Search Documents

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By John R. Marks

Few if any mines in North America have used exhaust air to remove heat at temperatures above the stope reject temperature. In contrast, the South African mining industry has long taken advantage of this heat removal method. The Homestake Gold Mine in Lead, South Dakota, has reached the point where a large air-conditioning upgrade is needed. Since existing air and water resources are being utilized about as well as practically possible, it was recently decided to install an 8.1 MW(R) (2300 ton) plant in the deepest mining division. Two horizontal bulk air spray coolers will distribute the coo1th to active workings via controlled recirculation. The heat will be rejected to exhaust air in four parallel cooling towers. The number and size of these large direct-contact heat exchangers prompted an investigation into South African planning techniques.

Jan 1, 1987

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The forestry reclamation approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22 m (4 ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes (i.e., greater than 23°) could lead to slope failures, which is one of the issues that the Surface Mining Control and Reclamation Act of 1977 (SMCRA) sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. During this first phase of investigation, there has been no major mass movement of the slope and slope stability analysis indicates that the application of the FRA has little impact on the overall stability of the slope. Mining Engineering, 2011, Vol. 63, No. 12, pp. 55-62. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

By W. C. Brice

A cooperative study was undertaken by representatives of the environmental community, the mining industry, and state government to identify and resolve environmental issues associated with base and precious metal mining in a neutral atmosphere before a commercial mining development is announced. The study included testing Minnesota's as-yet-untried non-ferrous mining regulatory program using three hypothetical mining developments sited in environ-mentally sensitive areas where future mining could occur. Results include identification of critical paths for regulatory decision making, identification of particularly sensitive environ-mental issues that will need continued deliberation before resolution, and characterization of data necessary for environmental review and permitting decisions.

Jan 1, 1990

By Scott Rosenthal, Dave Gilkey, Theresa Stack, Daniel Autenrieth, Ciara Kremer

Jackleg drill operators are exposed to harmful levels of hand-arm vibration (HAV). Anti-vibration handles and gloves provide modest reductions in HAV exposures and forearm muscle exertion from the use of anti-vibration handles and gloves by jackleg drill operators. The goal of this pilot study was to investigate changes in HAV with the use of anti-vibration gloves and handles compared to forearm muscle exertion experienced by operators and measured with surface electromyography (EMG). Five subjects operated the drill under four different cases: no anti-vibration controls, anti-vibration gloves only, anti-vibration handle only, and simultaneous anti-vibration handle and glove use. Muscle exertion was expressed as a percent of maximum voluntary contraction (%MVC) and was compared using Welch’s ANOVA with Games-Howell post hoc comparisons. The case with both anti-vibration controls in use simultaneously (largest grip diameter) was associated with a mean %MVC of 36.13% during operation for all forearm muscles combined, which was significantly higher than that of the other cases (p < 0.05). There were no statistically significant differences in mean HAV exposures. The anti-vibration handle with anti-vibration glove case only increased the maximum allowable exposure time by 8 min as compared to the control case without any anti-vibration controls. These results suggest that the modest HAV exposure reductions from the use of anti-vibration handles and gloves may pale in comparison to the increased muscle exertion resulting from their use, and this trade-off among jackleg drill operators is a potential concern that warrants further investigation.

Jul 12, 2021

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods.

Jan 1, 1999

By D. A. Bulled

• "What does it look like?" - describes the appearance. • "How does it work?" - outlines the operation. e "Why does it work?"- explains the principles. • "What about controls?" - indicates possible automatic systems. • "How is it sized?" - discusses the necessary testwork and evaluation. • "What are the results?" - demonstrates test and operating results. • "What's the benefit?" - concludes with gains for the user.

Jan 1, 1999

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By R. R. Klimpel

The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and the development of coal gasification/liquefaction processes which require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology, Klimpel (1982, 1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variations in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: (1) slowing down of breakage rates, (2) the occasional acceleration of breakage of some sizes, and (3) conditions where chemical additives will increase rates of breakage.

Jan 1, 1990

By Kraig W. Grubaugh

Rapid growth in the rate of surface mining for coal has caused many states to increase the rigor and complexity of their surface mining codes. The promulgation of Federal surface mining standards may cause those states containing Federal land to amend their codes also. Presented is an up-to-date review of these codes with tabular summaries that divide the codes into operative functions. These summaries will be of use to new operators, multiple-state operators, and state officials. Suggestions are made for industrial efforts to present workable and acceptable amendments to these codes.

Jan 1, 1977

By J. F. Snyder

Minor elements determined by atomic absorption spectroscopy include: zinc, cadmium, copper, cobalt, nickel, chromium, manganese, and iron. Of these elements, only three; zinc, cadmium, and copper are found to have been introduced with the ore-forming fluids. Iron, manganese, chromium, and nickel were increased in dolo-stone lithologies when compared to limestone lithologies. The uniform distribution of cobalt suggests this element was neither increased nor decreased during ore emplacement nor during dolomitization of the rocks. Zinc increases adjacent to ore result from leakages into open spaces rather than as pervasive aureoles surrounding ore bodies.

Jan 1, 1977

By W. M. Aubrey

The use of solid fuel in shaft furnaces to indurate iron ore pellets was originally considered a necessary evil, which the industry worked long and hard to eliminate. Since then changes have taken place in furnace design and operating practices that have led us to our suggestion that solid fuel additions could again be used. In essence, what has happened is that the developments which made it possible to operate without solid fuel have also created new operating conditions favorable to the effective use of solid fuel. Because these new conditions* were brought about in part by the desire to eliminate solid fuel and because the development was a gradual one, the industry failed to reassess its position and for years neglected the possibility of returning to solid fuel.

Jan 1, 1967

By James J. Fallon

The industrial minerals industry is defined loosely and a specific list is presented. Criteria by which to judge prospects and examples are provided. General trends of the industry are observed.

Jan 1, 1984

By Lester G. Rollins

Coal today enjoys a dominant position, serving the energy and metallurgical marketed The measure of success in the market place is, and will continue to be, the price per million BTUs or price per ton delivered to the user. The Coal Industry&apos;s remarkable record of price stability since World War II is well known. The next twenty years promise to be equally as challenging. This challenge will be met our president, Mr. Drain, has often stated that, ?The Joy Manufacturing Company is betting that coal will meet the challenge.? To this end, the resources of Joy have been committed to doing its part. Joy&apos;s efforts are directed toward a target which has been defined as: 1. Deliver coal to the user at a price of $.15/MBTU or less. or; 2. Deliver coal to the mine portal at a cost of $1.00 or less.

Jan 1, 1966