Search Documents

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By Walter R. Lawrence

Newmont Gold Company, formerly Carlin Gold Mining Company, is a publicly owned corporation, 95% owned by Newmont Mining Corporation. Newmont Gold Company has operated gold recovery operations North of Carlin, Nevada, since 1965. Development of the Gold Quarry ore body, 19 kilometers south of the original mine, resulted in the decision to construct gold recovery and ancillary facilities in what is referred to as the Southern Area. Plant No. 2, located 11 kilometers North of Carlin, Nevada, was designed to treat 6350 tonnes per day of oxidized gold bearing ore assaying 2.5 grams per tonne of Au at an average recovery of 87%. Flowsheet development conducted by Newmont personnel resulted in the decision to construct a carbon-in-pulp recovery circuit preceded by two-stage grinding, Detailed engineering was done at Toronto by Bechtel of Canada beginning on January 1, 1984. Actual construction began on March 1, 1984, and was completed in June, 1985. First feed was run on June 22, 1985.

Jan 1, 1987

By R. Bhima Rao

Performing a magnetizing roast in a furnace or kiln is a well-established technology. However, the use of microwave heat for the magnetization of hematite in the beneficiation of ferruginous bauxite is a new approach. This paper reports on an investigation of this procedure, which is followed by comminution and magnetic separation. The results of this investigation indicate that a nonmagnetic product containing 80% A1203 and 2.5% Fe203 with a recovery of 80% can be made from a crude bauxite ore containing 55.9% A1203 and 5.6% Fe203. This product is suitable for refractory use. The mechanism is explained by the ability of the microwave radiation to heat specific points within the bauxite. These heat-specific points are at the location of iron minerals. In a reduced atmosphere, the microwaves promote faster conversion of the iron minerals to a magnetic phase, which improves the magnetic-separation process.

Jan 1, 1997

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By N. B. Prenn

Case Studies in Open Pit Design Using Whittle 4D will be discussing the following four examples: 1) Optimization of process plant design using Whittle 4D as a sizing tool. In this case, the home office and project team had different views of the size of the final project. The home office wanted to reduce the size of the project to reduce capital expenditure, while the project team suggested a larger project. Whittle 4D was used to determine Net Present Value and Internal Rate of Return using the Whittle scheduler (FDAN) to schedule many alternatives, and calculate the NPV and return for each alternative. 2) Comparison of pit optimization methods: Lerchs-Grossman vs floating cone. Many pits are developed based on floating cone economics. A comparison of methods in one large gold mine resulted in the stripping ratio of the pit being reduced by 10% in the Whittle 4D optimization as compared to the floating cone optimization. 3) Pit optimization to determine if a new mill is justified. A large heap leach gold and silver mine needed to determine if a new mill was justified. The planning and scheduling would take several man months if completed without pit optimization and scheduling software. Whittle 4D software proved to be very effective in providing optimized pits and a mine schedule in a short time frame. 4) Pit optimization to determine how to mine and size. Open pit optimization determined where the underground operation should start, and whether the material should be processed by milling or heap leaching. One of our clients asked for help in determining where the pit should end and a new underground operation start. We used Whittle 4D to help determine where the pit should end and where to go underground. In addition the operation needed to determine how to process the material.

Jan 1, 1996

By Alexander N. Winchell

"The wash ore area on the Mesabi iron range covers a regionof the iron bearing formation extending from Grand Rapids on the west to the Hibbing district, about forty miles eastward. Not all of the developed ore bodies are of wash structure; some are of such grades that they can be shipped direct as merchants able ore. It is safe to say, however, that 65 per cent of the ore is of a possible wash structure and of too high a silica content to be classified as merchantable ore. The increase in the number of washing plants completed each year on the western Mesabi shows that ,the product must be of a structure desirable for furnace operation. The following is a list of plants which were . in operation, under construction, or with plans completed, at the end of 1918:"

