Search Documents

By Levent Ozdemir, Charles Merguerian

Between 1996 and 1999, a high-performance Robbins TBM [235-282] excavated a 5 mile long, 23´2? wide, and ~700´ deep tunnel through the subsurface of southwestern Queens. Low penetration rates (~6´/hr [actual] vs. ~9´/hr [anticipated])resulted from changed rock mass conditions mostly attributable to high-grade metamorphism of the rocks. Over a three-year period, as-built circumferential geologic mapping (scale 1?=10´) and digital imagery of the tunnel, fracture and fault analysis, structural, lithologic, and petrographic studies have shown that the rocks of the Queens Tunnel consist of orthogneiss of mesocratic, leucocratic, and mafic composition. These metaigneous rocks developed coarse-grained fabrics during Grenvillian (~1.0 Ga) granulite facies metamorphism, and retained their nearly anhydrous, poorly foliated character during subsequent high-grade Ordoviciande formation. Lacking a penetrative foliation, the coarse granoblastic rock texture and extraordinary garnet content (up to 50% in some zones) together proved animpediment to efficient chip production and resulted in bimodal production of blocks and excessive fines. TBM excavation of the Queens Tunnel was also hindered by geological conditions that included unexpected lithology and rock fabric orientation, a zone of crosscutting hypabyssal rhyodacite dikes, and unanticipated extent of brittle faults. The dikes and brittle faults produced blocky ground conditions and a collapsing face condition that produced cutter damage and decreased utilization. Such fundamental textural, mineralogic, and lithologic control over hard-rock TBM penetration can be predicted by careful pre-bid geological analysis. To determine the causes of lower than anticipated TBM performance, a detailed investigation was carried out that included analysis of operational data from the TBM data logger and an extensive laboratory test program on cores retrieved from tunnel walls. Integrated laboratory testing included punch, point load, tensile strength, Cerchar abrasivity, and linear cutting tests, independent petrographic analysis and machine performance analysis. These allied investigations have provided quantification that the rock mass exhibited an unusually high degree of toughness and rock directional properties and established geological causes for decreased TBM penetration rates.

Jan 1, 2003

By G. G. O. O. Uwadiale

Starting from a crude ore assaying 45.6% Fe, a fine-grained oolitic iron ore was concentrated by the oil agglomeration technique to 90% Fe recovery and 65% Fe assay. The ore required grinding to minus 5 µm to effect adequate liberation, and the technique yielded optimum results at pH 9. The roles of pH, collector, and bridging liquid concentrations on selectivity and yield of iron minerals in the concentrates are discussed.

Jan 1, 1991

By E. Harrison

The Greens Creek Ore Bodies are located approximately 18 miles southwest of Juneau, Alaska in an area on Admiralty Island classified as a non-wilderness national monument. An area-wide stream sediment geochemistry program targeted the deposit in October of 1973. Today, after 37,000 meters of combined surface and underground diamond drilling, three ore zones are known to exist with total reserves approaching 4.1 million tonnes. Lying within moderately folded metasediments of an undetermined age, these orebodies are thought to be of seafloor exhalite orgin and contain unusual and impressive amounts of gold, silver, lead, zinc and copper.

Jan 1, 1986

By Pertti Koivistoinen

There are many grinding schools in the mining world, which claim their grinding method to be the best possible - and still the methods concerned vary a great deal. Some of them have multi- stage crushing and only single stage grinding while in others crushing may be nominal, but grinding can be very complicated. - In this presentation firstly the nine most common comminution circuits will be analyzed. Then results from a pilot scale test series will be reviewed, in which nickel ore ground by four different comminution methods was fed to a common flotation treatment.

Jan 1, 1995

Collaboration between education providers is the key to long-term sustainability and improved quality in mining education. The mining industry is now, more than ever, an industry doing business on a global basis. Staff are recruited by global mining companies in many different countries and can find themselves deployed anywhere in the world. The mining engineer of tomorrow must be willing to take on this international challenge, and must be educated to a level where he or she has a comprehensive grounding in technical aspects of mining engineering, but also a well-founded appreciation of management, social, environmental and cultural issues that may be encountered around the world. In order to deliver such an education, academic providers must collaborate at both a national and international level. This paper provides an overview of progress that has been made in Australia through the national joint venture ? Min¬ing Education Australia (MEA). Supported by the mining industry in Australia, through the Minerals Council of Australia (MCA), MEA has been operational since 2007 and is seeing the development of a range of innovative courses and delivery methods, together with a high level of staff cooperation across the country. MEA has also commenced some international teaching initiatives that are seen as a catalyst for a far greater degree of international collaboration in the future. Such activity is not only to the benefit of the students who are taught by experts from around the world, but it also ensures that individual univer¬sity programs remain viable in terms of staffing numbers and financial performance. The paper also presents some statistics on recent upward trends in mining engineering student numbers from around the world, in response to the global shortage of mining engineers.

