Search Documents

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By James R. Jones

It has been 2-1/2 years since the Congress passed the Surface Mining Control and Reclamation Act of 1977 (PL95-87) the Office of Surface Mining every deadline specified in the Act. Hopefully the Congress will begin to realize that specifying unrealistic deadlines does not accomplish the end desire of legislation any sooner -- it only adds to the confusion, and actually hinders orderly, efficient progress. OSM has been sued by all categories of involved parties -- environmental activitist organizations, the states, and the coal operators. This situation has resulted for two reasons: (1) insufficient time was allotted by the Congress to properly develop the regulations and program, and (2) OSM?s philosophy that it must dictate every detail of reclamation operations from Washington, even though many of its people are inexperienced with coal mining. These law- suits are now demonstrating their value. OSM is showing signs of "pulling-in-its horns" and, hopefully, will approach the revised regulations in a more realistic fasion.

Jan 1, 1980

By Sadatoshi Ohmori, Simin Zhai, Devini Abeyawardena

A road tunnel is planned to be constructed in soft, high overburden ground of around 600 m in Japan by using the center drift advancing method. The dodging effect and early ring closure of the center drift were expected to reduce the displacement and deformation of tunnel and promote safe construction. The measurement result during construction was analyzed and those effects, which the displacement and deformation after the widening excavation decreased and its effect increased as the center drift radius increased, were confirmed by numerical analysis. Also, the effect of the early closure of center drift after widening excavation did not have much effect.

Jun 23, 2024

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By A. E. Halim, J. F. Brune

Debate continues over whether barricading in refuge chambers is a good strategy to survive entrapment emergencies in underground coal mines, in particular fires and explosions. Unlike U.S. coal mines, Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes the merits and problems of using refuge chambers or self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. We found that using refuge chambers may not be the best strategy during extensive fires or when multiple explosions occur. In these situations, mine rescuers are unlikely to be able to extract miners who are sheltered in chambers and, conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as the level 1 emergency exercises required in Queensland, Australia. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Jan 1, 1997

By Peter Zhang, Daniel Su

Following the first longwall excavation at a deep-cover gas well site, the pre-mining modeling prediction of longwallinduced casing deformations in the fully cemented production casing were in excellent agreement with post-mining Caliper survey results. However, after second panel mining, the post-mining Caliper survey revealed a large plastic deformation near the top of the Pittsburgh Seam. The focus of this paper is to identify the possible cause of such an anomalous deformation. Very high longwall-induced casing stress near a thick claystone layer at 23 feet above the Pittsburgh seam horizon was identified as the primary cause. Leaving the production casing uncemented or using softer cementing material between intermediate and production casings is identified as the best practice.

Feb 1, 2024

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

By E. Milosavljevic, C. H. Bucknam, K. L. Gabby, T. C. Eisele

"Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately, mercury is recovered along with the silver as mercury/silver/gold amalgam, which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution. IntroductionThe dissolution of mercury along with precious metals during cyanide leaching is a long-standing problem, which can result in significant mercury toxicity issues (Washburn, 2003). Mercury is first dissolved by the cyanide solution, and then, since it has a great deal of chemical similarity to silver, it follows silver throughout the concentration and recovery processes, ultimately being recovered as a silver/ mercury amalgam when the metal is precipitated by either the Merrill-Crowe process or by electrowinning.While it would be desirable to either prevent mercury dissolution entirely while still allowing silver dissolution, or to selectively capture mercury before the precious-metals recovery step, there is not yet an effective and economically practical approach to doing this (Grosse, 2003; Ravichandran, 2004; Misra, 1998; Pai, 2000). There are a few processes that have been proposed, such as differential adsorption. While activated carbon, as used in the carbon-in-pulp process, is not highly selective between mercury and silver (Washburn, 2003), it may be possible to achieve some separation by selective elution of the carbon to produce high-mercury and low-mercury eluates (Bunney et al., 2010). Certain synthetic resins were shown to be selective for gold but are more expensive than carbon, requiring special equipment, and have not yet been shown to be selective for mercury (Grosse, 2003). There may be potential for differential dissolution approaches, as thiosulfate leaching does not dissolve mercury sulfides as readily as it dissolves gold (Oraby et al., 2010), and it is possible that it may be similarly more selective for dissolving silver relative to mercury. Some work has also been done with selective precipitants, such as sodium polythiocarbonates (Bucknam, 2007), and 1,3-benzenediamidoethanethiol (Matlock, 2002). Common problems with these approaches include introduction of a solid:liquid separation step, reagent costs, the need to measure the mercury concentration for process control for minimizing silver losses, and regulatory requirements to retort otherwise stable mercury concentrates."