Jan 1, 1920

By Robert A. Jankowski, J. Harrison Daniel, Fred N. Kissell

Introduction Longwall coal mining in the US has steadily increased since its introduction in 1960. There are now 108 systems operating. (Sprouls, 1986). Advantages of longwall mining include higher productivity, improved safety, and greater coal recovery. Respirable dust, however, is one of the more serious obstacles to realizing the full potential of longwall mining. Early in 1980, the US Bureau of Mines (USBM) initiated extensive in-house and contract research to identify and evaluate effective methods of controlling respirable dust exposure of longwall face personnel (Niewiadomski, Jankowski, and Kissell, 1981). It was found that several control procedures must be combined to assure compliance, using control techniques appropriate to the dust source. These techniques can typically be grouped into the following categories: reduction of dust generation; dilution of dust; capture or knockdown of dust; and dust avoidance. Control techniques can be divided into basic and effective dust control techniques; additional necessary controls; and optional supplementary controls. This information should allow longwall mine operators to select control methods applicable to their particular operations and to develop a dust control plan that meets Federal dust standards. Basic and effective dust control techniques There are three basic dust control techniques (Taylor and Jankowski, 1982) that should be implemented on all longwall mining operations. • A passive barrier or external water spray system design that confines shearer generated dust near the face and away from the operators. • Large quantities of water through the sprays, particularly the drum sprays, to aid in dust knockdown and prevent dust becoming airborne. • A cutting sequence that allows the shearer operators to work primarily on the intake-air side of the lead cutting drum. Shearer clearer There are some poorly designed shearer-mounted spray systems with nozzles directed upwind at the cutting and loading zone of the intake-side drum. These actually carry dust away from the face and upstream of the drum. Where, it mixes with the clean intake air (Fig. la,) and is carried out into the walkway over the shearer operators. The Bureau developed a novel shearer spray system, called the shearer clearer. It takes advantage of the air-moving capabili-

Jan 10, 1986

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By Louis J. Czel

Although lithium was first discovered by Arfwedson in Sweden in 1817, it did not reach any significant status in commercial application until 1908 when Thomas A. Edison received a patent covering the use of lithium hydroxide in alkaline' storage batteries. Edison's achievement can be regarded as a major breakthrough in the development of the lithium industry. In the years prior to 1908 lithium salts had found only modest applications in the pharmaceutical and pyrotechnic fields. The next important milestone in the growth of this net industry occurred in Germany in 1918 when Metallgesellschaft at its metallurgical laboratory at Frankfort-on-Main discovered that the addition of a few hundredths percent of lithium metal to aluminum and its alloys increased-the hardness. This brought into being a new commercial use of lithium in the manufacture of bearing metals. The new material, called "Bahnmetall" (railroad, metal), was widely used for, many years in the manufacture of bearings for railroad and automotive purposes. Its use continued until the early 1930's and there was a short-lived renewal of its production during World War II. Subsequent use of-the alloy was soon outmoded.

Jan 1, 1961

By Ronald I. Fuller

Core Laboratories, a division of Western Atlas International, maintains laboratories in all energy-producing areas of the United States, as well as in many foreign countries. Central to laboratory operations has been the incorporation of computers and computer software. Core has developed a mu1tiuser Laboratory Information Management System (LIMS) , which is currently installed in numerous company sites in the U.S., and is now undergoing installation in Canada. In addition, Core has provided custom soft ware to contract laboratories which Core operates on behalf of mining firms. The software development was done under the direction of the author in Denver, Colorado, and Casper, Wyoming. The intent of this paper is to pass some of the practical experience gained by our efforts on to those who wish to utilize computers more fully in the laboratory setting. The product of analytical laboratories is numbers. Nothing else comes from our work. We deal in information about samples. It is then reasonable to assume that the computer would be central to a laboratory operation. The hard part is to initially define what kind of computer the lab operation needs. The choices today can be very complex, and almost every hardware salesman is full of bad advice. Even the people in your own information services department may hold divided opinions. Since the advent of the personal computer, we have lived with a polarized data processing community. The PC boys consider their machines equal to any challenge, while the "save the mainframe" crowd view the PCs as limited toys that are only good for the things that clutter up a real computer. Management tends to lean toward whatever costs the least.

Jan 1, 1989

This paper provides a summary on the use of the POL YCOM high pressure grinding roll (HPGR) for increasing extraction in copper leaching. The energy-efficiency and significant hydrometa1lurgical benefits of the HPGR result in better acid-curing, higher solution application rates, improved copper extraction from various copper minerals and better recovery from high acid consuming ores. The HPGR's metallurgical features such as micro-fracturing, better liberation of disseminated and veinlet copper, increased oxygen and lixiviant penetration lead to higher copper extractions than achieved by conventional crushing. Flowsheet options, operational characteristics and applications for various copper ores are outlined.

