Search Documents

By Anis Farah, Khosrow Aref

Pull-out tests were conducted on cable bolts grouted with concrete, and cement paste. The influence of several parameters on the performance of these cables were studied under loading rates varying from very slow to relatively fast. These parameters include water-cement ratio, cable surface conditions, curing time and embedded length. In addition to being more economical, the results indicate that cables grouted with concrete have higher ductility and ultimate bond strength as compared to those with cement paste only.

Jan 1, 1986

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By J. Peshel

This paper presents a regulatory perspective of the design and construction of the Exploratory Shaft Facility which may become part of the future high-level waste repository. Site characterization concerns and long-term waste isolation concerns require the consideration of various shaft design and construction aspects quite different from that of conventional shaft sinking.

Jan 1, 1989

By F. Seymour

A dynamic programming algorithm is presented that takes a series of nested phases, a fixed mining rate schedule, a fixed plant production capacity schedule, and finds the mining and cutoff grade sequence that maximizes the Net Present Value. This tool allows the Mining Engineer to quickly look at project sensitivity to various production capacities, commodity prices, and costs. A description of the algorithm is given along with examples of how it has been used at Newmont.

Jan 1, 1995

By Anitava Ghosh

A computer program has been written to simulate ground vibrations induced by multiple- hole surface blasts. The program is an inexpensive and relatively easy to use tool for predicting the principal blast vibration characteristics that determine damage and annoyance potential: peak particle velocity, frequency content and pulse duration. The program generates a complete ground motion history by superposing, at any surface position, the vibrations induced by each individual explosive charge. It requires specification of (hence allows accounting for) the blast geometry, initiation sequence (including random delays), position with respect to blast, pulse characteristics induced by each charge, and propagation laws. A methodology is outlined to determine the necessary variables either on the basis of site investigations (e.g.,velocity, attenuation, single-hole input pulse), or by back-calculation from measured blast vibration records. The latter procedure has been applied to blasts from two coal strip mines. Main difficulties encountered are backcalculating individual input pulses, propagation (especially dispersion) parameters and delays. A normal distribution of delays, based on published results, has been shorn to influence the results and the response of a single degree of freedom structure significantly. Broadening of the wave types included, improved input pulse determination and propagation laws, and more detailed verifications with field results are required in order to make the program more directly applicable to practical situations.

Jan 1, 1986

By Waclaw Dziurzynski, Janusz Tracz, Danny Wooton, Andrzej M. Wala

The purpose of this paper is to present validation studies of the mine-fire simulator using data gathered from an actual mine fire which occurred in November 1991 at the Pattiki Mine. This study evaluates the suitability of the computer software package for modeling underground fires. The paper also discusses the importance of the on-line monitoring system for the validation process.

Jan 1, 1995

Micro-computers have made it practical to install a high-speed acquisition system to collect data from a longwall face in near real-time. By simultaneous data analyses using neural networks and fuzzy sets, information regarding longwall mining performance and underground behavior can be provided and forecasting longwall instability and detecting geological anomalies is feasible. This paper presents details of the application of neural networks and fuzzy sets in developing on-line evaluation of longwall roof behavior. Techniques for interpreting longwall shield pressures and characterizing roof conditions are discussed.

Jan 1, 1996

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By Colin M. Kelly

The Loveridge Mine, located near Fairmont, West Virginia, has been mining coal from the Pittsburgh Seam since 1958. As the mine develops its reserves it finds itself with increasingly distant hauls from the operating faces to the preparation plant. Initially, the mine was designed with track haulage. The coal was hauled to an underground rotary dump which fed a slope belt, to the preparation plant. As the haulage distances increased, production delays due to the track system's limitations became severe. To resolve this situation, a complete review of the haulage system was undertaken. Simulations of the present system along with future scenarios were conducted to help management effectively plan the haulage requirements of the mine for the remainder of its life.

Jan 1, 1986

By Cynthia M. Walck, S. K. Grant, R. D. Hagni

The Post Gold deposit is located in the northern part of the Carlin trend. The mineralization at Post occurs in proximity to a Jurassic-Cretaceous composite stock. Most of the gold at Post is hosted by non-metamorphosed calcareous siltstone and highly altered diorite, adjacent to the low grade skarn. Endoskarn, exoskarn, hornfels and marble are developed outward from the intrusive. The skarn is composed dominantly of diopside, tightly intergrown with gannet, k -feldspar, and sphene. The highest grade gold values are adjacent to the skarn, which acted as a permeability barrier to fluid migration. Post is the first Carlin-type deposit at which a skarn has been recognized to play a significant role in the localization of gold.

Jan 1, 1990

By Charles A. McLean

Bucketline dredges are machines for excavating large relatively unconsolidated or weakly consolidated materials from below water level. They are at the upper end of the capital cost range and the lower end of the operating cost range for placer mining machines and have digging capacities, typically, of from 100 cubic yards of bank measure material per operating hour for a shallow digging dredge carrying 2 cubic foot buckets to 1500 cubic yards per hour for a large deep digging dredge with 33 cubic foot buckets. Bucketline dredges used in the mining industry have their mineral processing plants mounted aboard the digging hull. Since dredges are high capital cost items, they require large ore reserves, typically at least ten years. Because of their high capital cost they are usually operated around the clock and for as many months of the year as weather conditions will permit. Typically a well run dredge operating year round would be expected to operate for 600 hours per month. Dredges operated in cold climates cannot operate when the weather freezes the dredge pond or the gravels, and dredges operating at sea cannot operate when high waves might batter the digging ladder against the bottom or upset the mineral extraction process.