Jan 1, 2015

By O. K. Brown

U.S. Borax has two tailings disposal requirements which are uniquely different in many respects, but with the common goal to minimize the impact on the environment, utilize dependable technology and minimize the economic impact. The existing borax mine in the grid Mojave desert of Southern California has gone through a series of changes in tailings disposal practices in the 56 years of operations, The other tailings disposal requirement is a new molybdenum mine, presently in the feasibility phase, in the high precipitation setting of Southeast Alaska. II. Introduction U.S. Borax is faced with two tailings disposals situations, at diverse locations:

Jan 1, 1984

By J. B. Davis

Isotope analyses distinguish biogenic sulfur ores from non-biogenic ores, but do not distinguish bioepigenetic from biosyngenetic ores. Sulfur deposits of salt dome caprocks and of bedded Permian evaporites of west Texas, however, are clearly bioepigenetic. Anhydrite, introduced by salt diapirs into geologically younger sediments, is converted biogenically to sulfur and calcite in the presence of petroleum; for example, in Challenger Knoll, a salt dome at a water depth of 3600 m in the Gulf of Mexico. Bedded evaporites of west Texas in association with petroleum show an obvious epigenetic replacement of the anhydrite layers by biogenic sulfur and calcite

Jan 1, 1978

By Bruce E. Kester

The concurrent observation of the phenomena of alkali-aggregate reaction and development of efficient dust collection systems on rotary kilns made mandatory the process modifications to produce low alkali cements. Such low alkali cements as were available prior to these recent changes were either the rare result of low alkali raw materials, the loss of alkalies with dust loss from the kiln stack, or in some instances by the use of CaC12 in the kiln feed to increase volitalization of the alkalies and their subsequent loss or discard with the normal dust emission from the kiln. The relative slowly soluble nature of natural occurring alkali minerals in cement raw materials as compared to the very soluble nature of the alkali salts as present in cement kiln reaction products, either in clinker or in dust emission led to the development of the water leaching system. Two distinctly different problems of leaching are created by the two major systems of portland cement production, the wet and dry processes. The wet process is characterized by moderate dust loads and concentration of soluble forms of alkali in the dust. Further the return of the leached dust slurry does not materially change the characteristics of kiln feed on reintroduction and subsequently does not materially influence kiln operation. The dry process differs in high levels of dust emission and the presence in the collected dust of large amounts of unreacted kiln feed with its sparingly soluble alkali minerals. In the dry process reintroduction of leached dust slurry changes the dry process to what may be classed as a damp process. This change results in some decrease in kiln capacity and creates conditions of operation which are uncommon to either the wet or dry process.

Jan 1, 1963

By D. C. Yang

A practical and economical flowsheet has been developed and demonstrated by integrating the packed column flotation with the GranuFlow process for fine coal recovery. Orimulsion, which was used as an additive, served a dual purpose: first in the flotation and second in the dewatering and granulation steps. The test results on the coal preparation effluent sample show that Orimulsion is flexible and compatible with fuel oil and various frothers used in the packed column. Clean coal with ash contents of 3.0, 3.7, 4.3 and 5.1% were produced from a head sample of 33% ash at combustible matter recoveries of 72.4, 81.1, 87.5, and 89.2%, respectively. Other advantages include high throughput, low moisture, improved handleability, and reduced dustiness of the dewatered coal, thus providing a very significant economic Incentive for the integrated process.

