Search Documents

By S. Lin, Y. J. Wang

Based on systematic definitions of a generalized multiple fan ventilation system, the concepts of an augmented system, its solution curve and the operating points of the original system are introduced. The Quasi-Newton algorithm is applied in combination with the switching-parameter method to ensure a continuous search along an augmented-system solution curve and identify all the possible system operating points on it. Two example networks are analyzed to demonstrate those concepts and the application of the algorithm for identifying operating points of multiple fan ventilation systems.

Jan 1, 1994

Simulation models were developed at the Julius kruttschnitt Mineral Research Centre to provide accurate estimates of power consumption for a wide range of equipment. With the models, a range of circuits and operating conditions can be compared by simulation for a particular ore type. Accurate models of classification allow for the interaction between classifier efficiency and target product size (e.g., P80 or percent passing 150 /an) to be considered. This paper considers a range of circuit types and overall energy efficiency in the context of case studies where different circuit types were treating similar ore types.

Jan 1, 1999

By F. Kennedy

Consolidation Coal Co. (Consol) supports an active research and development effort to improve the safe, productive mining of coal and to use coal in an environmentally acceptable manner: Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1 % of Consol coal sales, which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with using the nation's abundant reserves of economical, readily available fuel.

Jan 1, 1990

By John K. Kellis

With the cost competitive nature of material mining, the ability to actively monitor the condition of the conveyor belt systems without personnel dedicated to that task is very desirable. This paper discusses the development of a conveyor belt condition monitoring system, which actively monitors the conveyor belt, without the need to install special antennas. A belt width map can be generated, as well as detection of three types of physical damages: (a) failure of mechanical fasteners, (b) reduction in belting strength due to reductions in competent belt width, and (c) longitudinal belt rips.

Jan 1, 2000

By V. A. Khartcenko

As the environment conditions deteriorate with the intensification of mining, the problems of mineral resources protection and the development and introduction of various bio- technologies are becoming more pressing This paper is devoted to the description of an ecological simulation system, related to the exploitation of a mine in a given region. We suggest mathematical tools for solving the main problem, namely an expert system, providing the simulation of ecological models for the mining complex. On the basis of the suggested models, algorithms, and software facilities, numerical modeling was carried out, as well as systematic investigation and processing of the mining activities of the complex. AS a result of this work we have obtained more effective parameters of technological and economical measures of environmental protection.

Jan 1, 1992

By A. Maréchal

It has been shown since a few years that the problem of estimating recoverable reserves should be solved by using specialized statistical techniques : whenever the selected blocks are chosen without any other constraint than a cut-off grade criterion, the problem of estimating the corresponding tonnage-grade curve is resolved by estimating the local histogram of block grades. Two major statistical techniques are currently used by geostatisticians to estimate local histograms : the "average conditional distribution" technique (Parker, Journel, Dixon 1979) and the disjunctive kriging technique. (Matheron, 1976, Jackson, Maréchal, 1979). Both have proved to be applicable in practice, with their pros and conconcerning their practibility and versatility.

Jan 1, 1982

By Donald P. Richards, David W. Campo, Michel Coudry

This paper presents a review of the grouting works of Line 2 of the Greater Cairo MetroSystem. The Nile River alluvial deposits underlying this ancient city provided for a challenging and sometimes difficult grouting project. Permeation grouting using state-of-the-art computerized grouting techniques, as well as extensive ground treatment by jet grout, was per-formed for soil consolidation and/or groundwater control. During the project, over 425,000m3 of ground was treated, requiring 1.4 million linear meters of drilling and PVC injection pipe, 54,000 m3 of bentonite cement and 230,000 m3 of chemical and mineral grout. In addition, over 70,000 m3 of ground was treated using the jet grout method. Relative to major international transportation projects, the grouting works for Line 2 of the Cairo Metro represent one of the largest worldwide grouting endeavors to date.

Jan 1, 1997

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By L. Andrews, G. Smits, M. D. Adams, E. A. Viljoen

A new approach has been developed that is capable of ascertaining the ore component that is responsible for the preg­robbing of pregnant pulps. Many gold mines are currently treating ores containing a component that is detrimental to the recovery of gold, in that they "preg-rob" the pregnant pulp by adsorption of some of the dissolved gold. The identity of the preg-robbing component in this type of ore has been the subject of considerable debate over a lengthy period, th various suggestions including amorphous carbon, chlonte, chalcopyrite and layered silicates, such as the phyllosilicate minerals pyrophyllite, kaolinite, phlogopite and illite. A means is now available to identify and characterize the preg-robber in gold ores. This new approach consists of contacting the ore with a synthetic aurocyanide solution, identifying the mineral grains by optical microscopy and analysing each grain individually using high-sensitivity electron microprobe analysis. The approach is exemplified in this initial study by identifying the preg-robbing component in an active sample of gold-bearing shale to be an amorphous carbonaceous phase consisting of discrete particles of about 5 µm diameter interspersed with shale particles and agglomerated into grains of up to 100 µm diameter. Microanalysis of these grains as well as other mineral particles revealed that the gold content of some of the carbonaceous grains was close to 7000 g,lt, with no gold being detected in any of the other mineral phases that were found to be present (e.g. quartz, chlorite, muscovite, pyrophyllite, etc). Bulk analysis of the sample for carbon and gold confirmed that gold loadings of around 7000 g,/t would be expected if all of the gold were adsorbed onto the carbonaceous component. The carbonaceous constituent is probably also responsible for the anomalously high surface area measured for the material. It probably acts in a similar fashion to activated carbon, and the correct choice of organic blinding agent will decrease the extent of preg-robbing by lowering the activity of the material for gold, without causing any downstream problems such as fouling of the activated carbon used for gold recovery

