Search Documents

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By L. Zhou, D. Bahrami, Y. Xue

Underground mine fires are a threat to the safety and health of mine workers. The timely determination of the location and size of an underground fire is of great importance in developing firefighting strategies and reducing the risk of any injuries. Machine learning was used in this paper to develop a predictive model for fire location and fire size in an underground mine. The ventilation data were obtained by simulating different mine fire scenarios with MFire. The ventilation data of all airways were used as features to predict the fire location. Based on the feature importance, five airways were selected to monitor, and the airflow data of the selected airways were used to predict the fire location and fire size. An accuracy score of 0.920 was obtained for the prediction of fire location. In addition, in-depth analyses were conducted to characterize the wrong predictions with the purpose of improving the performance of the random forest model. The results show that the occurrence of fire at closely connected airways at some locations can generate misleading ventilation data for each other and the model performance can be further improved by grouping them. Fire size is another factor affecting the model performance and the model accuracy increases with increasing fire size. The result from this study can help mine safety personnel make informed decisions during a mine fire emergency.

Mar 2, 2022

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By L. C. E. FEIO, R. RAMSDEN

In many parts of the world deep level mining relies heavily on the use of refrigeration for providing safe thermal underground conditions. The trend in South Africa in recent years has been to locate the refrigeration plants on surface and to use these plants to chill water that is then distributed throughout the mine. The surface cooling installation normally consists of a pre-cooling tower in which water is first chilled before it is sent to one or more refrigeration plants for further cooling. Presently, the majority of these refrigeration plants use CFC refrigerants; however, to conform with the Montreal Protocol, these plants will have to be replaced or converted for use with alternative refrigerants. The optimum design criteria for installations using the new generation of refrigerants will be affected by their characteristics and are likely to be different from those currently in use. In light of these developments the industry is examining a number of alternative systems for future installations including water vapour refrigeration. Factors that affect the decision on the type of refrigeration system to be used in mine installations are reviewed. INTRODUCTION Gold mining has been carried out in South Africa for over 100 years and most of the reserves close to surface have been mined out; this has led to mining taking place at greater depths, approaching 4000 m below surface. One of the consequences of operating at these greater depths is that it is necessary to install refrigeration plants to cool the ventilation air so as to provide safe and healthy working conditions. With the current low precious metal prices there is pressure on mines to cut costs and in recent years there has been considerable effort devoted to the design of more cost effective and efficient refrigeration plants and cooling systems. In the last 10 years there have been many studies into the use of ice for specific applications (Eschenburg et al., 1986; Hemp, 1988 and Ramsden and Lloyd, 1992) and at present there are three ice making plants in operation on South African mines, each of which produces ice in different processes. In addition, detailed design studies have been carried out on the "split ammonia system" (Napier and Patterson, 1992). In this refrigeration system the evaporator is located underground close to where the cooling is needed, whilst the condenser and heat rejection system is on surface. As far as refrigeration plants are concerned the trend has been to move away from standard package units to custom built refrigeration installations. This has given the design engineer greater flexibility in the choice of key components for refrigeration installations. For example both screw and centrifugal compressors are used, the heat exchangers for the evaporators and condensers may be either plate or shell and tube, and in a number of installations evaporative condensers are used. In addition, the following refrigerants are in use, R12, R22 and ammonia. The acceptance of the Montreal Protocol and its amendments by the South African government will restrict the use of CFC refrigerants and it will be necessary to re-evaluate various refrigeration systems, including those that do not use conventional refrigerants, such as air cycle and water vapour systems, for new surface installations. Although new systems and refrigerants are being developed, only the following refrigeration installations will be compared in this paper: - a refrigeration system using R134a which has properties similar to R12 - refrigeration system using R22 or a new alternative refrigerant with very similar properties - an ammonia refrigeration system - a water vapour refrigeration system The benefits of new cooling systems are not discussed in detail, since they are largely mine specific and outside the scope of the present paper. Since the optimum design for an air cycle system (del Castillo, 1988) is dependent on the mine layout, this system is also not included.

Jan 1, 1993

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By P. C. Fletcher, E. Kaya

The Bond grindability testing procedure has been standardized to measure the same grindability values, i.e. Bond work index (BWi), for the same ore when tests are performed in different laboratories or by different operators. This is accomplished by the standardization of mill dimensions, tumbling speed, grinding ball charge weight and distribution, sample ore charge weight in the mill and operating practice. The results of this investigation reveal that the Bond work index grindability values may differ substantially with different standard Bond ball mills. This paper will review the results.

