Search Documents

By F. B. Henderson III

Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016

By Ted DePooter, Mun Wei Leong, Chad Frederick

Downtown Bellevue Tunnel (DBT) is part of Sound Transit’s $3.7 billion, 14-mile light rail transit system from downtown Seattle, across Lake Washington, to the cities of Mercer Island, Bellevue, and Redmond. The tunnel was the first Sound Transit East Link project and posed significant construction risk. This paper discusses implementation of design changes to the soft ground tunneling method, implementation of several technologies such as the use macro-synthetic fiber initial shotcrete lining, use of spray-applied waterproofing, and use of shotcrete for the final tunnel lining. These efforts allowed for significant time and cost savings to the project.

Jun 13, 2021

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By Xiaozhen Song, Ashish Ranjan Kumar, Shimin Liu

To investigate the influence of boreholes, fans, and curtains for large opening underground mines (LOUM), we conducted a field survey for LOUM with the survey data serving as the numerical modeling inputs using computational fluid dynamics (CFD) models. Five different CFD modeling results were obtained with different borehole, box fan, and curtain setting conditions. The results indicate that most air quantity directly escapes through outlet 1 after coming into the inlet, causing a huge loss of airflow; volumetric air exchange index (VAEI) and minimum hours of fully exchanging the air (MHFEA) measure air exchange efficiency, with zone 2 of case 5 having the highest VAEI; The borehole minimally affects zones 2, 3, and 4, but drastically alters airflow direction in zone 1; The box fan enhances airflow to zone 2, improving ventilation efficiency and increasing VAEI; Curtains have little effect on distant working faces but influence airflow near inlets and outlets. This study provides a foundation for future research on the influence of boreholes, fans, and curtains, as well as optimizing their placement and effectiveness in face ventilation.

Feb 22, 2026

By Robert T. DeGavre

I have been asked by the Society of Mining Engineers to present a paper on Inco Limited's Indonesian nickel project as a case study in the financing of large overseas mining projects. I welcome this opportunity It is a story worth telling not only because the project itself represents a significant human achievement but also because there are certain important lessons that can be derived from our experience in financing the project. The paper will be divided into four sections: (i) a brief history of the project, (ii) a critical appraisal of the project's financing plan in terms of the goals that we sought to achieve, (iii) some comments on certain factors underlying the relative success of the financing plan, and (iv) the contributions that the engineering staffs must make to a successful financing plan. The paper will not present a technical assessment of the project since Inco Limited has been asked to submit a series of papers on this subject at the International Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979.

Jan 1, 1978

By R. L. Grayson

In 1995, Congress abolished the Bureau of Mines in the Department of Interior but preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the merger of the former Bureau with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data informed" priority setting. This presentation will review current surveillance information concerning the level of injury and disease from mining work and will discuss how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 1998

By Samuel Rigert, Marco Bettelini

"INTRODUCTION AND OBJECTIVES Long rail tunnels require in most cases powerful mechanical ventilations. Besides requirements related to normal operation and maintenance, operational safety always requires a high level of smoke management. Identifying the optimum ventilation concept is essential for achieving proper performance and safety while keeping investment and operational cost at a reasonable level. For the purpose of the present paper, long tunnels have a length of typically 20 km or more. This is related to the European classification of trains (TSI 1303/2014), where the maximum distance from the portals to a firefighting point and between firefighting points is limited to 20 km (only category B passenger rolling stock allowed) or 5 km (general case). From TSI 1303/2014 it can be concluded, that tunnels over 20 km require in any case emergency stations with complex mechanical ventilations. Based on the experience arising from a number of recent projects in the European area, including in particular Gotthard (GBT), Lötschberg, Lyon-Tourin (LTF), Brenner (BBT) and Gibraltar, safety-relevant issues related to the ventilation of long railways tunnels are reviewed in this paper. Amberg Engineering is directly involved in these challenging design tasks and can provide first-hand experience and know-how. As a particular highlight, special attention is devoted to the longest tunnel worldwide, the 57 km long Gotthard Base Tunnel, which will be commissioned in 2016. THE GOTTHARD BASE TUNNEL Overview The Gotthard Base Tunnel will be commissioned in 2016 (official inauguration on the 1st of June and beginning of regular operation on the 11th of December) and will be the worldwide longest tunnel. Its complex and powerful ventilation system is very representative for many other long tunnels and is used as reference in this paper. Therefore, a few key characteristics of the Gotthard Base Tunnel and its ventilation system will be described in some detail in this initial chapter. The Gotthard Base Tunnel (GBT) consists of two single-track tunnel tubes with connecting galleries every 312 meters. Two so-called multi-functional stations (MFS), located at roughly 1/3 and 2/3 of the tunnel length, host the key equipment for normal and for emergency operation. At these locations, double crossovers allow trains to switch from one tunnel tube to the other. An emergency station is located in each multifunctional station, allowing trains to stop in case of emergency. The general layout of the GBT is presented in Figure 1."

