Search Documents

By J. A. Herbst, R. Zaragoza

Conventional control schemes in use today are not able to produce satisfactory control when high-frequency disturbances are present in the flotation feed. An advanced model-based control scheme is presented here as a promising solution to this control problem. The main feature of this control scheme is the real time identification of the unknown disturbances in the first few cells of the flotation circuit. This information is used to control the rest of the flotation plant in a feedforward fashion. This control scheme also provides flexibility to meet any metallurgical, economical, or management objective.

Jan 1, 1987

By R. C. Emmett

Gravity sedimentation is one of the most widely used unit operations in mineral processing and hydrometallurgy. Properly selected and operated sedimentation equipment can provide probably the most economical means of concentrating solids or clarifying solutions. Because of the variety of different approaches possible, including the use of modern flocculants, it is easy to overlook the optimum approach in selecting equipment. The different types of sedimentation systems that can be used in the minerals field and the sizing methods that are currently employed will be discussed here. Sedimentation applications usually fall into two areas, clarification or thickening. While the two operations are basically similar, the difference in emphasis (a well-clarified overflow as opposed to a highly concentrated underflow) results in significant differences in testing, equipment design, and operation. Clarifiers may be merely simple settling vessels with no special features, other than ample volume to provide the detention time needed for suspended solids to settle out of the feed slurry. Or, they can be designed to employ elaborate solids-contact techniques utilizing coagulants or flocculants to achieve more rapid clarification through the growth of particle agglomerates. Thickeners also are available in a wide variety of designs, with the main differences concentrated in the design of the raking mechanism. Thickeners operating in series (continuous countercurrent decantation or CCD) are used to recover valuable solution or purify the insoluble solids. Tray thickeners are used for recovering fine particulate solids such as alumina seed, but in other applications have been supplanted largely by unit thickeners or inclined plate units. Thickeners and clarifiers sometimes are used for storage of either solids or overflow liquor, or employed as precipitating reactors, such as in desilication applications. The use of flocculants and coagulants is much more common in modern processing plants, primarily due to the reduction in capital costs rendered possible through the use of these reagents. The terms flocculant and coagulant are often used interchangeably; generally, it is understood that flocculants refer to organic, high molecular weight synthetic or natural polymers which are useful in flocculating most suspended solids, but generally are ineffective on colloidal suspensions. Coagulants refer to chemicals such as those commonly used in water treatment, alum, ferric salts, lime, etc., which are usually far more effective on colloidal solids but cannot achieve the degree of agglomeration that is possible with the polymers. In some cases, both coagulants and flocculants are used in order to achieve optimum results.

Jan 1, 1986

By R. D. Deister

The Buick concentrator represents state-of-the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry, but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries; lead concentrate grade; and reductions realized in reagent consumptions, operating costs, and personnel. A detailed description of the concentrator, along with a history of the process control development and a more in-depth discussion of the control strategies implemented at Buick can be found in the references. (The Buick flowsheet is depicted in Fig. 1).

Jan 1, 1987

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in states such as Virginia. And minable reserves for the Central Appalachian coalfield are challenged by difficult geological, mining and market conditions. To project coal mining longevity in this region, interviews with mining companies were conducted to determine and assess technical and economic factors that affect coal seam minability. This information was ap- plied to seam and coal reserve data developed by state and federal governments. The results were analyzed to determine the effects of various factors on the overall minable coal reserve base.

Jan 1, 1998

By Marcelino Cortina

It is known that underground bituminous coal mining in the Central Asturian Coal Basin (North of Spain) is a complicated task, due basically to the difficult geological conditions: thin and steep Seams with many faults and other disturbances. Therefore, it is not easy to decide what is the most suitable mining method for each of the seams, and problems in making the correct decision are encountered frequently. Because selections in the past have been inadequate an Expert System, ASTURLABOR;hulla, has been designed and will be developed' to provide accurate advice in the mining method selection process. The paper describes the major features of this Expert System and outlines the ASTURLABOR general project, which includes five other mining Expert Systems to complement ASTURLABOR-hulla.

Jan 1, 1989

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By Yannis Faitakis, Brenda M. Wright, Gail Powley, Mark Hamblin, Randy B. Paine

A major problem in the ore extraction process is the high degree of variation in the mix of materials that make up the mined ore. The mix of materials makes it extremely difficult to characterize and predict the behavior of the ore when it is processed. The Quality Production Database (QPD) tool was successfully used in order to predict and transfer information regarding the quality characteristics of the ore being delivered to the extraction and hydrotransport unit operators. This paper describes the use of QPD in the prediction of various ore characteristics at the Syncrude Canada Ltd. processing facility.

