Therefore, in systems where polymer flocculation occurs by bridging, dynamic changes in the particle size distribution depend upon the interaction of nonlinear. stochastic hydrodynamics with particles whose growth results from a number of concurrent and sequential random processes.

Jan 1, 1988

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987

By Frederick J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for the coal industry — particularly in Asia — the power plants being planned or under construction are designed to use coal as fuel. This has produced a significant increase in the demand for steam coal that, in turn, has encouraged many in the industry to develop new coal mines. Indonesia is a country that has enjoyed substantial growth in coal production. This developing country has 195 million people who live on the nearly 13,000 islands. It has quickly emerged as the third-largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface-mining methods.

Jan 1, 1996

By Robert P. Edwards, Brian C. Flintoff

Crushing plants (multiple stage) are an integral part of most conventional comminution circuits (ball mill, rod mill - ball mill). Although conventional circuitry is now the design exception, there are still many older, and some newer plants that include crushing in the process flowsheet. In most of these installations the operating objective is to maximize throughput at some minimum product size, in an effort to balance the comminution load between crushing and grinding. To achieve this goal, while avoiding production losses due to overloads, generally requires the use of automatic control strategies. This paper reviews the crushing plant control problem and describes several approaches that have been successfully implemented in different plants.

Jan 1, 1992

By Brian W. Hester

All gold occurrences in Tanzania are of Precambrian age and in geological settings similar to gold deposits in other parts the world. The three main areas of interest are perhaps the least prospected of areas of gold mineralization in Precambrian rocks in non- aligned, or market economy nations. Historic production exceeds 77.660 kg (2.5 million oz). Current results by small scale workers go unreported, but have been estimated to be as high as 11.000 kg (350.000 oz) annually. Gold occurs in both lower and upper Precambrian rocks. In the older. gold is associated with greenstones and iron formations typical of many cratonic areas of Precambrian age. The Tanzanian Craton lies in the north west quarter of the country where it is flanked on both east and west sides by mobile belts involving upper Precambrian rocks of high metamorphic grade. Gold occurs in fractures in the western belt within two distinct areas.

Jan 1, 1989

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985

By Owen Kreilis

By the time coal was discovered in Newcastle, Australia in 1791, it was already a most important industrial commodity in European countries. Coal was the first mineral to be discovered in Australia and the first to be mined. Today, coal remains Australia's most important mineral in terms of local use and international trade. The first mechanized longwall in Australia began operation in 1963. It contained self-advancing hydraulic supports and was installed at Coalcliff Colliery, located in the Southern Coalfields of New South Wales. After nine months and production of 53 kt (58,000 st), the unit was withdrawn, largely because of uncontrollable roof weight and with the problems of airborne dust and large coal still unsolved. Basically, roof support was insufficient. The European design of the Coalcliff longwall was inadequate for Australian conditions. Another type of support with modifications was installed and began operation at Kemira Colliery at Wollongong, New South Wales, in 1964.

Jan 1, 1995

By C. Ottergren

A process does not have higher capacity than what can pass through its bottleneck. Acknowledging this, and with the goal to optimize production at a minimum investment, one can use existing equipment, modify the process flow and make a few strategic capital investments. Automatic setting regulation is a technology that allows balanced crusher performance matching minute changes in feed material characteristics. The system makes it possible to utilize the crushers fully at all times. It also continuously and completely compensates for manganese liner wear.

Jan 1, 1999

By John W. Critchfield

This paper presents an overview of some of the basic issues related to tunnel construction in the presence of flammable and toxic strata gases. Gas properties and possible sources are outlined for the various gases that are commonly encountered underground. Assessment of potential gas hazards prior to construction is discussed. Measures for mitigating the problem during construction are summarized. This RETC Session on Gassy Ground has been organized by the Underground Technology Research Council (UTRC), Technical Committee on Gassy Tunnels.

Jan 1, 1985

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By R. W. Smith, A. Raichur, M. Misra, I. A. H. Schneider

The concept of microorganisms as chemical reagents (flocculants, flotation modifiers and flotation collectors) is quite new. Potential uses for microorganisms include their use in place of certain conventional flotation reagents and as flocculating agents in minerals engineering processes. In addition, in some studies micro-organisms have been used to modify mineral surfaces and, thus, the flotation or flocculation of the minerals.

