Search Documents

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By H. Peter Knudsen

In most open pit gold mines, ore-waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. This paper focuses on the source of the conditional bias. While it is true that high grades and "outliers" can induce a bias, they may not be the only reason for the persistent bias seen at many mines. In this paper, it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1993

By S. El-Mofty, P. Zhang, N. A. Khalek

This article reviews different technologies used for beneficiation of siliceous and calcareous phosphate ores of different origin. The review sheds light on recent trends suggested for solving problems associated with separation of different impurities from phosphates. Applications of recently modified flowsheets as well as new reagents in the flotation of phosphate ores of sedimentary origin are highlighted.

Jan 1, 2003

By H. C. Verakis, T. E. Lobb

During the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry, with coalmining being the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past several decades. Although blasting accidents usually represent a small percentage of the total number of mining accidents, they continue to occur and the severity of these accidents is disproportionately high compared to the other mining accidents. This paper is an analysis and summary of mine blasting accidents over the past several decades as they relate to surface coal mine operations. A compilation and review of surface mine blasting accidents from1978 through 2001 was made. The accident data was examined to identify the trends and primary causes, which continue to be blast area security, fly rock, premature blast, and misfires. Approximately 46percent of the causes of surface coal mine blasting accidents are attributed to blast area security, while fly rock, premature blast, and misfires represented an additional 50 percent of the causes. Accident categories were established based on the cause of the accident or the activity that was taking place when the accident happened. A discussion of the accident data is presented to increase hazard awareness and to emphasize safe blasting practices and MSHA requirements concerning mine blasting operations.

Jan 1, 2003

By R. J. Pugh

The surface chemical sites on several fillers (quartz, feldspar, calcite and granite) were studied by the adsorption of well defined acid and basic probe molecules (benzoic acid, benzyl alcohol, ethyl benzoate, pyridine and benzyl amine) from cyclohexane. The results provided a wide variation of adsorption data, emphasizing the extensive range of site heterogeneity on the filler surfaces. In addition, it was shown that the acidic probes were strongly adsorbed on all of the minerals, thus indicating that the basic surface sites dominate the acidic ones. Also, through FTIR studies with vapor-phase probes adsorbed on orthoclase, it was possible to identify the nature of specific sites and the type of bonding occurring between the filler surface and the probe molecule. These types of surface analytical techniques could give useful information for predicting the adsorption functional groups on dispersants, dyes, thickeners, etc. and could lead to enhanced interfacial bonding between the filler and the matrix.

Jan 1, 1993

By Andrzej Wala, Waclaw Dziurzynski, Janusz Tracz

Recent advancements in computer hardware have led to the development of new ventilation planning software for PC's. These programs now can be run more quickly and can display their outputs with graphical techniques. Only a few of the existing programs have the capability to display the output data graphically on plotters. Graphical presentation of ventilation simulation data is essential for quick and sure comparisons of alternative analyses. Recently a noticeable growth has occurred in the application of graphics for display and interpretation of the data that have been developed by simulation procedures. The process of mine ventilation network analyses used for planning and design can benefit from this development. The authors describe and present graphics-assisted software that has been developed to work with a mine ventilation simulation program. This software has some of the following features: - graphic editor on screen, - graphical display of output data on screen (EGA, VGA), - graphical display on plotter or printer, - scaling capability (desired part of the entire schematic can be displayed), and - such values as flow, pressure loss, gas concentration for branches, and pressure and elevation at junctions can be presented as labels.

Jan 1, 1991

By G. Deschenes, M. Fulton

The New Britannia Mine processes a qumtz-carbonate gold ore containing 4.63 git Au at a rate of 2,200 tpd. The ore contains approximately 3 .0% arsenopyrite, 2. 7% pyrite and the rest is gangue minerals. Eight to ten percent of the gold is refractory to leaching. Two years ago, New Britannia Mine experienced cyanidation problems. Gold extraction was not stable and occasionally decreased significantly. Preliminary test work, at laboratory scale and in the plant, indicated that lead nitrate addition was beneficial. A laboratory study was initiated to evaluate the level of control of the parmneters (grinding size, dissolved oxygen, pH, free cyanide and lead nitrate) to optimize the efficiency of the process. It was found that lead nitrate addition is required to alleviate the effect of metallic sulphides. This addition causes a significant increase in the gold leaching kinetics and a reduction in the cyanide consumption. The optimum system appeared to be: leaching for 24-30 hours at pH 11.8, 50 git lead nitrate, 250 ppm NaCN and 8 ppm 02. The gold extraction was 89.8% with grinding at 89%-74Fm (leached tail at 0.48 git). Cyanide and lime consumption are 0.40 kglt NaCN and 1.9 kglt respectively. Following the incorporation of lead nitrate, overall gold extraction was increased from 89.2% to 91.1 % but no change was noticed in cyanide consumption. The gross profit is $CDN 988,000 per year.

