Search Documents

By Joel K. Witt, Jackson G. Jenkins, Wendy M. Gort, Brent A. Whitman

A major concern for operators of leaching/SX-EW plants is a phenomenon known as gunk or crud. The build up of gunk is typically the result of fine particulates which are transported via the leach operation to the solvent extraction plant. The particulates develop into a solid layer that concentrates at the aqueous/organic interface. This can cause phase separation problems which can result in entrainment and other deleterious operating conditions. Most operations physically remove the gunk from the SX settlers and process it via a centrifuge or coalescer to remove valuable organic. While both methods have served for many years, Magma is currently evaluating the use of a chemical surfactant which induces a definitive separation of particulates from organic.

Jan 1, 1994

By Joseph W. Mussey

Bio-epigenetic sulphur deposits occur in Pecos, Reeves and Culberson Counties of far West Texas. Sulfate reducrng bacteria, utilizing hydrocarbons as energy, transformed gypsum into replacement limestone and hydrogen sulfide. Hydrogen sulfide, retained in the porosities of the replacement limestone, was subsequently oxidized by highly oxygenated groundwaters, and native sulphur precipitated. West Texas sulphur was first recognized at surface exposures by William P. Blake, a geologist attached to the Captain Pope Military/ Scientific Expedition of 1854. Attempts were made in the early 1900's to mine these sulphur vent exposures by a retort method, but the ventures met with little success. In 1967, Duval discovered a large sulphur deposit near some of the old sulphur works in Culberson County. Duval also extended a small sulphur deposit in Pecos County. The Frasch process, developed for producing sulphur from Gulf Coast salt domes, proved successful in West Texas type sulphur deposits also. However, modifications of the process were necessary to provide economical and efficient sulphur recovery from the varied ore modes. West Texas conditions and logistics require the ultimate in productivity to be competitive in the domestic and foreign sulphur markets. Several companies, in addition to Duval, are producing or have produced sulphur in West Texas. As of the first of June 1984, a total of 29.4 million long tons of sulphur had been produced west of the Pecos -aver. Duval produced more than 88 percent of that total.

Jan 1, 1984

By Samuel A. Reipas

Introduction The ore mining industry has been successful because of technological progress and huge sums of capital investment. But new technology and plants have not come cheap. The problem now is companies will run out of money before they run out of ideas. Survival Strategies Industry survival strategies demand restructuring and new plans. Inland's prescription for the future includes: • Continued emphasis on technological improvements to upgrade pellet quality and lower costs; • Effective use of human resources resulting in employee satisfaction and improved planning and productivity; • Deliberate, well planned, and documented cost-control programs for the short- and long-term; and • Capital investments to support the first three initiatives. Technology Technological changes are not only required by the need for operational improvements, but by product quality improvement dictated by the user - usually the blast furnace operator. Established ambient measurements of pellet quality, such as tumble index, compression strength, porosity, size distribution, and chemical composition, are no longer considered meaningful in predicting pellet performance in a blast furnace. New specifications, called low temperature and intermediate temperature properties, have been recently introduced. Low temperature specifications are characterized by disintegration of pellets in the 500°C (930°F) range in the upper portion of the granular zone during the hematite-to-magnetite transformation in blast furnace stack. Intermediate temperature properties (measured by 1000°C or 1800°F) are characterized by swelling, reducibility, and compression strength after reduction, reflecting conditions in the lower portion of the granular zone of the furnace. These new parameters are being used for pellet quality evaluation at Inland, and will be introduced at its Minorca mine for more routine analysis and correlation with the pellet furnace operation. With increased emphasis on quality, effective communication between the blast furnace operator, research, and the pellet plant operator is critical. At Inland, this is accomplished through technical meetings where the opportunity is provided to solve problems, establish a common understanding on the value of quality, and develop future quality standards and programs. With the degree of sophistication in determining pellet quality as it affects blast furnace operation, the future pellet plant operator will actually be producing a custom pellet. Human Resources Technological change has been a strong point at Inland, and will continue to be. However, human resource management is equally important. Is management giving sufficient attention to employee motivation and involvement? It is a way to improve productivity, reduce costs, and enhance employee job satisfaction. The industry is beginning to understand the principles and the potential for tapping employee brainpower. The payoff can be handsome. Management has to be willing to share both information and power if participative management is to live up to its potential. It has to become more flexible and be willing to adapt to change on the human side. Management should embrace rather than fear employee involvement. Given time, joint problem solving will replace adversarial attitudes and pay dividends for both sides. Productivity and product quality will improve and new dimensions of employee job satisfaction will be achieved. But, it will not happen overnight. Attitudinal change must permeate the organization from top to bottom. This change is needed to support the working relationships and give everyone a sense of direct and meaningful involvement.

