Search Documents

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom-designed radial sector sampler , six large blasthole samples were collected to perform the test developed by Pierre Gy to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to total fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32 percent and ±49 percent for copper and molybdenum, respectively. A classical statistical analysis conducted on the data confirmed the level of RSD native to the mine. About 95 percent of the sampling error was produced from one step in the sampling protocol, that of reducing the 1-kg (2.2-lb) sample to a 50-g (0.1-lb) sample for chemical analysis. To minimize the FSE, the use of a slightly different protocol is recommended. The 1-kg sample (2.2-lb) should first be crushed to a 0.2 cm (0.08 in.) particle size. A 250-g (0.5-lb) split should then be taken and finely ground, from which a 50-g (0.1-lb) split should then be taken. These simple steps will reduce the FSE to ±7.9 percent and ±17 percent for copper and molybdenum, respectively. The modified sampling protocol effectively reduces to zero the probability of misclassification of low-grade ore. IntroductionThe Erdenet copper-molybdenumopenpit mine is located in Erdenet in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is 1.5 to 3 km (0.9 to 1.8 miles) wide and about 25 km (16 miles) long (Erdenet Mining Corp., 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 Mt/a (29 million stpy) of ore."

Jan 11, 2017

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

By E. Asselin

Passivation of Fe-Ni-Co alloys during the Caron leach process is thought to result in low cobalt recoveries in ammoniacal ammonium carbonate solutions. A brief review of the available thermochemical data for the (Fe, Ni, Co)-NH3-H2O systems has been undertaken. The stability of the Co(II) and Co(III), Ni(II) and Fe(II) ammines was examined through the use of speciation and Pourbaix diagrams at 298 and 333 K and at 6 M total ammonia. Increasing the temperature reduces the stability fields of the ammines and generally constrains the thermodynamic window for the leach. The Fe(II) ammines are only thermodynamically stable under reducing conditions. Polarization experiments show that these ammines are unlikely to form if oxygen is present. Fe-Ni-Co alloy passivation may be alleviated by careful management of potential.

Nov 1, 2011

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By Michelle Pienaar, Musa S. D. Manzi, Thabang Kgarume, Glen T. Nwaila, Raymond J. Durrheim, Abrie Oberholster, Hennie Grobler

The South African Mining, Extraction, Research, Development and Innovation (SAMERDI) strategy was launched in 2019 with the goal of modernizing the mining industry. It comprises three major research initiatives: improvement in the efficiency of extraction and health and safety in current mining operations, development of fully mechanized systems to mine narrow tabular ore bodies in hard rock, and development of extraction systems to break rock without using explosives. The crosscutting Advanced Orebody Knowledge (AOK) program seeks to develop and implement drilling and geophysical technologies that can characterize the rock mass ahead of mining and identify potentially hazardous geological features. This knowledge will be integrated with information derived from seismic monitoring. Mining methods, layouts and rock support systems will be adjusted accordingly to mitigate the risk of rockbursts. Boreholes are routinely drilled ahead of mine workings using diamond-impregnated bits. The drill core is logged to identify lithology and geological structures (especially dykes and faults that may be seismogenic), sample the ore body for grade control, and detect areas that may contain water and/or flammable gas. Methods and technology to improve the efficiency of drilling and maximize the information obtained from the drilling process, borehole core, and the borehole itself are being investigated. A range of geophysical technologies are being developed to map the rock mass from the skin of the excavation to a distance of several tens of meters. Light Detection and Ranging (LiDAR) is used to map the geometry of the excavation, including prominent joint, vein and fracture sets and the presence and performance of rock support elements and systems. Ground Penetrating Radar (GPR) is used to penetrate deeper into the rock mass and image joints, fractures bedding planes that influence the stability of the hanging and side walls. Image processing techniques known as ‘seismic attributes’ are being applied to the radargrams to improve interpretation. Electrical Resistivity Tomography (ERT) and various active and passive seismic techniques (e.g. Tunnel Seismic Profiling (TSP), ambient noise tomography) achieve even greater penetration into the rock mass. Finally, machine learning is used to improve the processing and interpretation of seismic and radar data.