Jan 1, 1999

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By Saied S. Navid, Michael A. Piepenburg, Richard F. Escandon, Robert C. Lindsay

INTRODUCTION Phase I of the Los Angeles Metro Rail Project, known as MOS-1 (Minimum Operable Segment-1), is the first phase of the 27 km± (17 mi) subway starter line. MOS-1 is currently under construction and involves approximately 6.4 km (4.4 mi) of subway, five stations, yards and shops routed through the downtown area of Los Angeles. The project will form the initial heavy rail backbone of a more extensive light and heavy rail transit system planned for the greater Los Angeles area in the future. Construction Contract A-171 is one of 4 tunnel contracts within MOS-1 and involves construction of twin tunnels running from the downtown metropolitan area west to MacArthur Park. The heavily populated and developed downtown area, potentially gassy ground conditions, and the possibility of undocumented abandoned oil wells in seismically active southern California made the design and construction of Contract A-171 a uniquely interesting project. This paper summarizes the construction history to date (December, 1988) including design geotechnical considerations, tunnel support design, as-built geologic conditions, shield tunneling performance through soft ground, and ground response. The findings presented herein may aid in the design and construction

Jan 1, 1989

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train, the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71 percent — as confirmed by real operational data from the Antapaccay Mine in Peru. It was the first plant worldwide to use gearless drives for both applications.The gearless principleThe principal idea behind a gearless drive system is to reduce the number of components and diversity of parts, especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material.In order to apply this principle of simplification, the components of a conventional drive system are examined. They consist of:• Driven equipment (mill, conveyor, slurry pump).• Components altering the rated speed (gearboxes, girth gear/pinion).• The electric motor.• Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage.• Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation.• The electrical supply system (cables, switchgear, transformers, protection equipment)."

Jan 1, 2015

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995

By C. R. Rinschler, G. R. S. Smith

A high-strength, industrial-grade membrane filter- cloth capable of high flow rates and sub-micrometric particle retention has been developed. A filtration system using this filter- combined with special filtration techniques and using tubular-filters makes possible the filtration of many difficult-to-jilter slurries. Small, discrete, slowly-settling particles are formed into filter cakes that when pulsed of the membrane filter cloth do not redisperse but settle rapidly to form a dense filter under- flow. A positive separation of solids from liquids is obtained.

Jan 1, 1991

By Abbas Zaidi, Betty L. W. Ou

Wastewaters generated during the extraction of gold from the ore can contain a variety of contaminants such as cyanide, heavy metals and arsenic. Proper management of these wastewaters is therefore necessary to minimize the negative impact of gold mining and milling operations on the environment. The Wastewater Technology Centre (WTC),located in Burlington, Ontario, Canada, has been involved in several studies related to the evaluation of various effluent treatment technologies which are relevant to the treatment and proper management of gold mill effluents. These studies have included bench and pilot scale tests, and the evaluation offull-scale systems. Furthermore, the WTC staff developed protocols for cyanide analysis in gold mill effluents, and a mathematical model for predicting the degradation of cyanide in tailings ponds. The information generated by the WTC staff has been referenced in several reports and papers published over the last ten years (Schmidt et.al. 1982, Simovic & Snodgrass 1989, Whittle et.al. 1989, Zaidi et.al. 1989, Zaidi et.al. 1991). Recently, the WTC has started to develop a micro­computer based expert system for use by decision makers in the gold mining industry and relevant government agencies who are involved in process design, process evaluation, costing, evaluation of the best practicable technology, approval of suggested effluent management systems, and so on. This paper presents some relevant background information and a discussion of the latest version of the expert system being developed by the WTC.