Jan 2, 2010

By J. P. Hedlund

Molycorp's gravity type panel-caving operation employs a system of short raises to transfer ore from the Grizzly Level to the Haulage Level. The raises have normally been developed using a conventional drill-and-blast method or a combination conventional/raiseboring method. A new method was needed that would be less labor intensive, provide a safer work environment for personnel, provide a stable raise that could be self-supporting and a method that would be cost competitive with the conventional system.

Jan 1, 1991

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By Lancelot E. Kun

The high-rate floc blanket clarification process developed by the Anglo American Corporation of South Africa is capable of continuously clarifying gold and uranium pregnant solutions containing 200-2500 mg/L suspended solids to below 25 mg/L solids at an average rising velocity of 8 m/h at the low process cost of R0,001-0,002 per ton of liquid treated. Overall process cost savings are mainly due to increased polishing filtration cycle times.

Jan 1, 1984

By Jean-Luc Cornet

As modern conveyors are increasing in size and complexity, their control requirements are becoming more and more critical. In addition to the safety and equipment protection requirements, control systems are now called to implement intelligent drive controls derived from dynamic analysis modelling, as well as to provide fast and accurate diagnostics while keeping operator controls simple. These requirements led to the development of a new and innovative approach to control system development. This paper describes the control philosophy used by Conveyor Dynamics, Inc. (CDI) and some of the key features of our approach to the architecture of control systems.

Jan 1, 1993

By Daniel R. Hack

Spatial relationships among physical 'and chemical properties pertinent to economic development of sand and gravel deposits have been little studied. Models need to address trends or zonation of material properties applicable to mine evaluation and planning or as a guide among deposits for use in regional assessment Models can then be utilized to design sampling programs to optimize additional data acquisition. Development of a preliminary methodology in the lower Boise River Valley, western Idaho, will utilize historical and recent data from a terrace-gravel deposit. Classical statistics and techniques of spatial data analysis will be evaluated as a precursor to formal geostatistical evaluation.

Jan 1, 2002

By J. C. Weimer

The goal of Bethlehem's mining research program is to improve both the safety and productivity of our mines through the use of new equipment, new technology and new mining methods. Although we can all agree on the value of such goals, achieving them can be a costly, time-consuming and sometimes frustrating experience. However, the potential benefits of lower costs per ton and better safety in an increasingly more stringent and confusing regulatory environment make the expended effort worthwhile. At Bethlehem we feel that the mining companies are in the best position to determine the needs of the industry, and coal companies have the incentive as well as mine sites at their disposal for testing. Therefore, the mining industry should be leading the research effort

Jan 1, 1979

By R. G. Reddy, A. E. Torma

Bio-treatment of uranium contaminated soils from Fernald using the bacterium Thiobacillus ferrooxidans was investigated. The experimental results showed that extraction of uranium upto 99 percent from soils were obtained with 10 percent pulp density suspension and with addition of iron (3000 mg/l) after bio-remediation time of seven days. Application of the results to industrial practices is discussed.

Jan 1, 1995

By Harold J. Bennett

The Minerals Availability Program is a Bureau of Mines Program to systematically measure and classify identified worldwide nonfuel mineral resources according to their respective extraction technology, economics, and commercial availability. The program is designed to identify, collect, compile, and evaluate information on worldwide active mines as well as on developed and explored mineral deposits, and on mineral processing plants. Objectives are to classify domestic and foreign resources, to identify by cost evaluations resources that are reserves, and to prepare analyses of the availability of these resources for 34 commodities and secondary minerals. Availability analyses consider such factors as geographic location, the type of producible material, the technology and time required to produce a marketable product, and the productive capacity and unit cost for each deposit. These factors, reflected in the aggregated tabular and graphical data in the study for each commodity, are developed for consideration in the formulation of both domestic and foreign mineral policy. To date, the data have been collected for the 34 commodities and the availability analyses are in various stages of completion; expected first cycle completion date for all 34 is early 1986. Raw and aggregated data are available to the public in the form of computer-generated listings, tapes, and maps as well as in published reports. Also, systems developed to assist in performing the engineering and economic c analyses, including the computerized economic evaluation program (MINSIM) and the cost estimating system (CES), are available.