Jan 1, 2000

By A. S. Trimble, J. C. Hower

The petrographic composition of sized coal produced through the progressive grinding of a Central Appalachian high-volatile bituminous coal blend was analyzed for multiple sets either by removing fine, -200-mesh, coal after each test iteration or by retaining the fine coal in progressive test fractions. With prolonged grinding, coarser fractions tend to become depleted in vitrinite and vitrinite-rich microl ithotypes, leading to progressively harder-to-grind coal remaining in the oversize, +200-mesh, fractions. The latter trend is shown both by the maceral and microlithotype composition of the coal and by the increased slope and fractal dimension of size frequency distribution, implying an increase in hardness and resistance to grinding of the oversize coal.

Jan 1, 2000

By P. Johnson, G. E. Jones, G. K. Hoffman, C. B. Krueger, J. S. Raugust, M. Wilks, V. T. McLemore

The NMBGMR is slowly converting historical data into a relational database using Microsoft Access 97. The purpose of this database is to provide data on districts, mines, and mills in New Mexico to government agencies, public organizations, industry, and citizens to make informed decisions about resource development, resource management, water supplies, environmental impacts, hazard assessment, and waste disposal. Once the data are entered into the database with locations, the data can easily be converted to GIS format for displaying as different map layers.

Jan 1, 2003

By H. M. von Seebach, M. P. Trubeljal, L. G. Austin

Six US coals and a crystalline quartz were tested in an instrumented laboratory high-pressure grinding rolls machine equipped with 100-mm-diam. rolls. The machine was choke-fed to maximize the capacity. As expected, the specific capacity decreased with increased grinding pressure for each material tested. Among the six coals, there were significant differences in the critical angle of nip, the effective feed porosity and the variation of strain at the gap relative to the grinding pressure. Although a precise correlation was not obtained, the overall effect of these factors was that, at a given grinding pressure, the specific capacity increased as the Hardgrove grindability index of the coal increased. The relationship between the specific capacity and the grinding pressure for a given coal was independent of feed size down to 150 µm. However, smaller feed sizes produced anomalous results, and the flow within the feed hopper was restricted.

Jan 1, 1996

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem. Combined permeability and leaching tests were done in the laboratory on samples of clay bearing ores to evaluate a clay-stabilizing polymer's effectiveness in preventing the problem. Test results indicate that treating the ores with cationic polymers could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability leaching tests. To determine the reasons for the success of the clay stabilizing polymer, clay swelling tests and zeta potential measurements were made on untreated ore samples and on ore samples treated with the cationic polymer. Test results indicate the cationic polymer could reduce the degree of negative charge on fine particles and their tendency to disperse, as well as reduce clay swelling. Test results indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure during leaching, if clays and fines are kept stabilized. This may be done by treating the zone of high fluid velocity near injection wells with cationic polymers.

Jan 1, 1991

By James R. Runkle

Studies in eastern Ohio, northern West Virginia, and southwestern Pennsylvania determined whether subsidence caused by longwall mining influences soil moisture and tree growth. Soil moisture was measured both over new longwall panels and over an unmined control area throughout the growing seasons of 1990, a wet year when the panels were excavated, and 1991, a dry year. No significant effects of mining could be detected. Tree growth was studied in two pairs of woodlots. In each pair, one woodlot was located over a longwall panel excavated about 1980 and the other over an unmined area. Differences in tree growth between mined and unmined areas were neither significant (for most species) nor consistent in direction. The above results imply that if mining does have impacts they are likely to be highly site-specific and localized such as by disruptions of springs or soil slippage.

Jan 1, 1986

By Fathi Habashi

SOLVENT EXTRACI ION involves two operations: 1) Extraction The metal values in the aqueous phase are extracted by agitation with an organic solvent immiscible in that phase. The two phases are then allowed to separate; the aqueous phase is discarded or recycled and the loaded organic phase saved.

