Search Documents

By J. Dorsey

In 1910, Colonel Boyce Thompson, who owned Inspiration (now Cyprus Miami) and various other mining interests, formed the Magma Copper Company and leased the Silver Queen claims around Superior, Arizona. At the same time, he purchased other claims around the Silver Queen claims from what was then called the Magma Mine. The mine continued to operate until 1982 when Newmont Mining Company, who owned Magma Copper Company, shut down the operations due to high costs and low copper prices. When Magma was spun off by Newmont as an independent company in 1987, new studies of Superior were started. It was clear from these studies that the mine had been shutdown and over 1400 employees laid off for two basic reasons: first, as a resu1t of a mine plan that was technically flawed and second, be-cause of very high production costs mainly due to the low productivity from a very high cost work force. During 1989 a plan was formulated to re-open Superior with the determination to over-come the problems that resulted in closure. A new mine plan was developed and a management style developed that promotes team work and high productivity.

Jan 1, 1992

By L. Martin, M. Raffaldi, M. Stepan, D. Benton

The Office of Mine Safety and Health Research, Spokane Mining Research Division, is continuing its high-energy, high-displacement testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link mesh, welded-wire mesh and combinations of them. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can assist in interpreting the condition of installed surface support. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to better quantify the stability of installed shotcrete support.

Jan 1, 2016

By R. Kent Comann

Introduction This article describes ways to maximize employment potential for those looking for a job in the minerals industry. Advice on the right way to prepare a resume is followed by tips on where and how to look for a job and ways to make the best of an interview. Information on current salaries is also included. RESUME NAME: Give home and college addresses and telephone numbers, ADDRESS: if still in school. Otherwise, give home address and TELEPHONE: telephone plus business telephone number. JOB OBJECTIVE: What do you want to do? EDUCATION: List degree(s), name of college(s), location(s), and date(s) degree(s) received or to be awarded. Do not list your high school but do include postgraduate education, training, or seminars. WORK EXPERIENCE: List your most recent experience first, and the rest in reverse chronological order. Include dates (month and year) and company names. First show the entire time spent with each employer, then list the various jobs (with dates and duties) you may have had with this employer. MILITARY SERVICE: List dates, branch of service, and duties. If you did not serve, delete this section. COLLEGE ACTIVITIES: Show organizations, sports, and offices held. Only list these if you are a graduating senior, otherwise delete this section. PERSONAL DATA: List age, marital status, height, weight (optional), foreign languages spoken, professional memberships, and health (if good or excellent, otherwise do not mention it in the resume). If you prefer a certain location and would not accept a job anywhere else, list the location desired. Otherwise, do not restrict yourself. Also list special skills, hobbies, or interests that will help sell you to the company. Be brief in this section and use good judgement as to what you say. REFERENCES: Furnished on request. Resume Guidelines There are some things to remember when preparing a resume. These include: • Limit your resume to one page, unless you have a lot of experience. Then it should be a maximum of two pages. • Use 8.5 x 11 plain bond paper, white or off-white. Stay away from colored paper, odd size paper, and cute resumes. They are counter-productive. • Make certain your resume is typed professionally. Be sure to check for spelling, grammar, and typographical errors. • Have your resume reproduced by copier or printing shop. Do not use carbon copies. • Keep your sentences and remarks short and punchy. Use action verbs. • Have a good layout that is easy to read, brief, and uncluttered. Allow some white space in your resume. There are also some things you should not do when preparing a resume. These include the following: • Do not include a photograph or mention your religion, race, or sex. • Do not leave gaps of time unaccounted for in your resume. • Do not include your college transcripts with your resume or list all the courses you took in college. • Do not list all the articles you have written. Only list one or two, if appropriate for, say, a research and development job. • Do not include reference letters with your resume. Any good, prospective employer will make telephone reference checks. • Do not use "Curriculum Vitae," use "Resume." • Do not include unnecessary data such as your social security number, passport number, or PE registration number. If you are a PE or EIT, be sure to mention that in your resume. Do not mention US citizenship or US work permit unless you have a foreign education or are not a native US citizen. • Do not include present salary or salary requirements. This will come out in the interview. • Do not use the word "I" in your resume or refer to yourself in the third person. • Do not lie, distort, exaggerate, or editorialize in your resume. • Do not have your resume prepared by an outside resume service. This is unnecessary, costly, and generally not effective.

Jan 2, 1985

By John Newby, Edward Kennedy, Ulf Gwildis

Alluvial deposits of major rivers often provide relatively uniform tunneling conditions. However, these conditions pose specific challenges due to the tunneling behavior of the granular soils as flowing ground, if unsupported. This paper describes the design considerations and construction experiences gained during the Tunnel Boring Machine (TBM) drives for the Annacis Island WWTP New Outfall System in the Vancouver, B.C. metropolitan area. Meeting the design criteria for connecting two (2) deep on-land shafts with an in-river riser manifold required advancing a 5-meter-diameter slurry TBM through the Fraser Rivers sands and at a tunnel invert elevation with a baseline hydrostatic head of 3.4 bar.

