Search Documents

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By Bernd Hagenah, Petr Pospisil, Colin Santangelo

This paper explores the profound implications of high-speed train operation on tunnel planning, specifically investigating ongoing high-speed rail projects in California and Texas. The paper delves into the crucial considerations for designing high-speed rail tunnels, including selecting tunnel sections based on aerodynamic factors, which impacttraction power requirements and pressure comfort. The paper also examines the need for emergency stations, maintenance access, and comprehensive safety and rescue concepts to address train incidents. Drawing from international high-speed rail projects, it shares valuable experiences and lessons learned to promote efficient and secure tunnel designs for high-speed train operations.

Jun 23, 2024

By Donald D. Murphy

My first contact with underground, bolt conveyors came when I was hired as a draftsman by the La-Del Conveyor & Manufacturing Company in 1935. At that tine relatively few nines were using haulage belt conveyors. Wore they were in use, they were usually loaded by chain or shaker type room conveyors which in turn were hand loaded at the working face. Duo to the low room tonnage, a gathering belt might receive who output of from six to eight rooms. For several years belts 26 and 30" in width were the favorites for coal mine use. Belt speeds very seldom exceeded 200 ft. per mm. at that time. Conveyor lengths for the majority of units lay between 1.000 and 2000 ft. For a number of years 25 H.P. drives were adequate for those conveyors. From 1940 until about 1950 loads and speeds went up slightly and 40 H.P. drives became the standard. Since the majority of mines were then using direct current power systems, we were able to use controllers with 3 or more steps of starting resistance. The slow belt speeds coupled with relatively long starting cycles kept the rate of acceleration low and gave us smooth, easy starts.

Jan 1, 1963

By Mustafa Kumral, Yuksel Asli Sari

Underground mining operations are sensitive to price fluctuations because they usually perform with a narrow profit margin compared to open-pit mining. Furthermore, the economic evaluations regarding operation are based on estimated or simulated grades rather than actual values. These bring a high degree of uncertainty to the viability of an operation. Hence, mine planning that accounts for uncertainty is crucial for underground mining operations. As an underground mining technique, sublevel stoping has geotechnical, curing time, seismicity, cost minimization, and production requirements. A new mixedinteger linear program is proposed that considers the uncertainty associated with net present value using chance-constrained programming. The net present value (NPV) maximization objective is transformed into a multi-objective maximization problem where one objective is to maximize the mean NPV, and the other objective is to maximize the negative standard deviation multiplied by a scalar called risk or reliability level. The balance between the two objectives was maintained by this scalar and was selected based on the reliability level of the project. A case study was conducted with varying reliability levels, and sequences were generated. It was shown that the expected net present value increased at higher reliability levels, and the overall value of the objective function decreased as the reliability level increased. In other words, the variance component penalized the value of the objective function. Moreover, it was observed from the case study that at lower reliability levels, stope grade order bears similarity to the extraction order.

Aug 4, 2023

By C. St. J. Lowe

Weir Minerals ? Linatex has developed a new approach to the dewatering of fine solids, particularly mine and process plant tailings and wastes. The Weir process, patented in 2009, uses standard process equipment in a standard flow sheet, but applies this approach to materials previously thought to be too fine to be dewatered with this type of equipment. The process can be applied to a wide range of materials, making lower moisture products that can be re-used elsewhere or sent to disposal. It has already been tested successfully on a small scale in Australia on coal fines, zinc mine tailings, red mud, iron ore tails, and copper/gold tailings. The principal factors affecting the solids recovery have been established as: 1. The % solids in the slurry feed to the process ? a higher % solids provides a higher recovery. 2. The particle size of the feed solids ? coarser feeds provide higher recoveries. The key factors affecting the % solids in the dewatered product have been determined to be: 1. The particle size of the dewatered product - coarser materials produce a higher % solids in the dewatered product. 2. The height of the discharge weir on the dewatering screen - a higher discharge weir on the dewatering screen also yields a higher % solids. 3. The angle of the dewatering screen. Setting the screen horizontal increases the travel rate, reduces the bed depth and reduces the % solids in the dewatered product. Back-sloping the screen up to 5° reduces the travel rate and increases the % solids in product. Eight plants ranging in size from 3 t/h to 40 t/h have been sold to a range of customers in China, for coal and iron ore tailings treatment. Australia has one plant, a small unit rated at 30 t/h of sand fines, and has recently completed test work on iron ore tailings for a dewatering plant rated at 135 t/h. Additional tests are under way with clients around Australia, to demonstrate the capabilities of this process on specific applications and to provide confirmation that materials can be processed successfully, before moving on to larger scale tests or full size plants. The advantages of the Weir process include - lower moisture in products, uses proven equipment, lower capital and operating costs, lower maintenance costs, reduced power consumption, compact footprint, can be used in parallel or in series with existing equipment, modular design to facilitate redundancy or expansion, efficient water recovery and simpler water management, reduced cement in backfill mixes, smaller tailings disposal footprint, reduced earthworks requirements, much lower seepage losses, more stable tailings mass, progressive site rehabilitation, reduced impact on local wildlife, reduced risk of dam wall failure, and reduced environmental monitoring and compliance costs.