Jan 1, 2002

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By Hans-Henrik Wallin

The stresses in the heads and shell of a grinding mill are largely dependent on the bending moment produced by the trunnion bearing. By using spherical roller bearings in a special narrow housing a short moment arm is obtained and the bending moment is reduced. For large mills a hydrostatic shoe bearing which also gives a short arm, can be used. Spherical roller bearings also require less maintenance and have a long service life. As the bearings are grease lubricated an automatic lubricator is used instead of an oil lube system. Service data from two Swedish mining companys confirm the fact that the above arrangements provide a long service life.

Jan 1, 1979

By S. Painter

The effects of forced ventilation and thermal radiation in open drifts are included in three-dimensional thermal hydrology simulations of a potential waste repository at Yucca Mountain, Nevada. A semi-analytical model is used to calculate the amount of waste heat removed by ventilation air during each time step of the multiphase thermal-hydrology simulator. The model accounts for thermal radiation and changes in air temperature and humidity along the emplacement drifts. The fraction of heat removed by ventilation is time and position dependent.

Jan 1, 2004

By Frank Florez

INTRODUCTION The Magma mine, located at Superior, AZ, some 100 km (60 miles) east of Phoenix, was discovered in 1875, and was originally mined for silver. The property was acquired by W. B. Thompson who formed the Magma Copper Co. in 1910. Prior to 1965, square-set mining and cut-and-fill methods were used to mine steeply dipping veins at Magma. Ore was moved to the chute by gravity in the square-set stopes and by slusher in the cut-and-fill stopes. The stopes were gobbed with waste from the surface and development headings in the mine. The original square-set method of mining was modi¬fied in order to extract replacement ore bodies in limestones that dipped at 0.52 rad (30°) and varied in thick¬ness from 4.6 to 38 m (15 to 125 ft). Mining of these ore bodies was done by starting at the upper lateral ex¬tremities and retreating to the access openings. The timber square sets and cribbing were used as temporary support, the ground being allowed to cave as the mining retreated. It was found, however, that mining in such a manner was very inefficient; safety hazards increased be¬cause of the blocky and fractured characteristics of the ore and the weakness of the hanging wall. GENERAL DESCRIPTION The undercut-and-fill method of mining is now the primary stoping method used at Magma, and no pillars are left for later extraction. Four ore bodies are pres¬ently being mined. These ore bodies (see Fig. 1) dip conformably at 0.52 rad (30°) to the east with the host limestone and shale sediments, their average strike length is about 122 m (400 ft), and their thickness varies from 9 to 38 m (30 to 125 ft). The ore bodies are separated by varying thicknesses of barren rock. Three of them come together at various elevations primarily in the area of the main feeder fault, but there is an apparent horizontal displacement of about 23 m (75 ft) on the main feeder fault which complicates stope layout. The method as originally applied has been modified in order to mine more efficiently ore bodies that are 9 m (30 ft) or more in thickness. The modification was made to mine all the ore at a given elevation before dropping down for the cut below. The advantage of this is that mining is done on a horizontal plane and there¬fore muck removal can be mechanized. Also multiple faces are made available, thereby improving overall min¬ing efficiency. Another major change made was to carry a 6.7-m (22-ft) face when mining the top sill and a 6.4-m (21-ft) face when mining under fill rather than the former standard 3.35-m (11-ft) high face. This change lengthens the mining cycle and cuts mat prepa¬ration costs in half. Stopes are laid out (see Fig. 2) so that maximum mining panels are available and yet one stope crew will not tie up too much of the ore reserve. One stope might consist of as many as 20 panels, and these panels are divided evenly on opposite sides of the extraction cross¬cut. The stope layout is planned so that the maximum tramming distance to the orepass will not exceed 30.5 m (100 ft) on the crosscut and 38 m (125 ft) in the panel. Stope panel distances are sometimes exceeded when min¬ing to the extremity of the ore body. Tramming distance limits are determined by the efficiency of the com