Apr 26, 2022

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By D. Bahrami, G. Danko, W. Asante

"It is prudent to interpret atmospheric monitoring signals in real-time for checking the safe limits of the air conditions in underground mines. In gassy mines, such real-time evaluation increases the safety of operation. In all mines, the continuous monitoring and evaluation contribute to maintaining air conditions to be within healthy and safe limits. Signal interpretation for safety conditions in mines is difficult for many reasons. An increase of hazardous contaminant concentrations can be predicted by signal pattern recognition, root-cause analysis of rapid changes toward deterioration and forward prediction in time using algorithms and numerical models. This paper focuses on analyzing signal patterns to recognize dangerous trends as well as forward predicting the various environmental and working conditions that may affect safety in underground mines. Efficient numerical ventilation model with heat and gas contaminant simulation components is needed for the analysis of real-time atmospheric monitoring data. Computational speed enhancement methods are discussed and tested in numerical examples, using the Jacobian sensitivity matrices for signal propagation prediction. INTRODUCTION The focus area of this paper is mine safety, related to hazardous atmospheric conditions in a mine ventilation system. Improvements by recognizing safety hazards caused by heat of combustible gases or the accumulation of poisonous gases in a mine are addressed. The recognition of safety hazard by manual evaluation is difficult because of the complex nature of information and the large amount of monitored data from measurement by atmospheric sensors such as air velocity, pressure, hazardous gas contaminants and temperature. In order to recognize problem-causing trends, it is necessary to evaluate continuously individual measurement data from the Atmospheric Monitoring System (AMS) of the mine during their time-dependent variations. In addition, the combined effects of various signal trends need to be simultaneously interpreted in their cross-effects. It is very difficult to foresee the possible outcomes of intertwined signatures of various problems by continuous human observation. For example, a steady, continuous methane concentration measurement together with a sharp drop in barometric pressure from the AMS sensors may be a case for worry in future time due to pressure-induced methane increase from the coal seam or the gob (Danko et al., 2013). This future increase can be predicted by a time-dependent Ventilation Air Model (VAM) and its surrogate Air Parameter Predictor Solver (APPS) model. A calibrated VAM or APPS model can indeed predict a likely methane concentration variation in future time as a function of previous and new air pressure as well as air velocity (Danko, et. al., 2013). Such a future trend, however, cannot be seen from the raw measurement data."

Jan 1, 2017

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

By V. B. Achanti

Reliability of the compressive strength of a coal seam determined in the laboratory is often subjected to debate. Effects of the coal seam's inherent characteristics, specimen preparation, testing procedure, testing condition, and a number of tests often result in drastic variation of the strength data. This paper deals with the development of a testing procedure for determination of coal seam compressive strength in the laboratory. Coal samples from two different coal seams were tested. First, the inherent characteristics of each coal seam such as coal structure, Hardgrove Orindability Index (HOI), Slake Durability Index, proximate analysis, and mechanical properties namely Young's modulus and Poisson's ratio were determined to categorize them in terms of their characteristic severity liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes namely; cylindrical and cubical, were tested to determine which shape produced the least variation of data and reproducible strength values. Third, four loading rates within the static testing range (Le. 0.007 MPa/s (1.0 psi/sec), 0.07 MPa/s (10 psi/sec), 0.34 MPa/s (50 psi/sec), and 0.7 MPa/s (100 psi/sec)) were used to determine an ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics were established.

Jan 1, 1996

By Daniel J. Brunner

The U. S. Department of Energy (D.O.E.) requires that the prospective nuclear waste repository in Basalt at Hanford, Washington, comply with State of California mine and tunnel safety orders. These regulations require that all main fans be installed in such a manner as to permit prompt reversal of airflow. This paper evaluates the requirement of air reversal and the appropriateness of imposing such regulations on the proposed nuclear waste repository in Basalt.

Jan 1, 1988

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By Lina Ospino Ballesta, Oscar J. Restrepo Baena, Juan Diaz Martínez

Artisanal and small-scale underground gold mining in Colombia plays a significant role in the country’s economy, but it faces persistent occupational hazards that threaten worker safety. Despite mining economic contributions, outdated technologies, limited risk management practices, and insufficient regulatory enforcement have led to recurring workplace accidents, many of which have been fatal. This study presents a systematic review of mining-related accidents over the last decade. Through geo-referenced analysis, high-risk municipalities were identified, and the frequency of accidents was correlated with the mining legal status and operational practices of these municipalities. The findings underscore the urgent need for evidencebased interventions that are tailored to the country’s unique mining context. Ultimately, this research contributes to the global discourse on mining safety by highlighting practical pathways to reduce occupational risks and promote safer, healthier workplaces in resource-constrained environments.