Feb 23, 2014

By V. Montaruli, A. Nieto, M. Cardu

Nickel is a metal whose workability and mechanical strength at high temperatures and in corrosive environments makes it an indispensable alloying element for the realization of stainless steel, specialty steel, super-alloys, rechargeable batteries and electroplating. Because its main fields of application are key to the development of industry and, thus, to society, nickel has recently been recognized as a potentially critical mineral, despite its abundant reserves. The purpose of this paper is the creation of possible case scenarios determined by factors and events that, in the medium to long term, could change the current structure of the nickel market on the demand and/or the supply side. Four scenarios have been determined by considering a demand variation due to the occurrence of a natural disaster and an aerospace plan implementation and taking into account the resource nationalism and the skills shortage as supply varying factors. Through the creation of a georeferenced global nickel database, the paper proposes supply strategies related to the four scenarios for each top nickel consumer: China, India, European Union, United States and Japan.

Jan 1, 2013

By Xie Longshui

INTRODUCTION The gold production is from the state-owned gold mines, the local gold mines and the by-product of metal mines. Since 1975, the small gold mines have developed in rapid strides. Currently, there are about 3000 small gold mines in China. Most of them are operated by the local, and the production is about 50% of China&apos;s gold output. In the small gold mines, the normalized mining equipments are employed at most of mines, but some mines still use such backward tunnelling and mining tools as pick, shovel and hand hammer etc.. The mining techniques have developed from the primitive to the advanced, especially the methods of open stope, shrinkage and filling have been widely used. Such new mining techniques as bolting, vibrating draw, non-electric ignition and diamond drilling etc. are also introduced in the wall gold mines. In recent years, the development of small gold mines is very fast under the guidance of new mining policy which is &apos; rapid and great development of large-sized mines, helping small mines to develop, and quick mining for the existing mines; and encouraging the collective and the individual to operate a mine.&apos; GEOLOGICAL FEATURES The gold veins are dominant, which are divided into two types, ie. the mesothermal deposit with altered rock in a crushed zone and the hypothermal deposit with quartz veins. The orebody distribution is not centralized, and the size of deposit and single minable orebody is small respectively. Most of deposit dip at 30° to 50°, characterized by expansion and shrinkage, ramification and compound, thinning out and reappearance, separation and composite at the parallel veins etc.. The ore grade is variable, and the factor of grade change is above 100%. The waste zones with lean or submarginal ore usually exist in deposits. As for the gold deposits with altered rock, the ore boundary is indistinct. Most of gold deposits, particularly the gold deposits with altered rock, are intruded by the late structural rock, thus the faults and joints are developed, and the rock and ore are crushed, especially the host rock of roof wall is very crushed. It ie obvious that the conditions of both formation of deposit and mining are considerably complicated. HISTORY With a long mining history and rich experiences, the local gold sectors are small, but they play an important role in China&apos;s gold mining industry. Dated from Xia and Shang Dynasty, the gold goods was made. In the Tang Dynasty, the development of gold mining industry was very fast. A Chinese poem , written by Liu Yuxi -- one of famous poets in the Tang Dynasty, says: As sun is shining over Dengzhou land, The fog on river slowly goes away, The panning girls together meet at bay, The beauty&apos;s jewels and stamps of king are gold from river sand. This poem shows the local gold mining was flourishing at that time. In 1888, the local gold mining sectors were all the rage at the moment, and the annual output of gold was as high as 21.5 tons. Since the founding of New China, the development of local gold mining was subjected to several back- sets, but certain advances are made on the whole, especially since 1970. Round about 1970,the simple, backward and indigenous mining was dominant in the small gold mines; for instance, the hand-hammer drilling, the hand-operated winch hoisting and the hand haulage etc.were main methods of gold mining . Up until the late 1970s,great changes took place in stoping, haulage and so on. Currently, some advanced technology and large-sized equipments are adopted in the local gold mines. Generally, the local small gold mining sectors play an important role in development of China&apos;s gold mining industry, and are important and attractive sectors. PRESENT DEVELOPMENT