Jan 1, 2016

By R. L. Grayson

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate « 20 employees) was approximately ten times higher than the national coal industry rate. Although the total number of fatalities decreased to 17 in 1992 (from 22 in 1991), West Virginia still led ,the nation in coal mining fatals. A team of mining and safety professionals from West Virginia University studied the problem over the past year, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training. A clear path for 'formal intervention was determined and is presented here.

Jan 1, 1994

By D. J. Sweet, B. Seymour, T. M. Emery, M. Armatys, J. P. Bourgeois, W. Johnson

The Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) has partnered with a narrow vein, hard rock underground mine to research the effects of the binder content on the elasticity and post-peak ductility of cemented hydraulic backfill (CHB). This is part of a larger study to enhance the long-term integrity of ground support in underground mines. As mining advances deeper and stresses increase, CHB mix designs will benefit if they can be modified to handle higher levels of strain which are induced by an increased stope closure, typically affected by a reduction in stope width and increased mining depth, or through dynamic loading resulting from a local seismic event. This portion of the research examined the impact of reductions in binder and their impact on Young’s modulus, peak strength, and post-peak ductility.

Mar 2, 2022

By Larry S. Diaz

The paper considers the selection of control instrumentation for a modern flotation plant, as well as the best interpretation and most effective use of the process data obtained. Process control computer availability is considered from the outset. A general philosophy of control is proposed which leads toward a system that is its own reliability monitor. The bulk of the problems are in grinding and classification. Alternative control methods are described that use particle size measuring devices. Flotation controls, based to a large extent upon on-stream X-ray analysis, are reviewed in detail. Reagent control methods are also examined. Methods to analyze the data obtained from the various measurement devices are introduced. These methods would enable an estimate of the validity of the data and require some redundant information. Another objective of these methods is the protection of operating equipment from possible control malfunctions. Although the discussion generally considers some degree of computer usage, this paper attempts to describe instrumentation and data analysis methods that enable control with or without the process control computer.

Jan 1, 1972

By Weiguo Xie, MARK LAPUTKA

The pyrometallurgical industry plays a vital role in producing metals for our modern life. With growing demand of metals and declining grade of mineable ore, innovations become critical for many mining companies. It is necessary to conduct a review of recent improvements to the pyrometallurgical industry on analytical measurement techniques, process and equipment improvements, and computer-based modeling/simulations. Many of those innovations tend to be applied to wider metals, and not be restricted by a specific metal. Therefore, we tried to cover the wide applications of many improvements to wider range of metals to reflect this trend. The challenge of a lack of robust measurement techniques under high-temperature conditions within a furnace hinders optimization of a pyrometallurgical process. Some future opportunities in the pyrometallurgical industry on analytical measurement techniques, computer modeling, and processes and equipment have also been outlined and discussed.