Dec 1, 2022

By C. M. Bartley

Canada has been a producer of sulphur in various forms for about 100 years, Pyrites, as a source of sulphur dioxide for the manufacture of sulphuric acid, were being mined in the 1860's. Smelter gas, for the same purpose, has been recovered since 1928. Between 1935 and 1943, and from 1952 to the present, elemental sulphur has been produced in Canada from two raw material sources and by several methods. This paper attempts to present a view of the current status of the elemental sulphur industry in Canada based on the sour gas fields of Alberta and British Columbia. Production from this source has increased rapidly in the past 12 years to make Canada one of the major sulphur producers of the world. The present industry in Canada relies mainly on sour gas sulphur and it is expected that it will continue to grow in the future. However, before describing current activity relating to sour gas it may be of interest to outline briefly the early pyrite activities, the roots of the sulphur industry in Canada.

Jan 1, 1964

By George R. Powe

If Campbell County, Wyoming were an independent nation, it would rank fifth in the world among countries with known coal reserves. Only the United States, Russia, mainland China and West Germany would have greater volumes available. Not too many years ago that statement would not have seemed important, because oil and natural gas had become our nation's principal fuels. Western coal deposits, particularly those of the Powder River Basin in Montana and Wyoming, and which underlie virtually all of Campbell County, were largely unknown. But recently, in response to the three-pronged stimulus of vanishing gas reserves, rising petroleum prices, and clean environment statutes, these vast deposits have been delineated and have become, in the minds of many, indispensable to our goal of energy independence. Not only does western coal lie in thick seams near the surface where it can be mined in huge quantities at low cost, but also it possesses another coveted attribute in this age of environmentalism: low sulfur content. At Burlington Northern we count ourselves at the forefront of those who believe this coal is essential to any hope for the government's "Project Independence." But to that belief we add another article of faith. We are convinced the economics of unit train delivery of this incredibly immense resource make it the only transportation system that can help us achieve energy self-sufficiency in this country.

Jan 1, 1975

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul road conditions can positively impact mine operations resulting in increased safety, productivity gains, increased tire life, and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain mine, monthly site severity studies, ad hoc inspections by frontline supervisors, or operator feedback reporting is used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage, and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

Sep 15, 2020

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By Luke Clarkson, David Williams

The intent of this paper is to provide overview context to allow broader understanding of conventional tailings dam failure mechanisms. The research leverages global knowledge, experience, and data collection and interpretation for the safe and controlled management of the geotechnical stability of a tailings storage facility. The motivation for this review is to facilitate transparent access to tailings dam background and understanding. This paper addresses the core understanding of geotechnical failure mechanisms, and how these eventuate to instability and failure of tailings dam structures. This research focuses on foundation failure, internal erosion and piping, overtopping, seepage, seismicity, and slope instability and provides insight into what factors contribute to failure, how failure progresses due to such failure, anticipating and monitoring for the aforementioned failure modes, and designing to mitigate their risk.

Feb 15, 2021

By William C. York-Feirn, Jeffrey H. Kravitz, David Stalfort

"Mining is an inherently risky business. Over the years, major mine disasters have resulted in the deaths and injuries of thousands of miners in the United States. These disasters also resulted in innovations in approaches to mine design, operations and the training of miners and mine rescue teams. The U.S. Congress responded to these disasters with new laws designed to create mandatory safety and health standards as a means to eliminate fatal accidents; to reduce the frequency and severity of nonfatal accidents; to minimize health hazards and to promote improved safety and health conditions in the nation’s mines.Following a mine emergency preparedness and response holistic gap analysis in 2012, the U.S. Mine Safety and Health Administration (MSHA) identified the need for the development of risk and readiness assessment models for MSHA and the mining industry. MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the mining industry for use at operational levels. In 2012, MSHA hired ABS Group, a recognized industry leader in safety risk management and a wholly owned subsidiary of the American Bureau of Shipping, to develop self-assessment models to help meet this objective.In September 2012, MSHA chartered a project to supply the coal mining industry with a pro-active toolset for mine operators to:1. Self-assess the risks associated with underground coal mining operations in order to prevent major mine emergencies.2. Assess the preparedness of mine operators to respond to an emergency.3. Measure the readiness of mine rescue teams and responsible persons to execute emergency plans.MSHA’s objective was to evolve existing theoretical concepts for risk and readiness assessment into simplified tools that can be applied by the coal mining industry for use at operational levels."