Jan 1, 1987

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By Michelle Mangione, John Kuyt, Zili Li, Michael Mooney

"Twin bored tunnels are commonly used for a variety of road and tunnel projects throughout the world.A major component of these twin tunnel projects is the construction of connecting cross passages that provide emergency access between tunnels and space for tunnel service equipment. Cross passages can present significant geotechnical risk and technical challenges to a project – support systems must be considered for redistributing loads around the mainline tunnel openings and supporting new loading resulting from excavation activities. Additionally, cross passages pose risks to construction schedule and cost because of their sequencing at the end of construction, so mitigation of schedule overruns can be critical. By observing field instrumentation data records from completed projects, a better understanding of the force development in each temporary structure can be achieved with indication of which structures are the most critical to support ground loads.This article discusses the data obtained during the Brisbane Airport Link construction project, a road tunnel located in Brisbane, Australia. Strain gauge instrumentation data from the precast segmental lining and propped opening steel sets is presented with relation to the construction sequence and local geology. Interpretations and conclusions based on the observed trends are proposed, with several key mechanisms affecting the loading and unloading identified.Brisbane Airport Link project overview. The Brisbane Airport Link project in Brisbane, Australia, connects central Brisbane to the airport located northeast of the downtown with more than 7 km (4 miles) of twin-bore road tunnels, two lanes each, with several caverns, interchanges and access ramps constructed along the alignment to connect to other key routes in the city. The project was executed under a public-private partnership (P3) scheme, funded and operated by the consortium BrisConnections. The main contractors were a joint venture of John Holland and Theiss, while the design was carried out by Arup and Parsons Brinckerhoff.Construction of the tunnels was conducted using a combination of 17 roadheaders and two 12.5-m (41-ft) double-shield Herrenknecht tunnel boring machines (TBM) (Harding & Francis, 2013). The TBMs were used in earth pressure balance- (EPB) type closed mode for the initial portion of their drive, starting at the northeast end of the alignment. Tunneling started in soft ground, weathered rock, and mixed face conditions initially, progressing to competent sedimentary rocks as the drive continued. Support was accomplished using a 12.1-m (39.8-ft) diameter steel fiber reinforced concrete (SFRC) segmental lining installed behind the TBMs in nine segments + one key arrangement. The innovative design of these segments is detailed in the paper by Harding and Francis (Harding & Francis, 2013). Ancillary roads and underground interchange caverns were constructed by sequential excavation techniques using roadheaders, accounting for nearly half of the total underground excavations."

Mar 1, 2017

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit&apos; becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By R. L. Braun

In situ chemical mining of primary sulfide ore requires distribution of injected oxygen in a large underground flooded region of broken ore. Although the maximum oxygen content of the leach solution will be dictated by the operating temperature and hydrostatic pressure, the actual oxygen content will be limited by the geometric dispersion of the injected oxygen, the rate of dissolution of oxygen, and the rate of convective circulation of oxygenated solution within the flooded bed of ore fragments. These factors are examined by a detailed theoretical analysis supported by laboratory experimental data. Typical results of the study illustrate that adequate dissolution of oxygen and circulation of oxygenated solution can be obtained in a column of 4 million metric tons of broken ore by using three gas injection lines and an oxygen injection to consumption ratio of 1.84.

