Search Documents

By H. Maleki

Roof falls continue to affect productivity and safety in U.S. coal mines in spite of significant increases in support utilization in recent decades. To minimize roof stability problems while controlling support effectiveness, the U.S. Bureau of Mines is conducting research on support and ground monitoring techniques. Practical implementation of this research is presented in this paper. Instruments to monitor rock mass deformation, support loads, and microseismic emissions have traditionally been used to assess roof stability. Controlled-source seismic surveys are being used as well. In this paper, measurement techniques are reviewed, and the effectiveness of deformation measurements is demonstrated. This is achieved by an analysis of deformation history from four case studies in room-and-pillar retreat mines. In spite of differences in geologic, geometric, and support conditions in these mines, roof behavior is shown to have been similar prior to failure. The rate of roof movement is suggested as a reliable indicator of roof stability.

Jan 1, 1993

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By T. L. Owen

Since 1993 Cyprus Amax has brought $2.5 billion dollars of greenfield and expansion projects into production, taking it from a mid-sized domestic minerals company into a major international minerals organization. The near simultaneous development of these multiple mineral projects in different locations around the world provided the opportunity for Cyprus Amax to develop a formal project management approach based, in large part, on an outsourcing philosophy. This formal project management system along with its outsourcing philosophy has served the growth agenda of Cyprus Amax extremely well. These preceding factors, coupled with the in-house retention of a core project group that fully understands the breadth of skills and abilities needed to undertake development of multiple large projects successfully, have been the cornerstone of Cyprus Amax’s project development success.

Jan 1, 2000

By James Y. Oldshue, Paul M. Kubera

Most coillillercial processing applications employing mixers in various types of slurry systems are continuous flow. These applications may also be multiple stage, with the stage number varying anywhere from two or three to ten or more. Two questions that usually come up at the beginning of any proposed pilot plant study are (1) can the pilot plant unit be operated batch-wise, and the results extrapolated both on the basis of scale and fluid motion to the full-scale tank which will be continuous-flow (and probably multi-stage), or (2) does the pilot plant need to be operated in a continuous-flow fashion, and if so, does the exact number of tanks/stages that are proposed for the plant need to be used in the pilot plant? We will consider these possibilities in sequence and present the principles involved in running some of the various pilot-plant arrangements.

Jan 1, 1992

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By A. J. Naldrett

Over the past six or seven years important new ideas have been developed concerning the origin of nickel sulfide deposits. To a large extent these have been stimulated by the major nickel discoveries of the Eastern Goldfields area of Western Australia (Woodall and Travis, 1969; Ewers and Hudson, 1972). Prior to these finds, the most important nickel camps were regarded as being associated exclusively with intrusive rocks such as the Nickel Irruptive at Sudbury or the intrusive peridotites at Thompson, rocks that were thought to have no close association with volcanism. Study of the Australian discoveries, coupled with work in South Africa (Viljoen and Viljoen, 1969) and Canada (Naldrett and Mason, 1968; Pyke, Naldrett and Eckstrand, 1973), has shown that volcanic rocks with true ultramafic compositions and extrusion temperatures of 1400 to 1600°C were a common feature during the Archean. Under certain circumstances economic concentrations of nickel sulfides have formed from these rocks, either settling to the base of their associated flows or accumulating in shallow intrusive feeders to the flows. The aim of this article is to show how these ultramafic rocks can be recognized, how the nickel deposits, if present, are likely to occur within them, and what special features characterize ore-bearing examples of the rocks.

Jan 1, 1975

Interstate 70 running into the mountains west of Denver, CO is the main access to the state?s numerous ski areas and other tourist attractions. As such, the highway is a vital part of Colorado?s economy. Due to the mountainous terrain in which it winds, I-70 is limited to two lanes in either direction. And, during the past few decades, the volume of traffic has increased to the point where motorists encounter major delays, particularly on Friday evenings and Saturday mornings heading west from Denver, and then again on Sunday evenings heading east. In the past, those delays occurred mostly during the ski season. However, many of the mountain towns have been successful in turning their resorts into year-round vacation destinations. A good move economically, but the pressure added to I-70 has caused even greater traffic delays, sometimes to the point where some Front Range residents avoid trips to the mountains.