Jan 1, 1998

By Bruno C. Boik

INTRODUCTION Cost Management is the evaluation and control of project scope, budgets, and costs with the objective to minimize costs and maximize the benefits to be derived from the use of project resources in conformance with Criteria stipulated or approved by the Owner. In order of importance, Cost Management is one of the most prominent Project Management functions because of its impact on the financial success of the venture. Cost Control and Cost Accounting are essential parts of Cost Management. The principal objectives of Cost Control are to monitor project commitments and expenditures, and measure performance for the detection of variances from acceptable standards and from control budgets so that timely action can be initiated to minimize costs. Cost Control is evaluation of current costs and projection of future costs, rather than the reporting of actual costs. Cost Control is not Cost Accounting. The primary objectives of Cost Accounting are the determination, classification, analysis and reporting in useful detail of actual costs. Following are some considerations on Cost Management and Cost Control as practiced by Owners and Contractors of industrial projects, Mining and Metallurgical projects in particular. COST MANAGEMENT Functions Conforming with the requirements of Owner's Criteria, the principal Cost Management functions are to • evaluate estimates of project costs and establish budgets for a scope of work and schedule; conversely, evaluate the scope of work that can be executed most effectively within a budget and schedule. • promote investigations and comparative evaluations of alternate designs and plans to find the most cost effective way to execute a project and minimize its operating costs. • based on Cost Control and Cost Accounting input, evaluate and initiate appropriate actions to correct deviations from approved budgets. assess project economics, the effect of changes on project economics and, if necessary, revise Project Criteria to modify their impact on costs.

Jan 1, 1986

By J. -M. Lopez-Cuesta, C. Petter, B. Otazaghine, M. Batistella, R. Sonnier

"Kaolinite is a dioctahedral aluminosilicate widely used as paper filler and coating pigment. At the best of our knowledge, kaolinite is not widely used in polymer industry. Therefore, in this study, the flame retardant effect of kaolinite in ethylene vinyl acetate copolymer (EVA) and polypropylene (PP) were studied and compared with an alumina trihydrate (ATH) and Talc. Cone calorimeter results shows that the weight percentage of ATH in EVA/ATH composites must be at least 50 wt. % in order to reach an improvement in fire retardancy in terms of pHRR. In the case of EVA/kaolinite, even with 35 wt. % the pHRR is largely reduced. Comparing PP/Talc and PP/kaolinite composites at 30 wt. %, both fillers leads to same reduction in pHRR with a slightly better performance for PP/kaolinite composites. In both cases an intumescent behavior of kaolinite composites was observed that could slow the rate of the rising degradation products, allowing radical recombination reactions. Also, it was observed that kaolinite forms a protective layer on the surface of the samples, which could insulate the material. These behaviors (intumescence and formation of a protective barrier) could reduce the transfer of the degradation products to the flame and explain the better performance of kaolinite composites. INTRODUCTION The use of mineral fillers as fire retardants in polymer matrix are well known and widely studied [1]–[10]. Aluminum and magnesium hydroxides (respectively ATH and MDH) are the most widely used inorganic fire retardants. To achieve fire retardancy with these mineral fillers, about 50-60% loading is required which decrease the physical properties of the composites. The fire behavior of composite EVA has been the subject of many studies [4], [7], [9]–[15]. EVA copolymers are commonly used in the cable industry, due to their high ductility, even at high loading rates. In such applications, the flame retardant systems should be introduced into the polymer to improve the fire reaction. Many flame retardant systems have been tested but the most used industrially relates to formulations based on hydrated mineral fillers (aluminum hydroxide and magnesium hydroxide). Their low cost and reduced fumes generation explains their success. However, to obtain good performance with this type of flame retardants, it is necessary to incorporate high levels (up to 65 wt %), which severely impact other properties such as processability and mechanical behavior. The main modes of action of these flame retardants are the dilution of the gas phase, the endothermic decomposition and a barrier effect created by the inorganic oxide residue which may be improved by the incorporation of other components such as montmorillonites, silicas or talcs."

Jan 1, 2015

By Liming Yuan, Wei Tang, RICHARD THOMAS, DAVOOD BAHRAMI

The location and orientation of fire suppression nozzles is critical in suppressing mobile mine equipment fires. To effectively suppress such fires, optimization needs to be considered for the suppression nozzle locations and discharge angle. Detailed experiments were conducted to study the effectiveness of fire suppression agents with different nozzle configurations. A variety of fire suppression systems including dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist were used. Six types of nozzle locations were studied, and their fire suppression effectiveness were compared. Results from this work highlight potential considerations when determining effective fire suppression designs.

Feb 1, 2025

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By W. L. Price

Recent publication of United States Bureau of Mines figures showed that the sand and gravel (3) industry is the largest single mining industry in the United States in term of yearly tonnage produced. The yearly production of over 500,000,000 tons per year now exceed bituminous coal production. This disclosure caught unawares many observers who have not been following closely the rapid-growth of this phase of mining. Along with this steady growth in production, the sand and gravel industry has gone through an accelerated and varied program of beneficiation in a period of the last ten years.

Jan 1, 1958