Jan 11, 1983

By J. Peterson, R. Michael, D. Yantek, E. Ferro

Among underground coal miners, hearing loss remains one of the most common occupational illnesses. To address this problem, the U.S. National Institute for Occupational Safety and Health Office of Mine Safety and Health Research (NIOSH OMSHR) conducts research to reduce the noise emission of underground coal mining equipment, an example of which is the roof bolting machine. Field studies show that, on average, drilling noise is the loudest noise that roof bolting machine operators would be exposed to, and it contributes significantly to the operators’ noise exposure. OMSHR has determined that the drill steel and chuck radiate a significant amount of noise during drilling. OMSHR and the Corry Rubber Corporation (CRC) have developed a bit isolator that breaks the steel-to-steel link between the drill bit and drill steel and a chuck isolator that breaks the mechanical connection between the drill steel and the chuck. This effectively reduces the noise radiated by the drill steel and chuck and in turn reduces the noise exposure of roof bolter operators. This paper documents the evolution of the bit isolator and chuck isolator. Laboratory testing confirms that production bit and chuck isolators reduce the A-weighted sound level generated during drilling by 3.7 to 6.6 dB.

Jan 1, 2011

By James E. Breland

Society's growing concern over the number of deaths and serious injuries occurring in coal mines, coupled with a growing sentiment to develop and promulgate improved mandatory health or safety standards, was no doubt the basis for passage by Congress of the Federal Coal Mine Health and Safety Act of 1969, being Public Law 91-173 approved December 30, 1969. Even prior to passage of the Act, strong reaction was quick to arise concerning the effect of such legislation upon the coal mining industry. Initial response varied from mild forms of criticism to' the expressed fear of complete suspension of operations and mine closings. Primarily responsible for these early forms of skepticism were speculative or fanciful cost estimates which led operators to contemplate a less than prosperous existence. However, in spite of this unfavorable outlook, the majority of the operators have faced up to the situation and have been striving to comply with the Act and the regulations issued thereunder. While encouraging strides have been made toward implementation of the Act, it must be recognized that noticeable results have been attained only through many months of determined effort and, as anticipated, at quite heavy expense to the operator.

Jan 1, 1973

By Abdelaziz Baçaoui, Imane Aarab, Abdelrani Yaacoubi, Khalid El Amari, Abderahman Etahiri

Phosphate ores upgraded by flotation are widely used as vital raw materials for the sustainable production of phosphate fertilizers to maintain the food supply. High-grade phosphate reserves become more and more depleted. Low-grade phosphate mining and processing are in the spotlight of the fertilizer industries to cope with the exponential growth in the world’s population and meet the increased demand for fertilizers. As part of a series of research works conducted within a major project aiming at upgrading a low-grade phosphate ore never-exploited before, the present work endeavors to optimize the flotation of this ore using the response surface method (RSM) as a follow-up of a screening study. Unveiling new insights on such a strategy paved the way for improving flotation performances. This work demonstrated that an optimum 30.18% P2O5 with 88.07% recovery was achieved using 63.10 g/t of sodium alginate (NaAL) and 2484.72 g/t of sodium oleate (NaOL) at pH 11.40. This maximum was contrasted with a new formulation of fatty acids (FAM). The 30.76% P2O5 grade with a recovery of 89.72% was attained using 50.94 g/t of NaAL and 1455.40 g/t of FAM at pH 11.68. FAM collector markedly outperformed NaOL at low concentrations proving the efficiency of synergists.

