Search Documents

By Yousef Ghorbani, Jafar Abdolahi Sharif, Fatemeh Kazemi, Ataallah Bahrami

Kinetic models are the most important tool for predicting and evaluating the performance of flotation circuits. Gilsonite is a natural fossil resource similar to an oil asphalt, high in asphaltenes. Here, in order to determine the kinetic order and flotation rate of a gilsonite sample, flotation experiments were carried out in both rougher and cleaner stages. Experiments were conducted using the combinations of oil–MIBC and gas oil–pine oil, with one test without collector and frother. Five kinetic models were applied to the data obtained from the flotation tests using MATLAB software. Statistical analysis showed that the results of the experiment with oil–MIBC were highly in compliance with all models. Kinetic constants (k) were calculated as 0.1548 (s−1 ) and 0.0450 (s−1 ) for rougher and cleaner stages, respectively. Rougher and cleaner tests without collector and frother also matched all models well (R2 > 0.98), with k values of 0.2163 (s−1 ) and 0.284 (s−1 ), respectively. The relationship between flotation rate constant, maximum combustible recovery, and particle size showed that the maximum flotation combustible recovery and flotation rate were obtained in the size range of −250 + 106 μm in the rougher and cleaner stages. The combustible recovery and flotation rate were higher in the rougher flotation process than in the cleaner stage.

By D. F. Doerr, E. Blalock, D. R. Bush, K. D. Cohen

"BACKGROUND The design, development, fabrication, and test of a cryogenic supply for a refuge alternative is part of a larger effort funded by the National Institute for Occupational Safety and Health and managed through a Space Act Agreement with the National Aeronautics and Space Administration at the Kennedy Space Center, FL to create cryogenically based life support equipment responsive to the needs of miners as required by the Miner Act of 2008. This work is done by a joint contractor/NASA team. In particular, the Cryogenic Refuge Alternative Supply System (CryoRASS) serves to provide a respirable air source to miners confined for 96 hours in a mine refuge alternative. This system stores liquid air in a zero-loss cryogenic reservoir (Dewar) until an emergency requires use. The system does not require electric power when in use by miners. Because of the very cold nature of the liquid air, considerable heat stress relief and reduction of humidity is provided in addition to the required replenishment of oxygen. Moderate dilution of CO2 also occurs.INTRODUCTION The design of this new cryogenic refuge alternative supply system (CryoRASS) uses NASA/Kennedy Space Center technology as a development baseline. The design stores cryogenic (liquid) air that is warmed in an air handler box and the resulting gaseous air is introduced to the chamber that not only causes air circulation, but relies upon environmental and human heat to expand the liquid air to a gaseous state. Therefore, the primary benefits of the liquid air source, besides atmosphere maintenance (oxygen), is refuge cooling and dehumidification. This results in reduction of human heat stress and this occurs without the need for electrical power in the refuge chamber. This reduction is a major factor in ""apparent heat"" and the human perception of comfort. Another benefit with introduction of ""air"" vs only ""oxygen"" is the dilution of carbon dioxide. The volume of new air will displace existing refuge air and this air laden with humidity/CO2/low O2 passes out of the refuge relief valves. These RVs should be strategically placed to vent stagnant air preferentially. An initial system test was conducted in our Florida facility in a production 10-person hard chamber for 96 hours. Last year (2014) the system was tested with a 23 person inflatable refuge alternative in Bruceton. For this test, the CryoRASS air handler was redesigned to offer superior characteristics when installed in a Built-in-Place refuge alternative. This report describes the results of the modified system being tested in the Pittsburgh Experimental Mine while attached to a 30 person refuge for 96 (+/-) hours."

Jan 1, 2016

By Steve Kral

Despite low commodity prices and mining industry cutbacks throughout the world, Peru remains one of the industry’s bright spots. The country’s remarkable economic turnaround during the 1990s remains a model for other developing nations to follow. And the Peruvian government has not forgotten the industry that was instrumental in that turnaround. True, the country has not been spared the effects of the mining industry’s retrenchment that has occurred in other parts of the world. However, foreign mining companies remain committed to doing business in Peru. And the government remains committed to attracting foreign investment and maintaining a strong mining industry. This commitment was evident in September 1999during the 24th Convention of the Institutos de Ingenieros de Minas del Peru in Arequipa, Peru. More than 3,000 mining industry professionals from around the world attended the convention. And Extemin, the accompanying exhibit, featured more than 450 companies, many from the United States, Canada, Australia, South Africa and other countries.