Jan 26, 2021

By Bradley V. Nelson

A number of improvements in the ventilation system at the Henderson Mine have been made during the past several years. A key to these improvements was the installation of a computerized monitoring and control system. Employees can determine the status of any of hundreds of devices in seconds through the use of this monitoring system. Mine dewatering pumps, the water treatment system, the ore haulage system, electric power usage as well as other devices are controlled and/or monitored. Ventilation parameters which are monitored include air flow volumes and carbon monoxide as well as the status of main surface fans, mine doors, and ventilation raise doors. Main underground fans are also constantly monitored and can be controlled remotely. These underground fans can be programmed to automatically start and stop to follow work schedules, optimizing air quality while reducing power cost. Mine air heating costs have been reduced by replacing an electrical resistance heating system with a direct fired natural gas heating system at the portal of the ore haulage tunnel.

Jan 1, 1995

By Steve Kral

The concept of sustainable development is not new to the mining industry. Many people involved with mining have argued that the industry throughout the world has always supported the communities where they operated. They say that the mining industry was employing sustainable development practices before the phrase became fashionable. The mines employed residents and supported the local economy through tax payments and the purchase of goods and services from local businesses. In many cases, mining companies have built medical facilities and contributed money, equipment and services to local schools. In modern times, mining companies have donated reclaimed land to the local communities for use as parks and recreational facilities.

Jan 1, 2004

By J. Kretschmann, N. M. Smith, J. F. Brune, P. Goerke-Mallet

Coal production and coal use for electric power generation are diminishing worldwide. Germany will phase out lignite mining as well as lignite and hard coal-powered electricity generation by 2038. In the United States, coal production has dropped by more than 50% since 2006, including in key coal production states like West Virginia and Wyoming (EIA 2021). Closing mines and power plants across entire mining regions has significant socio-economic impacts. Existing industries must be focused on the post-mining economy by attracting new industries, and implementing job retraining programs for displaced workers, as former mining regions transition towards agricultural, industrial and recreational use. This paper examines the German “exit from coal” under the 17 UN Sustainability Goals and illustrates the complex procedures, interrelationships, risks, and rewards of the transition towards renewable energy sources, including wind, solar, hydrogen, and bioresources.

Mar 2, 2022

By Anastasia Xenaki, Edmundo Laporte, Antonio Nieto, Jesus Castillo Gomez, Oscar Velasquez

It is particularly challenging for the mining industry to create and implement an efficient and adaptable mining innovation model to secure the continuous improvement of processes and products via technology. Human resource departments must play a vital role in shifting the mining culture, enabling these new classes of digitally skilled professionals to manage the mining operations of the future. This paper proposes the implementation of a concept based on the 5S mining innovation model ((a) Nieto, 2019), in a coal mining project in Central Asia, Mongolia. Practical and empirical evidence suggests that the model could serve as a roadmap to developing technologies and methods for the mines of the future.

Feb 1, 2023

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By Daniel G. Ganey

Kerr-McGee Coal Corporation has used diesel face haulage and support equipment at its dual-seam Galatia Mine in Southern Illinois since production activities commenced in 1983. The mine began production from its lower seam, the Harrisburg No. 5 coal seam, in October 1983 and from the upper Herrin No.6 coal seam in April 1985. Before production began, the company developed a program designed to make use of the flexibility offered by diesel equipment. While productivity was an important goal, the top priority of the program was to provide a safe and healthy work environment for the miners. Management believed that high productivity would naturally follow. History has proven this belief to be true.

Jan 1, 1990

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By Fiona Woody

Lime and calcium products are essential building blocks to the modern world, used to purify drinking water, preserve foods, control pollution, improve crop yields, stabilize soil, pave roads and support the production of steel, cement, glass and many other industrial processes. While lime is essential to society, it also has a sizable carbon footprint. Approximately 30 percent of the scope 1 greenhouse-gas emissions generated during lime production are related to fuel combustion, while the remaining 70 percent are created by the unavoidable chemical reactions during calcination.

Feb 1, 2026