Dec 7, 2022

By E. A. Martell, K. S. Sweder

INTRODUCTION Lung cancer in uranium miners has been attributed to alpha irradiation of basal cells of the bronchial epithelium by radon daughters, primarily by 7.7 MeV alphas from polonium-214 (Altshuler et al., 1964). It also has been was observed that for a given cumulative radon progeny exposure, uranium miners who smoke cigarettes have an incidence of lung cancer about 10 times higher than nonsmoking miners (Lundin et al., 1969). It has been pointed out that the large excess of lung cancer deaths among smoking uranium miners is a multiplicative effect (Doll, 1971), which suggested possible synergistic interactions between airborne radon progeny and cigarette smoking. Experimental studies of the complex pattern of interactions between radon progeny, cigarette smoke particles, and the cigarette smoking process are in progress in our laboratory. Preliminary results, reported elsewhere (Martell, 1981), implicate alpha radiation from indoor radon progeny in the etiology of lung cancer in all cigarette smokers. Cigarette smoking produces high concentrations of smoke particles of low mobility and respirable size--particles between 0.5 and 4.0 µm in aerodynamic diameter (see below). The attached fraction of indoor radon progeny is highly dependent on the air concentration of small particles from cigarette smoking and from other combustion sources (Martell, 1981). The size distribution and other properties of radon progeny associated with cigarette smoke particles enhances their effectiveness in the induction of bronchial cancer in man. In this paper we discuss the properties of radon progeny associated with cigarette smoke, the fractionation of radon progeny and modification of their aerosol properties in burning cigarettes, the role of 218Po in these processes, the production of insoluble 214Pb and 212 Pb enriched particles in burning cigarettes, and the consequent differences in the patterns of polonium isotope alpha irradiation in the bronchial epithelium of smokers. EXPERIMENTAL PROCEDURES Experimental methods used in these studies involve the use of small experimental chambers of known radon and radon progeny concentrations in combination with aerosol collection and sizing techniques and sensitive radioactivity detection methods. The use of low-level [ß-] counting for radon progeny determination, providing a measure of 214 Pb plus 214Bi activity, makes it possible to carry out chamber experiments with small radon emanation sources and relatively low air concentrations of radon and radon progeny concentrations in the range from 100 to 1,000 pCi per liter. Thus, for example, in a typical experiment we use a 10 nanocurie 226Ra solution standard in a 10 liter chamber, providing an equilibrium concentration of 1,000 pCi of radon per liter. In small sealed chambers, radon progeny plate out rapidly on the chamber walls, with steady-state concentrations of airborne progeny less than 2 percent of equilibrium levels. This is experimentally convenient because, upon introduction of high concentrations of cigarette smoke particles or small particles from other sources, there is a systematic ingrowth of attached radon progeny, providing a tagged aerosol source of known age and radon progeny composition. In some chamber experiments a 226Ra solution standard of small volume, acidified to O.1N HNO3, was used as the radon emanation source. When used with a bubbler the holdup of radon in an 8 ml volume of 226Ra solution standard at 0.1N HN03 was only 2% of the total radon in the chamber at equilibrium. For experiments with 212Pb-tagged aerosols, we used a dry Ba(228Th) stearate emanation source prepared by the method of Hursh and Lovaas (1967). 226Ra and 222Rn determinations were made by radon gas counting. The 222Rn in a sealed air or water sample is transferred, using helium gas as a carrier, successively through a dry ice cooled trap at -80°C to remove water, through ascarite to remove C02, and through a small activated charcoal trap at -80°C to collect the 222Rn. Subsequently, by heating the charcoal to 400°C, the 222Rn is transferred next to an LN2-cooled capillary trap, and finally into an alphascintillation counting cell of the type described by Lucas (1957). As already stated, radon progeny activities were determined by low-level [ß-] counting, which provides a measure of 214Pb plus 214Bi. The radon progeny samples, collected on efficient Delbag polystyrene micro-fiber filters or on impactor foils, are placed in close, sandwich geometry between two thin-walled flow counters inside shielding anticoincidence counters and a 15 cm thickness of steel shielding. This configuration provides nearly 4II geometry and a low background of only 0.25 to 0.30 cpm. Aluminum absorber was added to provide a combined thickness of absorber and counter wall exceeding 7.0 mg/cm2 to eliminate the variable contribution of 7.7 MeV alphas from 214Po. 212 Pb determinations also were carried out by low-level [ß-] counting, in this case using a combined absorber and counter wall thickness of 9.0 mg/cm2 to eliminate contribution of 8.8 MeV alphas of 21 Po. In each experiment the [ß- ]activity data were corrected for decay to an appropriate common reference time for assessment of activity distributions.