Jan 1, 1993

By John E. Frost

The Gibralter Mines Ltd. complex is 61 km (38 miles) north of Williams Lake in central British Columbia, Fig. 1. The discovery of these deposits evolved in stages such that each stage revealed a bigger piece of the elephant. When the elephant was mostly revealed, Placer Development Ltd. brought the property into production. Although Gibralter is aporphyry copper deposit, it is certainly not a typical one. Copper and minor molybdenum mineralization occur in a foliated and saussuritized quartz diorite. Ore bodies tend to be tabular in form because foliation exerts a major control on localizing mineralization. A generalized geologic map of the Gibralter-Pollyanna area is shown in Fig. 2. Mineralization was first identified in 1917 in the Pollyanna area. Several shallow pits were sunk on flashy, but low grade, lenticular quartz veins. Duval Corp. made the initial commercial discovery, the Pollyanna ore body, on what were then called the Pollyanna claims. These claims, staked by R.C. Glen and C. Gennis in 1963, were the first to be optioned by Duval in British Columbia in October 1964. Placer Development joined Duval in late 1966 as a 50% joint venture partner, and after optioning the adjoining Gibralter claims, proceeded to evaluate and develop the four ore bodies that make up the Gibralter deposit. The Gibralter claims south of the Pollyanna claims provided the name for the Gibralter deposit.

Jan 1, 1991

By Chen Bingchen, Zhang Jian, Liu Jiaxiang

The influence of various installation angles of hydrocyclone on its operation indexes was investigated, and the correspondent mathematical models were established in this paper. The models developed in this paper can be used to the optimizing control of hydrocyclone and make the hydrocyclone as a particle size sensor.

Jan 1, 1995

By James F. ` King

This paper reviews the changes which have taken place in the supply of smelter-grade alumina and refinery-grade bauxite over the past twenty years. It highlights the current situation and identifies some trends which are to be expected in the medium- and longer-term future.

Jan 1, 1986

By James R. Arnold

With all of the publicity, criticism, and notoriety that the mining industry has received over migratory birds, it is diffi­cult to remember that six years ago no one even suspected that this issue would'emerge. After all, cyanide had been used in Nevada mining for 20 years without significant effects on wildlife. Although the mining industry has been buried in unjustified criti.cism for not having a clearer crystal ball, most of those critics forget that no one else predicted this problem either. In fact, the Nevada Department of Wildlife reviewed and had no objections to the Paradise Peak Plan of Operations before they began production. As we now know, Paradise Peak had one of the first and most severe avian mortality prob­lems in the State. It should also be noted that Paradise Peak has done more to research and solve the migratory bird problem than all of the rest of the Nevada mines put together. It is not possible to review all of the research and field work that has gone into investigation of the avian mortality problem over the past five years in this short paper, but a synopsis can be presented. In most instances we can say that we have solved the problem, We have learned what works and what does not. Let's start with what does not work. Unfortunately, the list is long and elaborate, but can easily be summed up in one word: hazing.

Jan 1, 1990

The paper describes the procedure of data inquiry on the structure of mineral production in Austria and selected results. Goal of the endeavor was to gain more tangible insights into the mining industry as a basis for regulation balancing economical, ecological and social aspects.

Jan 1, 2006

By Michael W. Glasson, Archie M. Richardson, Leo Gilbride, Laine Adair

Andalex Resources, Inc. recently engaged in a ventilation planning exercise that resulted in the construction of a new main fan installation to support longwall coal mining at the Aberdeen Mine. This paper documents the planning process, including underground measurements, modeling, permitting, and construction of the new fan installation.

Jan 1, 1997

By Joe Maloney, Steve Shadow

Mining conditions at Cyprus Amax's Twentymile Coal Company (TCC) require the use of regenerative conveyors. Regenerative conveyors were first used in the Southwest Mine District and then in the challenging East Mine District. This paper will discuss the development and refinement of the equipment used to brake the regenerative conveyors.

Jan 1, 1998

By Harold L. Kike

Until recently sulphur uses were so broadly based that economists used sulphur consumption to measure industrial activity. However, sulphur use patterns are changing and the manufacture of phosphate fertilizers presently accounts for approximately 65% of the world's sulphur consumption compared with only 25% in 1960. This has encouraged the development of new agricultural and industrial uses for sulphur. Major emphasis has been placed on its use as a fertilizer and in the manufacture of paving materials, specialty concretes and coatings. Some of these uses could have a significant impact on future sulphur usage.

Jan 1, 1986

By Leonard A. Eros

In many mining applications it is not practical to use gravity takeups. In these situations hydraulic takeups are often utilized. Performance specifications are often compromised by designs which have inherently high internal friction and inefficient hydraulic designs. This results in performance which does not match the requirements of the conveyor system. A computer model has been built to check unit efficiencies and field measurements have been taken which verify the results.

Jan 1, 1993

By Wang Yingmin, Xu Zhuyun

The optimum of general mine ventilation networks is very difficult and has a considerable significance. Based on the content model, this paper presents a more general nonlinear programming model whose number of variables equals that of independent meshes. The constrained conditions are linear inequalities only. The model is changed into an unconstrained problem with multiper method. The optimum results are computed with DFP algorithm and the Improved Golden section method is used in its linear searching. The computer program written in Quick BASIC is suitable to the optimum of any type of large mine ventilation networks with different regulating devices. The paper presents two examples for optimum of ventilation networks.

Jan 1, 1991