Jan 1, 2000

By M. Westendorf, T. Banerjee, S. Kaushik, D. Tinney

"The Copper Mountain Mine is located in Princeton British Columbia, Canada and produces 80 – 90 million pounds of copper annually, as well as gold and silver by-products. The ore processing plant has a conventional SAG/ball mill circuit with inline pebble crushing, followed by flotation. At most plants, much time is spent evaluating and optimizing the comminution and flotation circuits. The cyclones are a key contributor to the effective operation of the plant: They define the circulating load in the comminution circuit and provide the classification that ensures liberated material is passed through to flotation. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput in flotation. For such an impactful unit operation, cyclones have historically been under-instrumented. Consider as well that the cyclones are typically located at the highest elevation in a plant, and it becomes clear why they often underperform. Copper Mountain Mine recognized the critical role that cyclones filled in their plant and worked to optimize their operation through the implementation of a Portage Cyclone Detection (PCD) system to identify plugging and roping incidents, Portage Pumpbox Control (PPC) to manage the flow to the cyclones, and AwaRE to control the grinding circuit. As a result, cyclones overflow stability has increased, switching out a roped or plugged cyclone now happens within seconds rather than many minutes, and both the grinding and flotation circuits perform better. INTRODUCTION Cyclones are one of the most extensively used pieces of equipment within the mineral processing industry because of their simplistic operating and maintenance philosophies. The cyclones are commonly used as classifiers within the comminution circuit to control the grinding product particle size for satisfactory performance of downstream operations. The cyclones are a key contributor to the effective operation of the plant and have a significant impact on the mineral processing plant operations. If the cyclones are not performing as they should, the results are often a combination of lost recovery, grade, capacity and reduced throughput. Similarly, an inefficient cyclone operation may also lead to low or high recirculating loads that impact the efficiency of the comminution circuit. This highlights the importance to have proper stability in cyclone operation while implementing any plant-wide optimisation strategy."

Jan 1, 2015

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.

By Robert P. Larkin

The necessity for mineral extraction and its impact on man and the natural environment is a subject of increasing concern to Americans. Rising living standards and new demands for energy require increased mineral extraction, whereas the "new environmentalism" and concern over social well-being warn of the dangers to both the environment and the social system. This dilemma can only be solved by a complete understanding and analysis of all the factors relevant to human welfare which include environmental considerations, economic implications, and the social and psychological dimensions. A decision-making framework is therefore necessary which will encompass all relevant views of the problem.

Jan 1, 1975

By D. M. Ziebarth

"During the mid to late 1960’s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace supporting a large part of the world demand; until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corporation of Saskatchewan (PCS) was one of the major producers planning upgrades to their production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1500 tonne per hour hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market. This paper will describe the design challenges encountered during the development of the infrastructure around an operating facility whilst minimizing down time, schedule, capital and construction costs. This paper will also explore the strategy to increase capacity of the newly commissioned hoisting plant. BACKGROUND Potash production is a major Saskatchewan industry, and has played a significant role in the economy for over 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in twelve companies opening ten mines by 1970. In 1975 Potash Corporation of Saskatchewan was created by the government of Saskatchewan and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine (Cory), near Saskatoon. Cory has been in operation since 1968 and is located 12 km (7.5 mi) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3300 feet) below surface. PCS has embarked on sizable capital expansions of more than CDN $7 billion. The Cory CDN $1.6 billion expansion was expected to raise operational capability of the site to 2.7 million tonnes per year, an increase of 1.9 million tonnes per year (MTPY). To achieve 2.7 MTPY of finished product and considering the 22.6% average production recovery1, 12 MTPY of ore must be hoisted to surface for processing. To deliver this rate required upgrading of the hoisting plant to 1500 tonne per hour (TPH). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly the work was completed safely"

Jan 1, 2017

By Bill S. Taylor

Dutch State Mines [D.S.M] introduced the Heavy Medium Cyclone into the United States for cleaning fine coal about three decades ago. Since that time the general industry practice has been to deslime the raw coal at 28 Mesh (0. 59mm) size. The plus 28M material is fed to the Heavy Medium Cyclone for cleaning, and the 28M x 0 fraction is processed by other means (e. g. flotation or hydrocyclones). This approach recognized that 28M was the smallest size particle that could be easily rinsed on vibratory screens without excessive loss of magnetite, and without blinding of sieve bend and vibratory screen decks. Another reason for the 28M de-sliming was to avoid excessive contamination of the media with non-magnetic coal, shale, or clay fines. The most undesirable of these contaminants is the sub-micron size clay particles (2) that greatly increase the viscosity of the media and reduce the numerical maximum level that the media specific gravity can obtain due to the lower specific gravity of clay with respect to magnetite. The higher the fugitive clay content, the more severe the preceding problems become. During the last 30 years, many conventional Heavy Medium Cyclone Plants have been built throughout the world. In the United States, the initial cyclone plants were confined to the production of high quality metallurgical coal where lower gravities of separation were required than could be obtained from the conventional hydraulic or air separation processes. In recent years a large and ever-increasing number of preparation plants producing steam coal have started utilizing Heavy Medium Cyclone technology due to the environmental pressures being encountered to produce low sulphur coal. Due to the inherent characteristic of many coals of having a lower pyritic sulphur content at lower specific gravity fractions, many applications and markets are appearing for separating steam coals at much lower specific gravities than have been historically normal in the United States. Therefore. Heavy Medium Cyclones are being utilized to a much greater degree in this field, due to the flexibility of low separating gravity ability coupled with high efficiency when high percentage of near gravity material is present.

