Search Documents

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By Allan E. Hall, Kuda R. Mutama

Jet fan (ductless fan) ventilation in underground mines and tunnels is a subject requiring further attention. At present there are no accepted procedures or guidelines for this type of ventilation. The main reason has been the absence of sufficient general data, which has hampered the development of rules. There is great potential for using jet fans in terms of both effectiveness and economics because they eliminate the need for ventilation tubing. In the present studies a procedure is described and results are presented from a jet fan modeled in a square section wind tunnel. The major purpose of the studies was to provide fundamental data on jet fan performance after it was realized that previous work had been limited and too site specific. The jet fan position in relation to the tunnel walls was varied in order to study the influence of confining walls on entrainment rates and the resulting aerodynamics. A clearer understanding of the fundamental principles of jet fan applications was obtained.

Jan 1, 1995

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By K. L. Johnson

Networks of monitoring wells were established prior to mining at four longwall mine sites in the Appalachians to monitor the effect of mining on water levels, water quality and well yield. Two of the sites were located in stream valleys and the other two sites were located on hilltops. The depth to the mined seam ranged from 500-850 feet with the deeper cover being associated with the hilltop sites. Maximum declines in groundwater levels during and after mining were an order of magnitude less in the stream valley aquifers than in the hilltop aquifers. However, water levels in hilltop wells located outside the area immediately above the panel were unaffected. Water quality changes in wells as a result of longwall mining were negligible at all four sites. Increases in aquifer transmissivity and well yield were much more pronounced in the stream valley aquifers than in the hilltop aquifers. The significantly larger recharge area for the stream valley aquifers than that for the hilltop aquifers may partially account for the differing responses of these two classes of aquifers to longwall mining. These observations appear to be consistent with the stress-relief fracture model for Appalachian Plateau groundwater hydrology proposed by Wyrick and Borchers in 1981.

Jan 1, 1986

By William B. Thayer, James H. Meinholz

The Milwaukee Metropolitan Sewerage District (MMSD) has been working since mid-1977 on a fast track to meet a court-imposed schedule to rehabilitate a large wastewater collection and treatment system at an estimated cost of $1.7 billion. Because of glaciation, the Milwaukee area has an extremely complex geologic environment. The rock surface ranges from outcroppings in the northern and western parts of the area to 76 m (250 ft) below the surface at the mouth of the Milwaukee and Menomonee Rivers. Bedrock beneath the glacial mantle is a thick sequence of early to middle Paleozoic sedimentary rock. To cope with the many complexities of this large public works project, a Program Management Office (PMO) concept has been employed. A Geotechnical Engineering Group was established within the PMO to provide a continuous , unified approach to geotechnical engineering and full disclosure of all geotechnical information in the construction contract documents. It provides qeotechnical engineering to design and construction, develops and maintains a qeotechnical data base, and participates on the claims resource team.

Jan 1, 1983

By J. W. Hawkins, K. B. C. Brady, K. Miller, J. Cuddeback

Remining of abandoned coal mines in Pennsylvania requires the implementation of pollution abatement and mining techniques called Best Management Practices (BMPs). Water-quality data from over 100 remining sites with more than 230 abandoned discharges were analyzed with respect to the types of BMPs employed to abate the pollution loadings of acidity, iron, manganese, aluminum and sulfate. Discharges exhibiting a significant decrease in acidity were most highly associated with sites where large volumes of alkaline materials were encountered (66.7%) or added (63.7%). The best results for iron loading were achieved with large-quantity alkaline addition (54.6%) and water handling systems (47.8%). Water handling systems (47.4%), daylighting (40.7%), and revegetation (40.2%) were associated with significantly lower manganese loadings. The decreases in acidity and sulfate loads associated with increasing the amount of alkaline material in the backfill indicates that the production of acid mine drainage can be retarded by adding large quantities of alkaline materials.

Jan 1, 2002

By W. Petruk, D. B. Sikka

Lithium-bearing lepidolites from three deposits in the province of Goias, Brazil, were investigated to determine whether there is a correlution between the lithium content of the mineral and the color of lepidolite and associated tourmaline. Such a correlation can be a useful guide to field geologists for outlining high-grade lithium ore zones. It was found that mauve-pink lepidolite associated with pink tour-maline, and brownish lepidolite associated with black tourmaline have high lithium contents, but that the color of lepidolite is not due to lithium. The pink color of lepidolite and tourmaline is likely due to Mn3+, and the brownish tint of lepidolite and black color of tourmaline to Fe3+. Lepidolites appear to be lithium- rich when the lepidolite and associated tourmaline contain relatively high amounts of Mn3+ and/or Fe3+.

Jan 1, 1988

By J. F. T. Agapito, J. B. Page

This paper describes part of a geotechnical study based on stress determinations and convergence measurements conducted to assess the long-term stability of an experimental room-and-pillar oil shale mine. A rock mechanics program was initiated in 1971 at the Colony Mine as part of a large study conducted for the design of a commercial operation. The Colony Development Operation is a joint venture currently consisting of four active members; Ashland Oil Inc., Atlantic Richfield Company (Operator of the project), Shell Oil Company, and The Oil Shale Corporation. Although oil shale commercialization plans are presently suspended, rock mechanics instrumentation has been continued as part of Colony's policy in maintaining readiness to proceed with a commercial shale oil plant when national energy policies became better defined. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 200 miles west of Denver. Experimental mining operations were conducted from 1965 to 1972 with one of the major objectives of the pilot mine being the assessment of opening and pillar sizes for the determination of extraction ratio and life of the property. Mining was conducted in a 60 foot thick portion of the Mahogany Zone in the Parachute Creek Member of the Green River Formation, at depths of 600 to 850 feet by a one-bench system. Pillar dimensions were 58 feet by 58 feet and rooms were 55 feet wide.