Jan 1, 1981

By Morgan M. Sears, Mark Morris, Joseph Bright

In an effort to advance the science underlying modern coal pillar stability analysis, researchers at the National Institute for Occupational Safety and Health are currently involved in research aimed at better understanding the impact of an in-seam rock parting on the strength of coal pillars. The purpose of this study is to determine a suitable virtual mining height that could be applied using current pillar stability analysis tools. To accomplish this, the boundary element model LaModel was used to back analyze data collected on pillar performance in a room-and-pillar panel at the Maple Eagle Mine located in Southern West Virginia. In a previous work, data collected from borehole pressure cells (BPCs) and extensometers were taken from three instrumentation sites. Data collected from the back bleeders were used to measure the rear abutment stresses, and data collected from two instrumentation sites in the wraparound bleeder were used to measure the front and side abutment stresses as well as the peak strength and performance of the slabbed leave pillar. The utilization of two nearly identical instrumentation sites in the wrap-around bleeder provided much needed repeatability of the obtained measurements. In this study, the data collected from BPCs at the three instrumentation sites was calibrated to match the Bieniawski pillar stress gradient. To model the measured pillar behavior, the LaModel program was selected due to its capability of being directly comparable to the Analysis of Retreat Mining Pillar Stability (ARMPS) and Analysis of Coal Pillar Stability (ACPS) programs. The model was then calibrated to match the measured abutment extent and abutment stress. Finally, the model was validated by reducing the modeled mining height until the yielding of the slabbed leave pillars in the model matched what was measured in the field. The final calibrated mining heights show that a reduction of the shale parting thickness, not including any clay layers, of 52% is applicable. This research study provides the first known measurement of the ARMPS/ACPS “50% Rule” and its applicability to this panel of the Maple Eagle Mine. This finding provides a proof of concept and could have significant implications for future research.

Feb 1, 2024

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By R. L. Bleifuss, S. Zhong, H. E. Geotzman

Microwave heating of iron ore was investigated as an alternative to conventional reduction processes to solve the problem of slow heat transfer. Microwave heating and reduction tests were run on composite green balls made from coal and magnetite concentrate. Benchscale tests were run on both powdered and pelletized feeds using a 15 kW microwave generator. A significant increase in the reduction rate was obtained. With 20% excess stoichiometric carbon in the mix, more than 90% reduction of the iron ore can be achieved in about 10 min at temperatures of around 1,000°C. The reduction of iron ore with coal by microwave heating produces a pure, dust free, high-Btu flue gas that can be used in related thermal operations. Depending on the purity, the reduced iron product could be fed directly to an electric arc furnace for melting. In some cases, the removal of a slag phase may be required to eliminate excess silica and alumina.

Jan 1, 1997

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997

By Clifford J. Lewis

The role of calcareous minerals in that area of the environmental improvement program involving the control or elimination of sulfur oxide emissions is discussed, and a new concept in gas scrubbing, rendering possible the use of calcareous rocks more extensively for this purpose, is presented. Calcareous rocks are defined as the more common limestones, consisting essentially of calcium carbonate and magnesium carbonate. The effect of magnesium carbonate on the reaction rate of limestones and lime toward sulfur oxides in aqueous scrubbing systems is pointed out. The relative economics of lime- stone versus lime as aqueous scrubbing reagents for sulfur dioxide are indicated.

Jan 1, 1974

By Graham A. Mathieson

The precise definition of an ultimate or economic pit has, over the years, received much attention in the literature on the subject of mine planning. Unfortunately, relatively little has been published in the area of pit sequencing and scheduling--an aspect which is typically of much greater economic significance both during the life of a mining operation, as well as in the evaluation of an exploration project. This paper discusses an overall mine planning methodology with emphasis on the design of an optimal sequence of pit expansions or phases. Although the concepts given are not new, it is hoped that some practical suggestions will be made. The paper will also describe graphical techniques which have been found useful in comparing the merits and impacts of alternate planning strategies and production schedules.

Jan 1, 1982

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By P. Berendsen

The tectonic and sedimentary environment of the Central North American Rift System (CNARS) provides all excellent setting for major mineral deposits. Major north-northeast-trending high-angle normal or reverse faults and northwest-trending transcurrent fault systems may exercise control over ore forming processes. Gabbro and basalt are the dominant igneous rock types. Carbonatite and kimberlite occur in Nebraska and Kansas. Concentrations of Cu. Ni, Co, Ti, Au. Ag and PG-minerals are known to occur in this setting. Arkosic sandstone, siltstone, shale, and minor carbonate units occur on top of the rift basalts and in flunking basins where they may reach thicknesses of 10 km (6 miles). The potential, for stratiform or unconformity-related metalliferous deposits must be considered. The rift as a whole remains, however, largely unexplored.