Jan 1, 1984

By John Jonkman

Many companies in the mining and minerals processing industry are finding themselves in the transition stage from the Industrial Age to the Information Age and are trying to become prepared for the Knowledge Age. To remain competitive in the decades ahead, they are faced with integrating the enterprise through the use of computers and networks. This paper discusses some common human and organizational barriers to enter- prise integration. It proposes how to develop the organizational and human' networks to match the capabilities of the technical networks which are being' implemented. Ten practical considerations are then presented for consideration in the executive suite in addressing the human side of implementing the computer integrated enterprise.

Jan 1, 1989

By Bruce Kennedy, Dan Nilsson

Mining means drilling and blasting in order to break down the rock, loading and transport, and often also crushing the ore down to a suitable size. These operations can be done in open pits or in underground mines, and also, to a lesser extent, in marine mining. The same operations are also used in various types of construction, i.e., for roads, water power stations, etc. Before beginning a detailed economic analysis of the factors which enter into deciding whether to mine by open-pit or underground mining, and at what point a change should be made from open-pit to underground mining, or vice versa, it is of interest to consider some general factors.

Jan 1, 1982

By Douglas R. Malicoat, Christopher J. Pritchard

Tg Soda Ash operates an underground trona mine located In southwestern Wyoming, which utilizes continuous mining machinery to produce 2.OM tpy (2.2M stpy) by shortwall and room and pillar methods. As the mine developed, the Increasing distance from the shafts caused travel times to be a significant factor in planning for mine emergencies. It was decided to construct a barricade chamber, a modified refuge chamber, to Increase safety and to provide an additional escape option in the case of a mine emergency. Fortunately, there has been no need to use these facilities during the last 9 years, but mine emergency planning has been greatly improved.

Jan 1, 1993

By Atmesh K. Sinha

The market for thermal coal has recently been growing rapidly and it is projected to continue to do so in the foreseeable future. Both the national and international markets often demand high Btu low sulfur thermal coal in order to minimize the cost of utilization and meet the environmental restrictions. High quality thermal coal can be prepared to compete in the utility market by desulfurizing the high Btu midwestern coal and blending it with low sulfur western coal which is usually low in Btu content. The methods that can be used for optimizing the coal preparation plant operating parameters for physically desulfurizing coal is presented.

Jan 1, 1984

By L. John Minnick

A revised and expanded edition of a previous paper** dealing with reactions of calcium and magnesium oxides and hydroxides with pulverized coal fly ash is presented. Lime-fly ash specimens were cured at constant temperature and subjected to X-ray diffractometry, differential thermal analysis, pozzolanic reactivity tests, and microscopical investigations. Bars of limefly ash were subjected to cycles of wetting and drying, and measurements of length change were recorded. A discussion of variations within and among types of lime and types of fly ash is presented. The nature of the pozzolanic reaction is reviewed, particularly as related to compounds which are used up and formed during the aging process. The relationship between the pozzolanic reaction and the resultant physical properties of the mixtures is examined.

Jan 1, 1968

By R. E. Coleman

Infrared spectroscopy, employing the internal reflection method in conjunction with solvent extraction techniques, was used to study surface reactions between aqueous potassium ethyl xanthate and both sphalerite and precipitated zinc sulfide each activated with aqueous copper sulfate. It was determined that reactions occurring on the sphalerite and zinc sulfide surfaces produce the reaction products ethyl dixanthogen and cuprous ethyl xanthate, some of which are ad¬sorbed on the mineral surfaces. According to infrared spectra showing the reaction to form these compounds, the ratio of cuprous ethyl xanthate to ethyl dixanthogen adsorbed is directly related to pH of the flotation solution.

Jan 1, 1967

By H. Melama

The primary grinding stage in the Vuonos concentrator comprises a rod mill in open circuit and a semi-autogeneous mill in closed, circuit with a hydrocyclone classifier. The instrumentation of the grinding circuit is displayed in Fig. 1. All the measurements have computer interfaces and all the control circuits have been implemented by the process control computer. The crushed ore feed to the rod mill is measured by a belt-weigher and controlled by a belt-feeder. The pulp density in the rod mill is stabilized by proportioning the waterfeed at the mill inlet to the crushed ore feed. The slurry level in the pump sump is measured by a pressure transducer and it is controlled by charging the speed of the direct-current drive pump.

Jan 1, 1984