Jan 1, 1992

By V. N. Kelly

The ability to link geological sections on a graphics screen to form three dimensional geology representation was implemented at Kidd Creek in 1987. This technique affords an opportunity to optimize metal estimation in ore at the Kidd Creek copper, zinc and silver mine, by applying enhanced interpretation methods. On a series of geological sections varieties of ore are outlined. These are linked from section to section to form polyhedra which closely simulate the three dimensional shapes of the different ore types referred to as mintypes. The orebodies are divided into zones, referred to as domains, that approximate the function of variograrns, for which' preferential continuity of mineralization has been estimated for distances in the width, strike and dip directions. These distances define ellipsoidal volumes of influence. The domains are also linked into polyhedra. Both types, coded by ore variety and zone, are mapped into the block model. Tonnage and metal values are calculated for ten-foot cubical cells of the block model by any of several estimation methods under domain control. In estimating the metal grades for a cell the predetermined search ellipse is applied to select only those drill hole assays of the same mintype as the cell designation. Once grade estimations have been determined for the cubical cells comprising the model, a wide range of stored information can be viewed. For example, in plan at any row elevation or on vertical section at any azimuth, as either printed values for the cells or as contoured data. This flexibility is of particular value in checking and refining the geological interpretation to better conform to ore types and grades actually mined. Combined with three dimensional geological modelling, and correctly chosen domains, the use of mintypes implants essential geological control into the system and prevents assays for one ore type from affecting grade estimation in adjacent ore types. The three dimensional geological modelling and block model segments provide information which is effectively applied to the stope design, production, planning and control parts of the system.

Jan 1, 1989

By Mark R. Stanton, Douglas B. Yager

Integration and synthesis of mine-site topography, geophysical, and geochemical data yields both two- dimensional and three-Amensional perspective models for the May Day mine located in the Cement Creek drainage near Silverton, Colorado. Induced polarization, geophysical data are spatially registered with geochemical data acquired from drill hole cuttings that are contoured m three-dimensional space, thereby permitting determination of the most metalliferous and sulfur rich zones of a waste pile. This spatial modeling application was developed to be a visually intuitive tool to aid in mine waste reclamation.

Jan 1, 2000

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By C. C. Clark, S. J. Jung

Determining the correct combination of mix components and water for high-density paste backfills that have the transport and deposition properties necessary for a mining operation is a difficult task. Rheologic properties cannot be determined without conducting full-scale pumping tests, and data from existing tests tire very limited. This paper presents the findings of investigations undertaken to determine if paste-backfill rheology can be determined using existing techniques and to determine which mix and system variables have the greatest influence on transport-pressure loss. Data from laboratory-scale pumping tests were used to produce a rheologic model of flow behavior for comparison, and a statistical analysis was conducted to determine the most significant factors affecting transport-pressure loss.

Jan 1, 1996

By W. M. Ma, W. L. Zhong, Syd S. Peng

In a longwall section that consisted of 7 longwall panels, there were two high pressure gas transmission pipelines across the panels burying from 3 to 10 ft. below the surface. One pipeline was 20 in. in diameter while the other was 24 in. in diameter. In order to investigate the stress conditions sustained by the pipelines during underground longwall mining, strain gages were mounted on the pipelines above panel #3, #4, and #5. Survey monuments were also installed along but near the pipelines. This paper presents a subsidence prediction method and the preliminary results of the pipelines' stress conditions as affected by underground longwall mining.

Jan 1, 1986

By Mark W. Springett

The sampling of precious metal deposits entails inherent problems due to the low mineral abundances, high mineral specific gravities, skewed grade distributions and wide ranges of mineral particle sizes. Sampling practices and precautions are discussed with particular attention to each of the tripartite stages of sampling - sample acquisition, sample preparation and sample assaying. Practical examples of approaches to the sampling problem are given and some examples of significant sources of error are provided from gold and silver deposits in North America.

Jan 1, 1992

By D. Malhotra

This paper discusses the need for periodic auditing of mineral processing flowsheets and the potential benefits a company can gain from a study of this nature. A carefully designed flowsheet audit can have a significant impact on the metallurgical performance in the plant. Several case studies illustrating the potential benefits that can be attained from flowsheet auditing of mineral processing plants are discussed.

Jan 1, 1988

By M. Li, J. D. Miller

During the past decade, considerable effort has been made to develop improved flotation strategies for the sedimentary phosphate resources from Florida, particularly the dolomitic phosphate resources. New flotation equipment and alternate flotation strategies have been evaluated. These developments are reviewed for both traditional siliceous resources and future dolomitic resources. Most process strategies involve variation in the reagent sequence and/or the use of depressants/dispersants. Further research and development efforts in flotation technology are needed to increase flotation plant capacity by elimination of the conventional double float process, to improve the recovery of coarse phosphate, and to achieve the desired selectivity with respect to carbonate minerals, particularly dolomite.

Jan 1, 2000