Jan 1, 1995

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

"Above ground, elevated belt conveyors that span more than 200 m (656 ft) between support points can cross valleys, rivers, forests and buildings with a minimal footprint. The cable bridge conveyor (CBC) is a new type of suspension bridge based belt conveyor system that has long spans between support points. It combines a typical belt conveyor and an improved simple suspension bridge to form a conveyor bridge. The improved simple suspension bridge places a widened bridge deck directly on suspended cables, without the need for high truss towers. The benefits include reduced cost and increase aerodynamic stability compared to conventional suspension bridges. The CBC’s compatibility with current belt conveyors allows versatility in application.A belt conveyor is a ubiquitous material handling system. Conveyors can be placed directly on ground or elevated above ground by support structures. Considerations of cost, design, environment, civil work, safety and process requirements are all factors in choosing the ground-based or elevated conveyors (Zhang, 2014). The ground-based conveyor has the lowest structural cost when the conveyor is placed on an existing road. Maintenance access is easy and straightforward. Compared to the groundbased conveyor, the elevated conveyor can cross existing buildings and structures, give passage to traffic beneath the conveyor, has a smaller footprint and requires less civil work to pass mountainous areas. The drawback of the elevated conveyor is higher structural cost, which can be compared with savings in civil work and other benefits. Conventional elevated conveyors are supported by rigid truss-type structures, with a typical span of 15 to 25 m (50 to 82 ft) between concrete support bents or steel trestles. Triangular truss, using steel pipes instead of hot rolled steel sections, is more efficient. The typical span of a triangular truss-supported conveyor is around 30 to 40 m (100 to 130 ft), while the weight is about 10 percent less than conventional box truss with a shorter span (Jennings, 2013).Long-span elevated structures based on suspension bridge is another step forward in increasing the distance between support bents, reaching 100 to 400 m (330 to 1,312 ft) and beyond. The wide distance between the support points of an elevated conveyor offers unique benefits. The conveyor can cross rivers, valleys, highways, forests and other obstacles with minimal footprint and reduced civil work. The versatility from long-span conveyors makes bulk material transportation over previously impossible terrains now a feasible option."

Jan 1, 2014

By Anthony D. Songer, James E. Diekmann, Jarrett E. Carlson

Computer Aided Design (CAD) systems are currently recognized as a necessary tool for the management of projects. Currently, CAD is used for TBM and conveyor setups, concrete lift design and overall constructability reviews. Typically, such CAD models exist only in 2 dimensions. The advent of more powerful computers, enhanced CAD programs and after market animation packages provides tremendous potential to the Tunneling industry. In particular, effective application of these technologies enhances cost, time and quality in field operations.

Jan 1, 1997

By E. W. Bauman

The important role that mineral aggregates assume today in the construction and chemical industries is best attested to by the astronomical tonnage figures for the annual production of aggregates in the United States as reported by the U. S. Bureau of Mines in their "Minerals Yearbook." For 1965, latest publication available, the tabulation shows a total of 1,716,000,000 tons made up of 30,000,000 slag, 908,000,000 sand and gravel, and 778,000,000 crushed stone. A much more favorable statistical position for slag can be established by listing the world-wide tonnage. According to Dr. A, W. Lee, Director, British Slag Federation, in a paper presented before the 8th Annual conference of the British Institute of Works and Highway Superintendents, he estimates that the probable world consumption of slag is in the order of 100,000,000 tons showing--Great Britain with 10,000,000 tons, Germany, 15,000,000 tons, France, 1$000,000 tons and the United States with 30,000,000 tons. Thus it is seen that the United States accounts for almost one-third of the world's consumption of slag and the 3 west European powers another third.

Jan 1, 1967

By Laura McNally

In 2006 McNally International Inc. in a Joint Venture partnership with Aecon Constructors was the successful bidder on two York Region Tunnel Projects: Bathurst Collector/Langstaff Trunk Sewers; and YDSS Interceptor Sewer 19th Avenue Project. These projects comprise a total of 13 kilometres of 2.74 meter finished diameter tunnels and are both part of the York Durham Sewer System (YDSS). Both contracts require the use of EPB tunnel boring machines with a precast concrete segmental liner. The following provides an overview the two projects.

Jan 1, 2008

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979

By W. J. Cieslewicz

Geologically, northeastern Siberia is a region occupied by a folded belt of Triassic and Jurassic sediments and volcanics. Gold mineralization is of Upper Jurassic age. Most of the stream placers formed during the Quaternary. Placer gold was first discovered in 1916. Between 1930 and 1957, mining was carried out by the "Dal 'stroi," a Russian concentration camp organization. Since 1966, the mines have been worked mechanically. About 10 mining districts are now active, producing, altogether, 110 to 135 t (120 to 150 st) of gold annually.

Jan 1, 1987

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By L. W. Cope

Cuba is a mineral rich area, and the Cuban government is encouraging mining investment in the country. Joint ventures with government entities are encouraged. This paper will give some insights into the laws and regulations, and the agencies to contact for investment and development. The present-day situation of the US sanctions against Cuba will be covered.

Jan 1, 2004