Jan 1, 1992

By Hisakazu Matsushita

1. Introduction This is a report on applications of the earth pressure type balanced shield tunneling projects executed under narrow streets on soft alluvial layers in Japan. Japan is a long island country surrounded by the sea. Steep mountain ranges run along the archipelago and numerous rivers originate from the mountains, leaving only limited areas of flat land along the upper and middle reaches of the streams. The majority of cities in Japan are on soft alluvial layers. Alluvium represents an extremely complex soil formation, sections bordering diluvium being characterized by sharp undulations. Various difficulties are therefore encountered in shield tunneling work undertaken in such ground conditions. Particularly, at work sites lying in an unstable, waterbearing layer with high permeability, shield excavation becomes utterly impossible, hampered by large amounts of underground water as well as land collapsing caused by the water. Even when work can somehow be accomplished by using chemical grouting or by lowering ground water level, which require extra expenses and time, undesirable effects such as ground surface settlement are unavoidable in projects undertaken in the past. The newly developed method allows safe and accurate tunnel excavation at normal speed and without giving any adverse effects on buildings above, even under such unstable ground conditions. An outline of this new method was announced at the "International Tunnel Symposium '78" held in Tokyo, and the method has since been employed in a number of tunneling projects in this country. This report provides further data on the new method with reference to some of those projects, explaining how it allows tunnel excavation with

Jan 1, 1979

By P. Chauvet

From a computational point of view calculating a variogram is a perfectly simple operation. For any particular study, we know which variable is to be studied. We also have a good idea of structural parameters which are likely to be important (the scale of the phenomenon, the probable direction of the anisotropy, etc.). Finally, we know the structure of the data file. So we can specify the parameters to be used to calculate the variogram (the distance classes, the angular classes, etc.). This allows us to decide which variogram program is most appropriate (1, 2 or 3 dimensional data, regularly or irregularly spaced, etc. ) . In general, the basic statistics (mean, variance, correlation? etc.) have been calculated beforehand, and so the distribution of the data is already known. Consequently, the choice of the parameter values fed into the variogram is by no means arbitrary. But it must nevertheless be made before the' variogram is calculated. If the resulting variogram is not satisfactory, the whole sequence of operations has to be repeated. Before going on to see how this can be avoided, it is worthwhile having a brief look at the common causes of "unsatisfactory" variograms.

Jan 1, 1982

By J. A. Herbst

Successful transitions from micro- to macro-engineering are the keys to effective technology transfer between research and development organizations and industrial end users. At the same time, it has proven to be one of the most difficult tasks that the minerals industry has had to manage. Typically, developers of fundamental information concerning how mineral processing subsystems work have been academics and government scientists. These are the individuals giving the most important input to micro-engineering models that can benefit industrial operations. Publication is the usual route for "attempting" to transfer this technology to the end users. Unfortunately, with such publications, very little direct communication occurs concerning real industry needs or the future steps required to make the particular micro-engineering model useful. In the past, the industry has relied on in-house R&D groups and plant metallurgists to "translate" publications, to provide useful macro-engineering tools for plant applications. To some extent, engineering companies have also been asked to serve this function. However, these firms have been rather ineffective in this area since their conservative nature has caused them to look rather suspiciously at new technology. This approach to technology transfer has worked, albeit clumsily, for the last several decades. This communication system is now on the verge of total collapse due to conditions of the minerals industry. Mining companies can no longer afford the significant overhead expenses of specialized technical staffs. Universities are finding it extremely difficult to interest US students in mineral engineering programs, and funding for such programs is weak. Faculty members involved in micro-engineering research today tend to focus on pure (non-application-oriented) research.

Jan 1, 1992

By Stephen C. Everett

Why? This is the first question that everyone asks. Why did Renison give away such a valuable asset? What is the problem with Mt Lyell? No doubt this question was asked of Denehurst regarding Woodlawn, MPI at Stawell, Golden Shamrock at Cobar, Western Metals at Cadjebut and Poseidon with the Big Pit. Whilst it is not possible to second guess the rationale behind Renison's strategic withdrawal from an operation that they considered to be uneconomic, the Renison/Mt Lyell deal has certain specific perspectives:

Jan 1, 1995

By Lennart Malmqvist

Decision-making in exploration deals with experience, knowledge, and sometimes faith, but very often financing and profit, mineral resource aspects, employment, and general political ambitions are parts of the scene. At one end of this spectrum, there is the prospector and his decision on the actual project. The exploration business now expands from its pioneering phase for the benefit of a single company to a wider spectrum which includes the benefit of the large mining consortium and a national development program. Its objectives are also to maintain employment and to favor long-term stability in a mining district or a mining company. The prospector then has new aspects and questions to consider such as, what to do in mining districts where there is a shortage of ore resources but there are still useful investments in mines, processing plants, etc. To analyze the exploration process, therefore, seems to be of great importance in a time of rapidly changing conditions. As in other areas of complex decision-making, for example, in the fields of investments, of production, and of the armed forces, computers most certainly have an important role to play in future exploration decision-making systems. However, we must first analyze our own business as closely as possible to find out what kind of information we need, i.e., why we recommend an exploration program as a good or a poor one. An important part of the debate about exploration is the case study. Case studies on exploration are few and most of those written are only about successful exploration programs. Where are the case studies of the failures and the not so successful programs? Every prospector knows that the majority of exploration projects fail. Consequently, the most important experience seems to be hidden in the failures.

Jan 1, 1979

By J. E. Moyle

Introduction In October 1983, Rio Algom Ltd. decided to develop the East Kemptville tin deposit. This decision was the result of intensive geological and metallurgical evaluation work, as well as careful studies of environmental and marketing aspects. The property is located about 54 km (34 miles) northeast of Yarmouth, Nova Scotia, near the village of East Kemptville. Geology The geological setting is a granitic intrusive at the contact with metasediment. The tin mineralization is in the form of cassiterite (SnO2), which is about 80% tin. Sulfides are associated with the deposit containing silver, copper, and zinc, which are recoverable as byproducts. The mineralization is associated with quartz veins and greisen alteration. In the center of the deposit, the zones are so close together they have the appearance of a massive or porphyry type deposit. Ore Reserves The mine plan is based on 56 Mt (62 million st) at 0.165% tin. Up to the ninth year, mill feed will average about 0.2% and lower grade material will be stockpiled. In later years, the average grade will be 0.16% tin. A 0.08% cutoff grade is planned for the entire 17 years of production. East Kemptville is a relatively low grade tin deposit, and only a combination of favorable circumstances has made it economic. • The ore body is situated at, or very close to the surface, permitting mining by open-pit methods at a very low stripping ratio. • The tin occurs in relatively large crystals that allow for good recovery by gravity techniques. • It is ideally located in a well-settled area, with all essential infrastructural requirements already in place. • The positive and cooperative response from various governmental agencies involved are encouraging. Mine Plan The mine plan incorporates an initial pit, followed by three expansions to the ultimate pit. Mining will be at 14 kt/d (15,000 stpd) and will include 9 kt (10,000 st) of ore plus 5 kt (5,500 st) of waste and low grade. After five years, the mining rate will increase to 21 kt/d (27,500 stpd). It is planned to drill vertical 165-mm (6.5-in.) blast holes on a 6-x 6-m (20- x 20-ft) pattern. Bulk slurry explosives will be used to break the rock. Loading will be with hydraulic shovels into 70 t (77 st) haulage trucks. The trucks will deliver the ore to a 13 x 20 m (42 x 65 ft) gyratory crusher, where it will be crushed to 150 mm (6 in.). Secondary and tertiary cone crushers will be used to further crush the ore to 13 mm (0.5 in.). Process Design Tin extraction technology is practically unknown in North America, but Rio Tinto Zinc, which has a 53% ownership in Rio Algom, is involved in tin production in the UK. Rio Algom has used this experience and expertise in metallurgical evaluation work and in tin-related aspects of plant design. Mineralogical and metallurgical test work have been performed, both on laboratory and pilot plant scales. Mineralogical work was done largely in the UK, the laboratory test program was carried out at the Lakefield research facility in Ontario, and pilot plant work was conducted in Australia. This program has resulted in significant improvements in recovery and concentrate grades, over best projections that could be made before this work was carried out. Concentrating Process The concentrator is being designed to process about 9 kt/d (10,000 stpd). The first step is to reduce the size of the ore to -700 µm (-24 mesh) in a rod mill/ball mill grinding circuit. The ball mill will operate in closed circuit with high capacity banana-type screens. The screened product will be deslimed to 30 µm (560 mesh) with cyclones, then passed over the pri-

Jan 4, 1984