Jan 1, 2013

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By Harry M. Conger

Kaiser Steel Corporation's Eagle Mountain Mine is located in the Colorado Desert, 60 miles east of Indio, California. Concentrates from the mine are shipped by rail 164 miles to the company's steel mill at Fontana, and also to Longbeach, California for export. Temperatures are typical of the lower desert ranging from a high of 120 degrees in the summer to a low of 25 degrees in the winter. The average annual rainfall of about two inches comes mainly as cloud bursts during the summer months. From its inception, the Eagle Mountain Mine has had the problem of breaking its mine rock. Practices followed from 1949 until 1962 were very costly, did not produce uniformly good fragmentation, and were incapable of sustaining high production. During this period, every conventional type of explosive then in use was tried and found to be unsatisfactory for one reason or another. The first slurry test work at Eagle Mountain was started in 195E and finally by 1962, after having tried all the slurry mixtures then available including some "home made" formulas, a metallized slurry was perfected at the mine which overcame all of the disadvantages of former blasting methods.

Jan 1, 1965

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Fred C. Wrobbel

Two counties in Illinois, Ope and Hardin, and three counties in Kentucky, Crittenden, Livingston and Caldwell comprise the entire Kentucky-Illinois fluorspar district. The output from these five counties, however, makes up over 60 percent of our domestic fluorspar production, amounting to some 175,000 tons of finished product in 1956, The area is rough and hilly. It is bisected by the Ohio River, and has numerous smaller rivers and creeks. Add to this a generous average annual rainfall, in excess of forty inches, and it is understandable that the-area-can boast of an ample water supply. An abundance of water, however, is unfortunately not always conducive to ideal mining conditions. The faulted structure of the area and the soluble Mississippian limestones make the subsurface sediments' willing hosts to the surface water. Limestone cavers and sinkhole topography also compound the occurrence of underground water. It is little wonder, then, that water frequently presents an economic problem in the area, particularly in vein-type mining.

Jan 1, 1958

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By John A. Wolfe

The concepts of sea floor spreading and plate tectonics provide more logical explanations of some geologic processes than were possible a few years ago. I plan to premise my discussion of the regional features of Philippine porphyry copper deposits on this tectonic basis, recognizing that parts of the picture can be explained in other ways, but in the belief that this is the best explanation of the whole. The sequence of events which results in the formation of Porphyry deposits (Figure 1) can be summarized as the result of collision of crustal plates, subduction of the oceanic plate, emplacement of a serpentine ultrabasic diapir, formation of a dioritic magma at depths of 300 to 500 km, rise of the magma to a sub crustal or intra-crustal chamber, eruption of andesitic volcanoes, emplacement of diorite or differentiation of the magma into more acidic products, multiple intrusion of hypabyssal rocks and hydro-

Jan 1, 1973

By S. K. Kawatra, V. Claremboux, S. Valluri

Carbon dioxide capture from coal-fired power plant flue gas and subsequent sequestration is expected to play a vital role in mitigating global climate change. To meet the growing need for CO2 capture Technology, Michigan Technological University is researching CO2 capture and Utilization. We have successfully converted CO2 into oxalic acid using an electrochemical approach. If oxalic acid can be produced in bulk from CO2, it can be used to leach rare earth minerals at low cost. Electrochemical reduction of CO2 to hydrocarbons and other chemicals is a complex multistep reaction with adsorbed intermediates. The exact reaction mechanisms leading to various products are not clear from the literature to date and will likely change over the range of conditions like pH, electrode potential, electrolyte medium, catalyst, etc. In this paper, we will present an idea of how the factors mentioned above will effect the electrochemical reduction of CO2 to Oxalic acid. INTRODUCTION. CO2 is thermodynamically quite stable, as shown by its highly negative heat of formation. Thus, it is expected that the formation of any useful chemical from CO2 will require the input of at least as much energy as geological sequestration. However, to be more effective the resulting economic value of the chemical need only pass the cost of the additional energy required beyond geological sequestration. This lends itself to two extremes: one where the quantity of energy required is low and one where the economic value of the additional energy is low. It is expected that CO2 can be reduced via electrolysis to several compounds. Of particular interest are formic acid, oxalic acid, methanol, ethanol, formaldehyde, and carbon monoxide (as a component to syn-gas). These chemicals have been reported as electrolytic products previously in literature and have considerable potential for application. EXPERIMENTAL Electrocatalytic Production of Oxalate from CO2 We are using membrane electrolysis cell to produce oxalate from CO2. A membrane electrolysis cell is a 2-chamber electrolysis cell where the chambers are separated by a selectively permeable membrane. To produce oxalate, a cation exchange membrane (which selectively exchanges cations) was used. Previous literature suggests that in the cathode chamber an organic electrolyte, such as tetraethylammonium perchlorate or tetraethylammonium bromide in dimethylformamide, are preferred3. In the anode chamber, a sodium hydroxide solution water is used. Carbon dioxide is then bubbled into the cathode chamber as a current is applied.