Jan 1, 1970

By Alexander I. Feldman, Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

An extensive geotechnical monitoring program was used to assess ground and liner behavior, provide input to a Disputes Review Board, and verify design assumptions during construction of the Mt. Baker Ridge Highway Tunnel along I-90 in Seattle, Washington. The stacked-drift tunnel liner was constructed with twenty-four 2.9 m diameter concrete-filled drifts forming a semi-flexible compression ring, followed by excavation of the 19.4 m diameter soil core. Instrumentation data was used for monitoring hillside stability, liner deflections and loads, impacts on adjacent highway tunnels, for back analyzing soil properties, and for helping to limit construction-induced settlements to about 6 cm.

Jan 1, 1987

By John T. Bartlett

During the last decade, the increasing price of gold has renewed interest in the various metallurgical techniques for recovering precious metals. Much of the recent technology advance has been aimed at low grade deposits resulting in more complex processes and the necessity of tighter economic control. These factors along with more stringent environmental constraints have made it necessary to optimize each process to minimize energy and raw material consumption and reduce waste discharge. In most cases, detailed process analysis is required to detect inefficiencies and provide alternative solutions for process improvement. Also during this same period, the computer has become widely accepted and computerized mathematical modeling has been applied to an increasingly broader range of problems. Microcomputer based process modeling and simulation systems are routinely used to analyze and improve communition, hydrometallurgical, and pyrometallurgical processes for the recovery of precious metals.

Jan 1, 1987

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By Jiqing Zhang, Jon C. Yingling, Andrzej M. Wala, Richard Ray

The purpose of this paper is to present how Computational Fluid Dynamics (CFD) simulations can be used to study the flow across the main airways of a mine ventilation system. in particular, the flow through the transition zone between the upcast shaft and main fan ductwork was investigated. These studies consider potential design modifications of this transition zone to reduce the energy cost. Although CFD has many advantages, it does not completely eliminate the need for experiments, which are still needed to validate numerical solutions. For this reason, data collected during actual mine tests and CFD simulations are compared in this pa- per. This comparison allows a better understanding of the flow phenomena. Moreover, once the numerical solutions have been validated, CFD can be used with better confidence to predict the effect of changes in ductwork configurations on energy losses. CFD reduces the number and cost of tedious experiments, while enabling a broader scope of design comparisons.

Jan 1, 1997

By Danny W. Hagood

High methane liberation and mining depth were two major factors which prompted the development of a high- capacity face ventilation system at Jim Walter Re- sources, Inc., No. 4 Mine. No. 4 Mine, one of four deep shaft mines presently under development, is located approximately 50 miles southwest of Birmingham, near Brookwood, Alabama (Figure 1). The coal seams under development are located in the Warrior Coal Field and include both the Blue Creek and Mary Lee Seams, Depth of cover averages 2000 ft. (610 m) with an average total mining height of 8 ft. C2.4 m). [ ] It is generally accepted that the methane content of a particular coal increases as the overburden depth is increased [l] ; experience to date has shown that the gas condition of the No. 4 Mine is no exception to the rule. To further compound the problem, the over- burden depth, coupled with the relatively soft nature of the Blue Creek coal, has resulted in an initial layout based upon 150 x 150 ft (45.7 x 45.7 m) centers. Considering the above-mentioned mining conditions, the means and the effectiveness of the face ventilation system becomes paramount where productivity is concerned.

Jan 1, 1980

By J. Brent Hiskey

INTRODUCTION Metal electrodeposition processes are of fundamental technological importance to a number of fields. Electrorefining, electrowinning, electroplating, and electrogalvanizing have all been the subject of intense study for over a century. More recently, electrochem- ical deposition has played a critical role in advances in microelectronics and lately has been an enabling technology for the production of certain nanostructured materials. Electrometallurgists have most frequently been concerned with the structure and morphology of massive deposits. For example, in metal recovery steps such as electrorefining and electrowinning, deposits demonstrating adherent coarse-grained characteristics are most desirable. In the case of electroplating, a bright fine-grained, tenacious and strongly adherent deposit is required. The fabrication of microelectronic devices and the production of nanoscale structures such as nanoparticles, nanowires, and nanorods requires a keen understanding of early stage deposition effects. The initial stages of metal deposition, usually referred to as electroclystallization, are fundamentally linked to nucleation and growth phenomena. Early stage deposits are typically very ordered. Whereas, bulk metal deposition structures are much more ran- dom. In both cases, the discharge of a metal ion at an electrified interface is represented by simple cathodic reduction as follows: [ ] Me(H2O)xn[ ] is a hydrated metal ion residing in the bulk solution and Me is the metal atom occupying a crystallographic lattice position. A similar reduction reaction can be

Jan 1, 2005