Jan 1, 1990

By Ibezim J. Anazia

Electrothermal production of elemental phosphorous (P4) generates substantial amounts of highly toxic phossy water and sludges. Because of their high phosphorous content and lack of reliable processing technology, large tonnages of these hazardous wastes have accumulated from current and past operations. To date, the sludges are stored in ponds or above ground in special containment vessels at various locations around the country. Two samples of electric furnace phosphorous sludge obtained from the Tennessee Valley Authority (TVA) in Muscle Shoals, Alabama and FMC Corporation in Pocatello, Idaho were investigated using physical separation techniques to recover the elemental phosphorous in the sludge and to render the residual material non-hazardous. The techniques tested include sizing, froth flotation and dispersed air oxidation. Flotation and sizing produced concentrates containing 69 -90% P4 with a recovery in the range of 60 -87%. Dispersed air oxidation of the fines and tailing products was effective in removal of an additional 10 -15% of the P4 in the sludge.

Jan 1, 1991

By Shilpa S. Haramkar, Bhaskar N. Thorat, Sachin V. Jadhav

The filtration of phosphogypsum is a ubiquitous step in the manufacturing of phosphoric acid. It is highly desired to achieve the minimum concentration of P2O5 in the phosphogypsum cake. This work is aimed at addressing P2O5 losses in phosphogypsum (PG) along with the recovery of P2O5 from slurry by using constant pressure filtration at 1 bar pressure. Laboratory tests were carried out in the phosphoric acid production plant situated in Paradeep, India. Recycled water source near acid plant (i.e., pond water) was used for cake washing to reduce the burden on fresh water stock. The findings indicated that pressure filtration offered the most effective P2O5 recovery (nearly 93.48%). The moisture was reduced to 14–16%, and watersoluble P2O5 in the gypsum cake was found to be negligible. A narrow particle size distribution was observed, which offered effective filterability with average cake resistance of 2.38 × 1010 m/kg, indicating a moderately separable cake.

Aug 23, 2023

By G. W. Toth

The coal mining cost models described in this paper represent a computerized estimating procedure for analyzing mining costs and requirements of proposed coal mining projects. Both surface and underground mining analyses can be conducted through the use of these models. These models were developed by the NUS Corporation for the Electric Power Research Institute (EPRI). The methodology design of the cost models follows a process engineering approach for determining mining requirements and costs similar to the logic typically employed in preliminary mine feasibility studies. All capital and operating costs associated with a new coal mining project are thereby estimated. The results of these analyses are then entered into a financial analysis framework which computes annual cash flow summaries, utilizing a profit and loss statement approach, to solve for either the coal value/ton (minimum required selling price) or the rate of return on equity for the project. The coal value/ton is also referred to as the economic cost of production (F .O . B. mine, including preparation).

Jan 1, 1980

By Hasan Nizamoğlu, M. Deniz Turan, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings (flotation waste) that is formed during copper production may be considered in the class of valuable wastes due to the amount of copper it contains. Owing to the decreasing grade values in copper ores, utilization of wastes such as tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental sense. This study investigated the usage conditions of five different ammonia salts as leaching reactants for the purpose of selective extraction of copper from tailings. For this purpose, the effects of parameters such as leaching temperature and leaching time were examined at different concentrations of ammonium hydroxide, ammonium carbonate, ammonium nitrate, ammonium chloride, and ammonium persulfate. The copper extraction efficiency in the case of using the aforementioned salts by themselves were listed as (NH4)2CO3 (73%) > (NH4)2S2O8 (69%) > NH4OH (64%) > NH4Cl (42%) > NH4NO3 (40%). The highest copper extraction efficiency was obtained in the leaching process that was conducted with the solutions obtained by mixing ammonia salts in the best conditions. Accordingly, as a result of 6 h of leaching at 30 °C in the presence of 22.5% NH4OH and 100 g/L (NH4)2S2O8, 91.47%of the copper was transferred into the

Jun 3, 2020

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988