Jan 1, 1974

By Thomas F. Evans

Niagara Mohawk, like other northern coal users, has long experienced increased costs during winter months as a consequence of handling frozen coal. These costs include operating labor, maintenance labor and materials, equipment rental, fuel for thawing, demurrage, carrying costs for excess coal inventory and substitution of higher cost electrical generation for lost production capacity. In the winter of 1978-79, limited trials of several coal freeze conditioning agents were made to determine whether these would provide a cost-effective means of reducing the problems of handling frozen coal. Since these trials were generally effective, the Coal Purchasing Department arranged that all rail coal received during the 1979-80 winter from early December to mid March would be treated at the mines during loading. Inasmuch as the treatment costs are themselves appreciable and our various coal suppliers made a variety of choices of chemical supplier and equipment for application, an attempt was made to evaluate the unloading performance of each train received at the two generating stations which use coal as an aid in the future optimization of the use of freeze conditioning agents. These stations also receive coal by truck but this coal is not treated because of the short hauling time. The C.R. Huntley Station in Tonawanda, NY has a capacity of 800MW and burns about 5000 tons of coal per day during the winter months. The coal is primarily from central and western Pennsylvania but one source in southern Kentucky is also used regularly. Most of the Pennsylvania coal is washed and the fines are thermally dried. The coal is delivered in unit trains made up of mixed cars of 60, 75, and 90 ton capacity. Time between loading and arrival at the station averaged five days and ranged from three to eleven during the 1979-80 winter season.

Jan 1, 1980

By M. Yekich, W. R. Reed, G. Ross, M. Shahan

"Canopy air curtains on roof bolting machines have been proven to protect miners from respirable dust, preventing their overexposure to dust. Another desired application for canopy air curtains is in the compartments of shuttle cars. The challenges faced in developing the design of canopy air curtains for shuttle cars include mine ventilation rates in tandem with the shuttle car tram speeds. The resulting cab airspeeds may exceed 182 m/min (600 fpm), as found in the present study conducted in a central Appalachian underground coal mine by U.S. National Institute for Occupational Safety and Health (NIOSH) researchers. Prior research and laboratory testing had indicated that successfully protecting a miner in high air velocities is difficult, because the clean air from the canopy air curtain is unable to penetrate through the high-velocity mine air. In this study, the dust concentrations to which a shuttle car operator was exposed were measured, and air velocities experienced by the operator were measured as well using a recording vane anemometer. The results indicate that the highest exposure to respirable dust, 2.22 mg/m3, occurred when the shuttle car was loading at the continuous miner, where the average airspeed was 48 m/min (157 fpm). While tramming, the operator was exposed to 0.77 mg/m3 of respirable dust with an average airspeed of 62 m/min (203 fpm). This study indicates that a canopy air curtain system can be designed to greatly reduce an operator’s exposure to respirable dust by providing clean air to the operator, as the majority of the operator’s dust exposure occurs in air velocities slower than 61 m/min (200 fpm). IntroductionThe U.S. National Institute for Occupational Safety and Health (NIOSH) issued contract #200-2015-63485 to develop a canopy air curtain for coal mine shuttle cars with Marshall University and J.H. Fletcher & Co. (Salem, Begley and Ross, 2016). The proposed design maintains a design similar to that of a roof bolter canopy air curtain by providing filtered air through a blower over the operator. The plenum, which will provide uniform airflow over the operator, is anticipated to be built into the shuttle car canopy. One of the main interferences with a canopy air curtain is ventilation airflow perpendicular to the plenum airflow (Engel, Johnson and Raether, 1987). This ventilation airflow can shear the downward flow from the plenum, and this shear can reduce the effectiveness of the canopy air curtain by either disrupting the downward flow or allowing contaminated mine air into the canopy air curtain zone of protection."

Jan 11, 2018

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By R. E. Pennington

My subject this morning is coal liquefaction technology. Actually, coal liquefaction involves a number of technologies in a very complex system. The first slide shows the major components of such a system with arrows to indicate appropriate flows. The components are the facilities for coal feed preparation and handling; the coal hydrogenation or base liquefaction section; facilities for product separation and recovery, and in addition, facilities for the production of hydrogen from coal-based sources. A very rough break- out of the investments involved in these areas is given at the bottom of the slide. Investment is spread about equally among the three areas of operations Another way of looking at it is that the investments in what might be called support facilities are of the same magnitude as the base investment in the hydrogen facilities. Therefore, it is appropriate in a discussion of coal liquefaction technology to treat it as a system composed of a number of technologies. The next slide lists the various functions in the feed preparation section along with an indication of technology status. Storage, crushing, grinding, drying of coal all have been in commercial practice for a number of years. The slurrying and pumping of coal at least in water slurries, is practiced commercially also. The heating of coal slurries in oil to high temperatures under pressure is not in commercial practice and development and testing is going on by a number of people in this area. Some rather complex phenomena occur when coal oil slurries are heated to high temperatures.