Feb 22, 2026

By Drew Bazil, David Smith, Matteo Ferrucci, David Pittman

The Gateway program will provide additional rail capacity between New Jersey and Manhattan. This paper describes how a 70-foot-deep section of cut and cover tunnel was designed to directly support future high-rise towers. The tunnel will link previously completed tunnel sections under Hudson Yards to future tunnels under the Hudson River. The design aims to minimize constraints on future overbuild and future tunnels, while maximizing constructability within a small worksite. The tunnel will pass under the High Line elevated walkway, next to an active rail yard, and close to a subway tunnel. The design was developed by a tri-venture of WSP, STV and AECOM. WSP led the design of major underground works; STV designed utility relocations and the underpinning concept for the High Line; and AECOM designed temporary in-tunnel systems. Construction is expected to start in 2023.

Jun 13, 2023

By Corey Vaughan

Unplanned shutdowns from abrasive wear part failure in crushers, chutes, and slurry pipe assets can cost millions in lost production and reactive maintenance. 2Censor patented sensor technology enables real time abrasive wear monitoring of mineral processing equipment, turning passive assets into smart, data driven components. Wireless sensors embedded in liners and pipework transmit wear data live to operators, allowing for predictive maintenance, safer scheduling, and optimized asset life. This paper will present global case studies showing reductions in downtime, increased throughput, and improved maintenance accuracy. The system is ready to retrofit, neutral to original equipment manufacturers, and proven across more than twelve countries in abrasive wear liners and slurry pipe applications.

Feb 22, 2026

By R. K. Singhal

Optimization of a load-haul system for a surface mine involves two processes. The first is proper selection of mining equipment compatible with the minesite job specifications and the second is an efficient utilization of this equipment. All things being equal optimal productivity and cost is achieved when the capacity of the hauling equipment is matched at all times with that of the loading equipment.

Jan 1, 1986

By P. R. Taylor

A reaction is evaluated by which heated and pressurized water is used to precipitate metal oxides from loaded Kelex 100 complexes. Pure copper oxide (CuO) and pure nickel (Nio) in powder form, and ranging in average size from 12 to 25 micrometers, were found to precipitate from copper and nickel loaded Kelex 100/kerosene complexes, by water heated and pressurized to between 374 and 400 °c and 2170 psig (148 atm) and 3500 psig (238 atm). The precipitation is suggested to result from hydrolysis of the metal, following exchange for the hydrogen in the phenolic hydroxyl of the Kelex 100 structure, enhanced by the conditions provided by heated and pressurized water. The reaction is believed to have the characteristics of homogeneous nucleation and heterogeneous growth. The effects of temperature, pressure, initial metal concentration and seed addition on the kinetics of the process were studied. In addition, characterization studies were performed on the reaction products. A detailed discussion of the experimental results is presented.

Jan 1, 1992

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which enables completely new designs of conventional shell and tube configurations. This article explains the principle and application of this self-cleaning heat exchange technology and also pays attention to an actual case of a revamp of the severely fouling exchangers of a conventional multi-effect evaporator into a self-cleaning configuration. Possibilities for the revamp of conventional exchangers suffering from massive and very hard scale deposits are found in a variety of metallurgical processes, such as: The refining of nickel, the production of alumina from bauxite and many others.

Jan 1, 2003

By Jerome F. Sheldon

The earliest recorded history in the use of belt conveyors in the United States is in O. Evans' "Miller's Guide" published in Philadelphia in 1795. Evans defines a conveyor as a "broad endless strap of thin pliant leather or canvas revolving over two pulleys in a case or trough." (Ref. 1) In this definition, pulleys are being used in a bulk material belt conveyor application. Pulleys used in belt drives can trace their origin back to 1200 A.D. In fact, Engineers had considerable experience designing them into drives transmitting greater horsepower than those used in the early belt conveyors. In belt conveyor application, a pulley's purpose is primarily three-fold, 1) support the belt in directional changes, as designed in the conveyor, 2) transmit driving power to the belt, and 3) guide or train the belt. There are various types of pulleys used in belt conveyor systems and these are thoroughly covered in "Belt Conveyors For Bulk Materials" prepared by CEMA, 1966. For our discussion, however, the most common used in belt conveyors are drive pulleys, snub pulleys, head pulleys, tail pulleys, takeup pulleys and bend pulleys. The drive pulley imparts the driving force to the belt and may be located at the head or discharge end of the conveyor, in return strand, or at the tailor loading end of the conveyor. A snub pulley is located near the drive pulley to provide more arc of contact between the belt and pulley for maximum

Jan 1, 1971