Jan 1, 1978

By Leonard B. Rothfeld

For many years, pulverized coal (PC) boilers in utility power plants have been the dominant market for domestic coal. Today, two new coal utilization technologies challenge the PC boiler's dominance. Atmospheric fluidized bed combustion (AFBC) and "coal gasification/combined cycle" (GCC) stand on the verge of commercial demonstration in the utility environment at a scale of 100 MW. Developed over the past decade, these technologies respond to the demands for cleaner ways to burn coal and for more flexibility in fuel supply. In the near term, these are the "clean coal" technologies most likely to have a significant impact, because they are ready for commercial application. As for environmental acceptability, consider that just a few years ago one of the environmental slogans was "no coal in California." Indeed, the only large quantities of coal above ground in California at that time were in transit on the way to Asia. Today, thanks to new technology, we can point to two operational coal-burning plants in California and one in the works: * Cool Water GCC demonstration plant (100 MW) * California Portland Cement AFBC commercial cogeneration, near Riverside (190 000 lb/hr steam) * Energy Factors AFBC commercial cogeneration at Stockton, to be operational 1988 (44 MW)

Jan 1, 1987

By R. V. Ramani, K. V. Raj

"The air flow problems in open pit mines are complex. Computational fluid dynamics (CFD) models provide a detailed knowledge of the airflow pattern and velocity distribution, temperature, and pollutant concentration within an enclosed domain of the open pit. A range of turbulent model can be selected for varying complexity and accuracy. Pollutant transport models, however, differ in their assumptions and structure as well as in the algorithm they use; as a result, prediction varies from model to model. This paper presents a study of pollutant transport in an actual open pit mine under stable boundary layer. The objective is mainly to test two turbulence models using the same input conditions, model constants, and similar geometry. Measured data are used to compare results of the two CFD models, namely, the kappa-epsilon (?-e) model and the Large Eddy Simulation (LES) model. Despite the complex synoptic situations, different meteorological input data and the fast changing conditions, the simulation results from both the models are in good agreement regarding the dispersion of pollutants.INTRODUCTION Modeling of contaminant transport under Arctic air inversion is an important step for an assessment of the amount of pollutants within the open pit. The Airflow in open pit mines is of larger scale and does not follow the principles of pipe flow. The air flow problems in actual open pit mines are thus far more complex. CFD models provide a detailed knowledge of the airflow pattern and air velocity distribution, temperature, and pollutant concentration within an enclosed domain of an open pit. There is no known application of CFD in three-dimensional modeling of air flow in large open pit mines. Two equation RANS kappa-epsilon (?-e) and Large Eddy Simulation (CFD) models, however, have been developed to solve the stable boundary layer (SBL) problems in Atmospheric Sciences (Baklanov 2000, Basu and Porté-Agel 2006, Dop and Axelsen 2007, Bandopadhyay et al. 2014). Because an exact flow situation in open pit mines is not known a-priori, it is therefore, necessary to investigate various turbulent models to identify the appropriate model that would simulate the flow phenomena with reasonable accuracy, and predict the contaminant distributions within the pit. Dispersion models differ in their assumptions and structures as well as in the algorithm they use and, as a result, predictions vary from model to model. Furthermore, it is also important to investigate the behavior of a CFD model in simulating a complex phenomenon such as the transport and distribution of contaminants in open pit mine under Arctic air inversion. The simulation of an enhanced period of turbulence in SBL is of particular interest because traditional air pollution dispersion models cannot explicitly treat such intermittent events, and yet the SBL is often the worst-case scenario in an open pit pollution transport"

Jan 1, 2015

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By S. K. Ghosh

This paper discusses how the information on ash composition, ash-fusion temperatures, and ash-slag viscosity can be utilized to predict slagging and fouling potentials of a particular coal. A review of several empirical parameters which are commonly in use for determining such potentials is given. Also, some guideline values for interpreting the relative propensity of slagging and fouling of various types of coal are provided.