Jan 1, 1977

By G. Brofas

Mt Giona situated in the floristic hot-spot of southern-central Greece has an especially rich flora that counts more than 1000 native vascular plant taxa (species and subspecies) and an important plant endemism that is estimated to be about 10% of the native flora. The danger of population reduction of rare and endemic plant species and the opportunity to use rare native species in rehabilitation projects are two different aspects of rehabilitation planning in Mt Giona. In this study, an inventory of rare and endemic species of the area, their classification into IUCN threatened categories and an estimation of their habitats vulnerability are provided. The results emphasize the necessity to develop a monitoring program to analyze population viability of certain threatened plant species. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed. An inventory of the species that have colonized the mining spoils was also undertaken. Twelve of them are endemics. Seven native species, because of their biological and ecological features, were selected for rehabilitation purposes of disturbed areas by mining activities. Seed germination, aspects of their reproductive biology and seedling emergence after sowing in pots under field conditions were studied. The seed germination study in the laboratory led to the identification of the optimum germination conditions and the creation of germination protocol for each species. Seedling emergence depends on the sowing season and the mulching. The use of the above species is recommended for rehabilitation purposes. The creation of artificial micro-reserves on calcareous spoils derived from bauxite mining for the conservation of water-stress tolerant rare and endemic plants is also proposed.

Jan 1, 2007

By Roussos Dimitrakopoulos, Liam Findlay

Semimobile in-pit crushing and conveying (IPCC) systems can help reduce truck haulage in openpit mines by bringing the crusher closer to the excavation areas. Optimizing a production schedule with semimobile IPCC requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout and truck fleet investment decisions. A mining complex with multiple mines and IPCC systems should be optimized simultaneously to find an optimal schedule for the entire value chain. An integrated stochastic optimization framework is proposed to produce long-term production schedules for mining complexes using multiple semimobile IPCC systems. The optimization model has flexibility to select the crusher locations and conveyor routes from anywhere inside the pits. The framework uses simulated orebody realizations to consider multielement grade uncertainty and manage associated risk. A hybrid metaheuristic solution approach based on simulated annealing and evolutionary algorithms is implemented. The method is demonstrated using an iron ore mining complex

Nov 1, 2024

By Jr. Cook

Panned stream-sediment,geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial gravels of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa counties, Alabama, and Baldwin and Hancock counties, Georgia. Identification of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1988

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By K. E. Kolm, W. H. Langer

Developing natural aggregate resources (sand, gravel, and stone) creates environmental impacts. A systems analysis method has been designed to characterize the components of the environmental system, identify potential impacts to those systems, and evaluate the extent of those impacts. The step-wise method consists of problem definition, data collection, preliminary conceptualization and characterization, additional data collection, data analysis, and refinement. The method requires analyzes of various systems making up the environment, including land surface, geomorphic, subsurface, and groundwater systems. After system characterization is complete, the method focuses on identifying and evaluating potential environmental impacts to determine acceptable mining strategies.

Jan 1, 2001

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By T. H. Chan

As the University of Hong Kong and their advisors planned their new Centennial Campus it became clear that they would have to re-provide existing water reservoirs on an adjacent site with new salt water reservoirs located underground in two new caverns. The existing reservoirs are owned by the Water Supplies Department who provide salt water for sanitary flushing and a separate potable water supply for regular use. Although underground reservoirs had not previously been adopted locally, the planning has been completed to a tight schedule and the construction is well advanced. The need to preserve historic buildings imposed constraints, as did the requirement to minimise potential construction nuisance for the local community and environment. This paper presents the background to the project and the work carried out to develop an innovative, sustainable and environmental acceptable solution. Construction progress to date is also presented.

A thermomechanistic model was developed for the thermal decomposition of the enargite contained in a copper concentrate at 650° to 750°C in a fluidized bed with an inert atmosphere. At the particle level, the model permits one to predict the thermal profile inside the reacting enargite particles, as well as their thermal cycle. At the macroscopic level, a population-based model coupled to the bubbling-bed fluidized bed model allows one to predict the fractional conversion (dearsenification) of an enargite-bearing copper concentrate.

Jan 1, 2002

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By K. Pietruszka

The article presents the concept of the application of the Finite Element Method (FEM) and ABAQUS software in the global monitoring of changes in the rock mass and on the surface of the area, as a result of backfilling the workings. Waste materials applied for stabilizing old mining workings can have a strong influence on the rock mass and surface. According to the regulations, this process should be carefully monitored, especially in terms of the safety of surface structures and rock mass stability. The article presents the concept of an analytic and graphic presentation of the results of the measurements of old workings, applying the Finite Element Method and ABAQUS software in model studies. The main purpose of such interpretation of the geodetic observations results is the application of methods providing wide possibilities to present the geometry of workings, their changes and the influence of the rock mass and surface.

Jan 1, 2008