Jan 1, 2019

By S. Y. B. Subbarao, K. Ravindranath

Lead and Zinc concentrates are being recovered at Rajpura- Dariba (Distt. Rajsamand, Rajasthan, India) from a complex multi metal sulphide deposit since 1984 by selective flotation employing a large number of reagents. The cost of concentrates' production has been high. Due to the increased availability of concentrates world over and to be competitive, it is necessary to reduce cost of production. An effort has been made by the R.D. Department of Hindustan Zinc Limited to bring down the cost by resorting to production of Bulk Pb + Zn concentrate with enough Ag to make it attractive to the smelters. This paper gives an account of open cycle testing and locked cycle testing in the Dowa Continous Mini Flotation unit. The metallurgical data generated in the mini flotation unit indicate the possibility of obtaining smelter-acceptable bulk concentrates containing Pb+Zn 45%, Ag 400 ppm and graphite carbon about 3%. An in-plant trial in the 3000 TPD concentrator indicated that there would be savings through dispensing with and reduction in some reagents, lower power requirement, etc. Also, a substantial increase in revenue is expected due to higher recoveries by resorting to bulk concentrate production as against individual concentrates.

Jan 1, 1995

By Franklin J. Stermole

The current financial state of the mineral industry, in general, is bad. Economic prospects for improvements in the near future are uncertain. What will improve mineral investment economics so the mining industry can return to a more normal (in terms of past experience) production level? Basically, mineral commodity prices must rise. They must rise to economically justify reopening closed mines and for management to seriously consider expansion or development of existing and new mines. With the worldwide economy depressed for more than a year now (longer for most segments of the mineral industry), supply/demand relationships for mineral commodities are such that prices are depressed-except for precious metals. In investment analysis of the economic potential of existing or new investments in any industry, product price generally is one of the key parameters having great impact on the economic viability of projects. Petroleum and synfuels industry development contracted last year for the same product price reasons that have brought mineral industry development to a standstill. Much of the new mine development activity now underway or in the serious planning stages around the world involves precious metals ore body development simply because precious metal prices are high enough now or are projected to be high enough in future production years to give overall satisfactory project economics. It will take significant improvement in nonprecious metal mineral commodity prices in 1983 to develop significant new mine investment interest except in very high grade ore body special situations. Mineral Investment Decision Making Before progressing further with the discussion of mineral investment considerations for the coming year, it should be emphasized that mineral investment decision making-like all industry or individual investment decision making does not relate just to economic considerations. Investment decision making should and generally does involve three analyses: • Economic analysis • Financial analysis • Intangible analysis Economic analysis evaluates the relative economic merits of investment situations from a profitability viewpoint based on discounted cash flow analysis of projected investment revenues and costs. Financial analysis, on the other hand, refers to where and how the funds for proposed investments will be obtained. Regardless of the project's economic potential, if you can't finance it, the project will not be done. Intangible analysis considers factors affecting investments but which cannot be quantified easily in economic terms. Typical intangible factors are legal considerations, public opinion, goodwill, environmental and ecological impacts, and regulatory or political considerations, to name a few. New mine development investment decision making in the US has been impacted heavily by intangible considerations in the past decade and will probably continue to be impacted by them in 1983. There is a common tendency in literature and management practice to interchange the terms economic analysis and financial analysis. This often leads to confusion about the rationale for investment decisions. For example, in the past year a majority of companies in all types of industries cut back budgets for new projects. Often this was done not because new project economics were unsatisfactory, but because cash flow from existing operations was reduced compared to previous years due to the recession, and debt service requirements were high from existing loans so new borrowing was undesirable. For financial reasons, in other words, many projects were shelved last year. That included some precious metal mining projects and many petroleum projects. Many other projects were shelved for economic reasons (sometimes combined with financial reasons in the case of marginal economic projects). New mine development for copper, lead, zinc, molybdenum, iron ore, and synthetic fuels are a few examples. Economic Uncertainty and Financial Considerations Mineral project analysis has always involved a lot of uncertainty with respect to determining ore grades, tonnage of producible reserves, operating and capital cost projects, and mineral commodity prices estimates. The wide swings in mineral commodity prices in recent years and the almost impossible task of projecting future prices with any degree of confidence or accuracy concerns mineral project investment decision makers. In developing a new copper or silver mine, it is not today's price of copper or silver that is relevant to economic analysis of the mine, but what the price will be during the producing years. There is no way to avoid projecting the escalation (or de-escalation) effects on revenues and costs. To analyze a project in terms of today's dollar revenues and costs implicitly assumes that escalation will not change today's project costs and revenues; or that, if they do change, the project economics will be unaffected by the changes. This often is not the best or even a realistic assumption. The inherent uncertainty associated with historical mineral price swings is exacerbated in 1983 by the uncertainty of when

Jan 2, 1983