Jan 1, 1983

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By Todd Schrauf, James Scott, Mark Smith

"Cyanide heap leaching of gold ores in areas with extremely low winter temperatures requires special considerations to prevent freezing of the leach solution. Factors that impact the solution temperature include ore temperature at the time of stacking and during operation, burial of drip irrigation lines, use of geomembrane covers and heating of the leach solution. Thermodynamic modeling was performed to simulate expected ore and solution temperatures under different operating strategies for Kaminak Gold’s Coffee gold project in the Yukon Territory. Mean monthly temperatures at the site ranged from a low of -22.5 °C (-8.5 °F) to a high of 13.6 °C (56.4 °F), while in situ ore temperatures ranged from -0.5° to about -1.5 °C (31 ° to 29 °F). The modeling results were used to optimize the operational parameters and indicated that a combination of drip line burial and heating of the leach solution during the winter months was required to maintain solution temperatures above freezing during the initial years of stacking, although as the size of the heap increased, heating was no longer necessary.Modeling objectivesThe successful operation of a cyanide heap leach under extremely cold winter temperatures requires the implementation of operational strategies to prevent freezing of the leach solution and the ore within the heap. Thermodynamic modeling of the heap provides the means to quantify the effectiveness of these different operational parameters on maintaining the required operating temperatures to avoid freezing within the heap. The operational parameters that were evaluated with the model included:"

Apr 1, 2016

By Dan Ifrim, Andre Solecki

Tunneling could be a major challenge to tunneling contractors as tunneling operations can be seriously affected by the Tunnel Boring Machine (TBM) performance. Specifying the appropriate TBM methodology, selection of systems and features, is critical for managing tunnel risks and contribute to successful tunneling project. The paper analyzes tunneling records from the recently completed City of Toronto’s Ashbridges Bay Treatment Outfall tunnel project and underlines the righteous selection of the TBM type and associated TBM systems in achieving good advance rates during tunnelling and managing project risks. The paper intends to draw attention of a few aspects of TBM technical specification importance and highlight the lessons learned from this process.

Jun 13, 2023

By H. Dreissen

Upgrading of low-concentration ores is of growing importance today. The Heavy Medium Cyclone Process, thanks to strong centrifugal forces, effectively separates particles varying only slightly in specific gravity but widely in size. The paper discusses the separation efficiency, the method of assessing that efficiency, and the influence of such factors as medium solids. The operating results of nine heavy medium cyclone plants handling following minerals are reported: barite, wolfram, iron, magnesite, diamond, lead-zinc, fluorspar, rocksalt potash. Highlighted are an improved recovery system for heavy medium and some other developments, such as techniques for separation down to 0.1mm and the application in the field of recycling.

Jan 1, 1980

By P. Guliov

In the first part of this paper the authors present an overview of industrial minerals produced in the Canadian provinces of British Columbia, Alberta and Saskatchewan, and supplied to the Pacific Rim countries. The second part outlines some of the unique opportunities for industrial minerals that exist in the three western Canadian provinces and those minerals we feel have development potential for overseas markets. Because of time constraints, it is not an exhaustive presentation on industrial minerals, but is focused on a few selected minerals that we believe have high potential.

Jan 1, 1990

By Derek J. Barratt

The existence of a critical size buildup in an autogenous or SAG mill can be predicted from proper examination of drill core and ore samples. Methods of dealing with such critical size in a primary mill are reviewed in the context of ore properties, whether or not pilot plant-scale testwork has been conducted, and also with respect to the design of new plants or the retrofitting of existing operations. The implications of not planning for pebble crushing in situations where it is appropriate are discussed.

Jan 1, 1992

By Hongqiang Wang, Qingliang Wang, Eming Hu, Zhiwu Lei, Fang Hu, Rui Zhang, Wei Hou

Pyrite, a mineral associated with uranium ore, is closely related to uranium leaching. In this study, Ozone micro-nano bubbles (OMNBs), as an environmentally friendly advanced oxidation technology, were used for the first time to oxidize pyrite under experimental conditions to improve the leaching rate of uranium. A laboratory-scale agitation leaching experiment of pyrite was carried out with a pH of 1.0–3.0, gas flow of 1–3 L/min, ozone generation rate of 0.55–2.22 mg/s, and pyrite concentration of 0.1–5.0 g/L for 1 h. By adding three different co-oxidant: Mn(II), Mn(IV), and Fe(III), it was found that only Mn(IV) increased the oxidation rate of pyrite by 21.7%. The results of the scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the formation of Fe(III)-O film on the surface of the ore suppresses the oxidation rate of pyrite to a certain extent. Pyrite can be rapidly oxidized up to 57.6% by OMNBs, which is beneficial to uranium leaching. This method is expected to be used for in situ acid leaching of uranium with OMNBs injected into the ground.

Jan 3, 2022

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016