Jan 10, 2018

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

The 86th Annual Meeting of the SME Minnesota section/74th Annual University of Minnesota Mining Symposium partnered with the Canadian Institute of Mining Metallurgy and Petroleum (CIM)?s Iron Ore Symposium for a historic joint conference, held this year in Duluth, MN, April 15- 17. One of a flurry of recent collaborations between SME and CIM, the joint conference was a natural fit for the conference held in the heart of the Iron Range. As CIM National President Terence Bowles said in his joint keynote with SME President Jessica Kogel, ?The U.S. imports $51 billion from Canada and Canada imports $38 billion the U.S.; that?s 50 percent of Canada?s exports and 51 percent of its imports.? The two countries? economies are linked, and nowhere more closely than in their iron ore mining activities. Kogel opened the conference with a plenary speech identifying the top 10 issues facing mining and how these issues present opportunities for mining companies. She said that it is important that the mining industry stay flexible and adapt to changing conditions, or it will go the way of the dinosaur. However, she said that these challenges can lead to new opportunities. For example, one of the major challenges facing mining is the current state of risk aversion among investors, which makes for ?less money in the pipeline.? However, this situation creates a better climate for mergers and acquisitions, which is another, less risky way to get funding. Likewise, another challenge globally is geopolitical risk; this challenge is likely to drive growth toward stable countries, which was good news for an audience composed mostly of Minnesota and Canadian mining industry personnel. One of the highlights of Kogel?s address was a triangle illustrating the interdependent nature of sustainable development and corporate social responsibility (Fig. 1). This triangle consists of four equal components: the social environment, transparency, local and global impact and future generations. The most important takeaway, Kogel said, was that sustainable development and environmental and social responsibility, while they do add to the cost of doing business, are no longer optional.

Aug 1, 2013

By L. Yuan, J. H. Rowland III

"In 1995 and 2003, the Mine Safety Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) being used in underground coal mines in the United States. The survey reports showed data for the different AMS manufacturers, the different types of equipment monitored, and the different type of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along the belt haulage entries. As of December 31, 2009, point-type heat sensors were prohibited for use for an early fire detection system; instead carbon monoxide (CO) sensors are now required. This report will examine the number of AMS currently used in underground mines in the United States to see if there is a change in their use. The locations and parameters monitored by AMS are also discussed. INTRODUCTION The last survey conducted by the Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems (AMS) used in underground coal mines in the United States (US) was in 2003 [1]. The survey report states that since 1995 there had been a steady increase in the use of AMS in underground coal mines as the technology of CO sensors was improved by manufacturers. AMS had become more reliable and some CO sensors could be purchased with the capability to discriminate between the CO produced from a fire versus CO produced from diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed for the miners to take the necessary action to put out the fire or exit the mine. It should also be noted that at the time of last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than using point-type heat sensors [2]. Finally, since the last MSHA survey, regulations have changed on the type of automatic fire detection systems permitted to be used in conveyor belt entries. As of December 31, 2009, point-type heat sensors are not permitted to be used for fire detection in underground coal mines in the US; instead CO sensors are required as a replacement (30 CFR 75.1103-4). This study will examine how the changing of the above regulations has impacted the use of CO sensors in underground coal mines in the US compared to their use based on the last MSHA survey. Importantly, in the previous MSHA survey, the data was recorded for producing and non-producing coal mines. In this study, only the data from the producing coal mines was recorded. Data was collected from a total of 235 coal mines for this study with the help of the MSHA district offices."

Jan 1, 2017

This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified.

Jan 1, 1986

By S. N. Gurulaxmi, Veerendra Singh

The abstract discusses the increasing consumption of manganese ores and the need to utilize low-grade ores and rejects. The study focuses on developing a low-cost process using a cupola furnace to recover manganese values from these resources. The process involves smelting ore blends to produce high MnO slag and pig iron. The study investigates various factors to improve iron reduction and separation from MnO-bearing slag. The results show that the process can produce slag with MnO > 35% and Fe(t) < 5% using low-grade Mn ores. The process also achieves Fe reduction between 50 and 70%. The cupola furnace offers advantages like low cost and ease of operation, making it suitable for processing low-grade ores and rejects to produce synthetic MnO-enriched products for various industries.

Apr 1, 2022

By H. M. Breza

Recovery of phosphate concentrate has received increased attention as the existing mine and plant production capacity limitations of the Texasgulf Inc. Aurora, North Carolina Mine are reached. Improved mining techniques and mineral processing of waste streams offer a potential to increase overall phosphate production without major expansion of the Mining facility. Innovative processes have been or are being identified to maximize pit mining recovery and to minimize losses in waste streams, resulting in more effective use of the valuable phosphate natural resource. This paper will describe the various continuous recovery improvement programs being implemented to achieve this goal.

Jan 1, 1994

By William P. Blacutt

This paper describes the strategy, the struggles, and the obstacles encountered during the last two years in the ongoing process to capitalize Vinto. The effort involves the offering of a vertically integrated business package composed of the tin and antimony smelters along with the two principal tin mines of the country. Capitalization: Bolivia&apos;s Innovative Approach for Privatization, the Vinto Case provides a summary of hard-earned lessons. These experiences can be success- fully implemented in other nations committed to transforming their state natural resource sector.

Jan 1, 1998