Jan 1, 1982

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By L. W. Swent

Dr. Emrick, honored guests, distinguished speakers, ladies and gentlemen, I am Langan Swent, Vice President for Environmental Affairs and Occupational Safety and Health, of Homestake Mining Company. Today, I appear on behalf of the American Mining Congress, as chairman of its uranium mine health subcommittee. The American Mining Congress is a trade association of several hundred members, which include the producers of a large proportion of the nation's uranium. I've been asked to make a statement of principles for the uranium industry. There are two types of principles that apply to industry in general, and specifically to the uranium industry. Some have external origins and apply regardless of what industry does or thinks. Others are generated by industry itself and serve as goals for the industry. I'll discuss some of each type. I'll limit my statement to those principles related to the subject of this conference--radiation hazards in mining. I won't take your time trying to explain some of the unrelated principles that we must all contend with, such as Parkinson's Laws, Murphy's Law, and the Peter Principle. First and foremost, industry has a sincere interest in the well-being and health of its employees. There are two basic reasons for this. One is a basic respect for human lives, especially those of people we see and work with every day. No one in management wants to carry the lifelong burden of blame for a life lost due to poor working conditions. Most uranium and other mining is done in small communities. Production workers, maintenance workers, service workers, shift bosses, foremen, superintendents and managers all live in the same community. They attend the same churches. They serve together in civic activities. Their children go to the same schools. If one employee in such a community loses his life due to poor working conditions, those remaining know in a daily and intimate way the resulting personal tragedy, usually of a bereaved widow and fatherless children. This sad experience makes the community, including industry management, intensely sensitive to the need for maintaining good working conditions in the mines. But what about the segment of industry that does not live in the mining communities? Corporate and owner's offices are frequently hundreds of miles from the communities where the mining takes place. Many of these people are not personally acquainted with the workers, and there are few close personal ties between the two communities. The distant staff are, however, still human beings and motivated by the same basic human respect for life. Mr. Manuel Gomez of MSHA and a member of the planning committee for this conference summed this point up expressively when he told me: "No one group has a corner on compassion." In addition to compassion, there is another factor. In both communities the basic assignment to everyone is to produce profits. In carrying out this assignment, supervisory and management people are acutely aware of the high cost of illnesses and accidents. Their objective of maximizing profits is advanced significantly by minimizing illnesses and accidents at the mines. A business that has illnesses and accidents generally suffers from poor employee morale and high employee turnover, both of which detract from profits. Next, I would like to talk about what industry has done in the field that is the subject of this conference. We have worked at all sorts of methods to reduce exposure of employees since the exposure standards were first introduced and then lowered. Other speakers will go into details of technology, and I'll simply comment on exposure results. These are best shown in Table 1. The table shows the average WL to which miners in U.S. underground uranium mines have been exposed since 1937 through 1980. The trend of decreasing radon daughter concentrations throughout the period is obvious. Figure 1 presents this data graphically and shows the trend at a glance. This record begins in 1937 when uranium, as such, really wasn't being mined or sought. The concentrations given by the U.S. Public Health Service were for a few small vanadium mines which carried uranium as a by-product. A few years later, when the Manhattan project to develop the atomic bomb was begun, these mines became the first U.S. uranium mines and the vanadium became the by-product! The radiation hazard then also received attention and the average concentrations began to decline. As knowledge of the reality of the hazard spread, conditions improved. The search for uranium in the U.S. turned up new and larger ore bodies that had to be mined by large underground mines. These mines involved ventilation planning from the beginning, and when they came into production in the late 1950's they lowered the average concentrations greatly. Then in 1960 the American Standards Association adopted a standard setting 1 working level as a satisfactory condition, and several action levels up to 10WL, at which point removal of people from exposure was called for. As a result of the uranium producing states governors' conference in December 1960, state mine inspection agencies, in the early 1960's, began to adopt and enforce the ASA standards. As a result, average concentrations again declined. In 1967, the Federal Radiation Council recommended an annual limitation of 12 WLM per individual. This represented a great change in the methods of

Jan 1, 1981

By W. B. Hayes

The origin of the titanium pigment and metal? industries began with the discovery of the element titanium in 1791 by an Anglican clergyman named William Gregor. The titanium was discovered in magnetic black sands found in the beaches near Cornwall. England. The name titanium was established by the German chemist who discovered the mineral rutile in Hungary. Rutile is the oxide of the element titanium, which he called titan alluding to the mythological titans, giants of ancient Greece. The commercialization of titanium minerals began probably in 1916 with the production of titanium tetrachloride which was to be used in tracer bullets, flares and smoke screens during World War 1. In the 1920's composite pigments based on TiO2 barium sulfate and calcium sulfate were produced, followed by the introduction of the sulfate process anatase TiO2 crystal in the 1930s. The U.S. Bureau of Mines in 1938 began investigating titanium metal technology and promoted the development of the Kroll process. which is the magnesium metal reduction of titanium tetrachloride to produce titanium metal sponge.