Jan 1, 1996

By Rick Bearce, Minsu Cha, Mike Mooney, Yuanli Wu, Lisa Mori

"Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. Chamber pressures can reach 3-5 bar yet the vast majority of testing is performed under atmospheric conditions. This paper illustrates how pressure influences foam stability and conditioned soil behavior, and how atmospheric test results must be viewed in the context of expected chamber pressures. Torsional shear strength, compressibility and abrasivity of foam conditioned sand were found to be ideal when the void ratio was above the ASTM-determined maximum void ratio, achieved by sufficiently expanding the soil grain structure with foam, herein when the foam injection ratio at pressure exceeded 45%. Otherwise, the engineering properties of foam conditioned sand were not ideal, i.e., appreciable torque and abrasivity, low compressibility. INTRODUCTION Proper soil conditioning is critical for effective earth pressure balance (EPB) TBM tunneling. The formation soil at the cutterhead must be transformed into a highly compressible, low shear strength and low permeability medium within the excavation chamber to allow effective EPB performance. This behavior must be maintained for a certain residency time while the soil is in the chamber and screw conveyor. The vast majority of published studies on conditioned soil behavior have been performed under atmospheric conditions (Quebaud et al., 1998; Bezuijen et al., 1999; Psomas and Houlsby, 2002; Vinai et al. 2008; Thewes et al., 2012; Peila, 2014); however, the desired soil behavior must occur under chamber pressures that can reach 5-7 bar. The influence of pressure on conditioned soil is significant and is dramatically different than behavior under atmospheric pressure (Williamson et al., 1999; Mori et al., 2015). This paper illustrates how pressure influences conditioned soil behavior and how atmospheric test results must be viewed in the context of expected chamber pressures. The influence of pressure on foam bubble size (including with time) is shown through digital image analysis. The influence of pressure on foam half-life is also investigated. The compressibility, shear strength, and abrasivity of conditioned soil under pressure is presented and explained in terms of density, soil and air compressibility and porosity."

Jan 1, 2016

By M. Portal, L. Goicochea

This study is carried out in the Zenit mining concession, which is located in the city of San Pablo in the department of Cajamarca in Peru. The Project has 33 mineralized structures and according to laboratory analyzes we have the presence of gold and silver. The geostatistical evaluation provides an analysis on the distribution of precious metals in the vein. This information is used to improve the efficiency of metal extraction and to reduce costs. The general objective is to evaluate the polymetallic veins (Au and Ag), for which the classification of resources (measured, indicated, and inferred) has been carried out, taking into account the parameters of minimum distance from the composite, corresponding volume and tonnage calculation. In addition, an inventory of estimated geological resources was carried out with the block grades obtained to generate the tonnage-grade curves.

Feb 1, 2024

By T. E. Masoner

The struggle to get the minerals industry seriously interested in high intensity wet magnetic separation* has been difficult. The high capital cost of the equipment, the lack of basic research, the lack of operating information, and the diverse characteristics associated with different minerals and ores have prevented the development and use of HIMS-W on a wide scale. The Climax Molybdenum Company, a Division of American Metal Climax, Inc., located at Climax, Colorado, was among the first companies in the Americas in recent years to support the development of HIMS-W to recover weakly magnetic minerals on a large scale. The Climax Molybdenum Company, one of the world's largest underground mines, processes about 40,000 tons per day of ore, from which about fifty million pounds of molybdenum disulfide are produced each year. By-products include tungsten, iron pyrite, tin, and some monazite.

Jan 1, 1968

By R. M. Smailer

Detailed description of the development of the FIOR process1 and, subsequently, other technical papers relating to the operation and start up of the FIOR plant2,3 are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Company during the 1950's and 1960's; and the facility in Venezuela was designed and constructed by Davy McKee with the plant start up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of the ownership being private capital.

Jan 1, 1981

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By M. H. Basiri

Crude oil, as a central commercial commodity, is tied to major economic activities in all nations. Also its price fluctuation plays a significant role in global political and economic situation, as a change in the price invariably affects the cost of other goods and services. Therefore reliable forecasts of the price of oil are interest for a wide range of applications. Several approaches have been proposed over the past few years. These may divide into three categories; artificial intelligent, statistical techniques and hybrid methods. The neuro-fuzzy is one of the sub divisions of hybrid method, containing neural network and fuzzy techniques. In this paper a novel forecasting model based on adaptive neuro-fuzzy inference (ANFIS) is proposed to predict monthly crude oil price. To be able to train and test the model, the statistical data from 1990 to 2010, was obtained from West Texas Intermediate oil prices. The results are compared with a multi criteria regression analysis, it is demonstrated that the neuro-fuzzy lead an accurate and more promising forecast.

Jan 1, 2012

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997