Jan 1, 1975

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By H. H. Richards, Ray L. Tobie, L. A. Thomas

GENERAL DESCRIPTION Since the beginning of operations, with the exception of a small tonnage mined by slushing, ore extraction has been by full gravity caving. Formerly, a checkerboard sequence of block undercutting was followed with the even-numbered blocks in one panel and the odd¬numbered blocks in the adjacent panel being mined. As these blocks were depleted, the intermediate or pillar blocks were mined (Fig. 1). Following this checker¬board, the mining sequence went through a number of changes, finally evolving into diagonal retreat panel cav¬ing by blocks (Fig. 2). The numbers in Fig. 2 indicate the sequence in which blocks were undercut. Gaps in the numbering sequence indicate undercutting on the level outside the illustrated area. Geology The ore body is a low-grade deposit of chalcopyrite mineralization disseminated throughout structurally weak, highly fractured, strongly altered granitic host rocks. It takes the shape of a gently dipping elliptical cylinder consisting of an ore shell of variable thickness surrounding an interior waste core. Major and minor axes of the mineralized cylinder are 1524 m (5000 ft) and 762 m (2500 ft), respectively, and length approximates 2438 m (8000 ft). Ore is sufficiently fractured to break readily into medium-coarse size. The igneous rock complex containing the ore body is covered by a wedge-shaped blanket of Tertiary con¬glomerate which was brought into place by faulting along the major regional structure of the San Manuel fault. Thickness of the conglomerate cap varies from only 9 m (30 ft) at the east end of the ore body to more than 610 m (2000 ft) at the west. Structurally, the con¬glomerate is much more competent than the igneous host rocks and, when caving, it breaks into massive chunks. Conglomerate boulders seen in drawpoints underground are very coarse. The total rock column over the initial mining area of the 1415 grizzly level was 354 m (1160 ft) of which 122 m (400 ft) was ore, 79 m (260 ft) was leached igneous capping, and 152 m (500 ft) was conglomerate above the San Manuel fault. Diamond Drilling: From 4572 to 7620 m (15,000 to 25,000 ft) are drilled annually from underground workings to delineate the ore body. MINE DEVELOPMENT Haulage Level In the south or main ore body (see Figs. 3-6), with the exception of the draw and transfer raises, all the extraction openings are concreted (Seaney and Tobie, 1965). The haulage panel drifts, which are 18 m (60 ft) below the grizzly drifts, are first driven with pre¬concrete ground support. The drift, which has an arched section, then is concreted using mobile collapsible steel tunnel forms. The haulage drifts leading from the pan¬els to the hoisting shafts are not concreted. After the panel drifts have been concreted, the raise stations from which transfer raises will be driven are constructed and the raise-station ore-drawing chute is installed. The chute is prefabricated of A-36 steel with undercut guillo¬tine gates made of abrasion-resistant 2.5-cm (1-in.) steel plate powered by 20-cm (8-in.) air cylinder installed on each side of the raise station. Transfer Raises The transfer raises are lined with 15 x 20-cm (6 x 8-in.) cribbing and are 1.22 m (4 ft) in the clear. Each cribbing is protected from wear by a high carbon steel angle which is nailed onto the cribbing. The transfer raises are driven from each side of the raise station on an angle of 1.1 rad (63°). Each raise con¬sists of a main and a backover branch. The transfer¬raise driving crew consists of two men working one shift only. Grizzly Drifts After the transfer raise reaches the grizzly level, the grizzly drift can be driven. The grizzly drifts are spaced at 10.6-m (35-ft) centers and are driven parallel to the long axis of the ore body (see Fig. 2). This drift is driven by a two-man crew working on one or more drifts at a time using feed-leg machines. The eight grizzlies in the 42.7-m (140-ft) long drift are spaced at 5.3-m

Jan 1, 1982