Jan 1, 1989

By S. D. Rosenthal

"This article will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia and the journey within academia going into the second year.As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. mining engineering degree in May of 1982, my first job with Utah International in the Farmington, NM area took me back to my home state of New Mexico. Some of you will remember that the early 1980s was not a period of prolific opportunities for mining engineers, given low commodity prices, especially for copper (for example, Anaconda Co. had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton).Gold was taking off in the mid to late 1980s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia. So after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma Copper purchase, Beanup and HBI) and was reviewing assets and staffing, so internal opportunities became scarce. Employees were encouraged to “leave the company and find work elsewhere.” So, off I went to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, AZ, and a posting with Phelps Dodge (now Freeport- McMoRan). After 12-plus years without living close to snow, we moved to the Denver, CO area in a new position with Newmont Mining Corp. Along the way I became a professional engineer (Nevada) and completed a masters in project engineering and management. After 11 years with Newmont, I moved to Butte, MT where I accepted a position as assistant professor of mining engineering."

Jan 1, 2015

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By J. Kretschmann, R. Amiri

"The Sangan iron-ore mines (SIOM) in Iran are located in a remote area, near the Afghanistan border. The deposit of SIOM is containing a geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61 %. The Iranian government plans a stepwise development of SIOM in cooperation with private companies to satisfy the growing demand of the Iranian steel industry. Sustainable development (SD) is an influential ethical concept in mining all around the world. However, a successful realization of a SD is not possible without a foundation on the core values and regarding the specific circumstances of the individual mining country. This paper introduces SIOM and describes SD activities undertaken during its development. From the early stages, these activities have been realized to secure the acceptance of the stakeholders in the region. To evaluate their effects, indicators could be filtered as the ones with the highest priority for the stakeholders. Moreover Islamic values and Iranian regulations and their influences on SIOM have been analyzed. Keywords: Iran, Sustainable Mining, SIOM, Evaluation, Islamic Values INTRODUCTION Mining Industry in Iran The Islamic Republic of Iran holds 68 types of minerals, including salt, sand and gravel, gypsum, chrome, lead, zinc, copper, coal, gold, iron etc., with 37 billion tons of proven reserves and more than 57 billion tons of potential reservoirs. Iran is ranked among the 15 major mineral rich countries (1). In accordance with the statistics published by Statistical Center of Iran (SCI), there were 5.316 active mines and 84.922 employees in the whole country in 2012-13 (2) and according to the statistics published by Central Bank of Iran (CBI) in 2011 the share of this sector in the Gross Domestic Product (GDP) of the country was 1.2 per cent (3). Sangan Iron Ore Mines (SIOM) The deposit of SIOM is one of the largest iron-ore deposits in Iran, also considered to be one of the Middle East’s richest deposits, which contains a total geological resource of 1.2 billion tons of mostly magnetite with a Fe grade ranging from 27 to 61%. It is located 300 km southeast from Mashhad, the capital of Khorasan-e-Razavi Province, and 18 km northeast of Sangan town, in Khaf County, at latitude N34°24’, longitude E60°16’ in the north-eastern Khorasan-e-Razavi Province, 30 km west of the Afghanistan border (4) (Figure 1). SIOM is owned by the Iranian Mines and Mining Industries Development & Renovation Organization (IMIDRO). IMIDRO intends to develop an open pit mine complex and supporting facilities in SIOM for the production of about 20 Mtpy of iron oxide concentrate and pellets in four developing phases (5)."

Jan 1, 2016

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper outlines a cutting-edge probabilistic resource modeling workflow tailored to the Round Mountain epithermal gold deposit. The primary goal is to craft a robust and modern simulation process that enables the quantification and comprehension of anticipated discrepancies during mining reconciliation, offering a more precise gauge of expected gold quantities compared to conventional estimation models.

Dec 1, 2023