Search Documents

By E. J. Duggan

In the course of the grinding experiments conducted at Climax over the past twenty years one interesting phenomenon was discovered. This was that balls made of certain types of steel grind more ore than some others. The most significant variation was found in the results secured with a hard alloyed forged bail compared with the forged carbon ball supplied by most ball manufacturers These findings were confirmed in many repeated controlled tests. The value of these tests depends on the methods used, the facilities available and the care with which the investigations were conducted. These are described in the following. This testing has largely been done in eight 91 x 81 low discharge ball mills in closed circuit with 7811 duplex screw classifiers. The mills run at 20 RPM on a feed approximately minus 3/8 inch. The ore is ground through 28 - 35 mesh in one stage. Each mill and auxiliary classifier is in a separate, parallel grinding and flotation section The, ore to each: section is the same in every particular and is fed to each mill bin from a common conveyor tripper. The ore from the bin to the ball mill is weighed on a conveyor scale. The power input to each mill motor is determined with a watt hour meter which measures the power to the mill motor only. Both the scales and meters are checked periodically by standard methods and have been found to give consistent readings. Automatic samplers are employed on each section to obtain accurate measurement of the size reduction. A size analysis of the classifier overflow is made each shift and a composite size analysis is obtained from a weighted average of the various shift analyses. The mills are driven by 450 horsepower synchronous motors so that there is no speed variation and shell liner age is kept as nearly the same as possible in mills under test. The same set of operators is assigned to a mill under test as to the control mill. In all other particulars such as ball load, mill density, liner design, etc., the mills are operated in precisely the same manner. This is an ideal arrangement for plant testing. From observations of ball mill performance over the past twenty years, it is the opinion of the operating staff that variations of as little as one to two percent in mill capacities may be determined if sufficient operating hours are devoted, to a test. Relations between mill capacities, fineness of grinds and power consumptions have been established with a high degree of accuracy. In Table I are given the figures for one test. These show that while the grind with the hard ball was slightly coarser, the tons ground per hour was 5.4 percent greater with the soft ball, and 6.1 percent greater on the basis of minus 100 mesh produced. The power consumed per ton with the hard ball was 4.4 percent greater on a tons per hour basis. The soft ball was inferior in wearing qualities and steel consumption per ton of ore was 24 percent greater with it. In this test the mills were charged with the two different balls for a period of three months to allow the ball loads to come to equilibrium. In Table II are given the specifications of the two balls. The difference in grinding rates may be accounted for by the nature of the ball surfaces. The surfaces of the soft balls after being worn a while are rougher to the touch. Enlarged photographs of the worn-in surfaces of hard and soft balls are shown in Figure I. These show the presence of scratches or skid marks on the hard ball surface which indicates less nipping effect. The Climax ore pulp has a pH of 6.0 and is in a dispersed state. The viscosity is low compared with most ores especially those that are conditioned with lime. This would lower the tendency of the pulp to adhere to the balls with a lower grinding efficiency as a result. It was also thought that the relative rates of wear from surface to center might affect the make-up of an equilibrium ball charge. This probably has little effect on capacity as shown by the size analyses of the two ball charges in Table III. This hypothesis was subsequently investigated by the use of rationed charges. The rationed charge did not overcome the advantage in

Jan 1, 1958

By Fred C. Bond

The perennial subject of comminution is deserving of a fresh approach if one can be found. This is attempted here by directing attention primarily to principles rather than to theories. While theories attempt to explain how a certain process acts, principles delineate the laws which the action-must follow. Comminution may be defined as the progressive separation of particulate matter. At the present time this is accomplished commercially by applying energy in the form of compressive and, shearing forces. Such forces strain and distort the particles they contact. When-the applied stress locally exceeds the breaking strength at the weakest flaw in the particle, a crack tip forms. The surrounding strain energy flows to the crack tip, which rapidly extends through the particle as a break. The minute changes in shape and the resulting energy flow cause the failure of other highly stressed flaws, with the consequent formation of a progeny (1) of new smaller particles out of its destroyed progenitor. The applied mechanical energy is transformed into strain energy as the particle is distorted, and then into heat when it fails. Only a tiny fraction of the order of 1/1000 of the applied energy necessary for breakage appears as new surface energy in the product particles. The comminution problem is the relationship between, energy input and product particle size. Its solution is of great-economic importance,

Jan 1, 1961

By Robert A. Haney, David J. Atchison, Kenneth G. Fields

Mining systems with greater than a 20-foot face advance (deep cut) have become popular due to their increased productivity and safety. The face dust collection system used in many of the mines employing the deep cut systems, incorporates a machine mounted dust collector with either a blowing or exhausting line brattice and a remote control operated continuous miner. In order to characterize and quantify the parameters used to control dust with these systems, the Dust Division conducted studies on four mining sections using continuous miners with deep cut mining systems. On each section, the dust control system incorporated line brattice with a machine mounted dust collector. The remote control made it possible for the continuous mining machine to advance further while permitting the operator to remain under supported roof and away from dust generated during mining. The purpose of these studies was to evaluate the effectiveness of deep cut mining systems using dust collectors to control respirable dust exposure. This paper summarizes the results of the studies conducted. At each mine face workers were sampled to determine their full-shift dust exposure. Additionally, fixed point dust samples were collected at various locations to determine relative concentrations of dust generated from mining. Air quantities were measured at each working place to determine the amount of air delivered to the face area. Evaluations were made by comparing worker exposures to respirable dust samples taken at appropriate locations upstream and downstream of the coal faced being mined. An estimate of the amount of the respirable dust being generated at the face during mining and the amount of respirable dust being removed by the dust collectors was made by balancing the air quantities and the dust concentrations immediately upstream and downstream of the coal face. Results of the studies showed that the dust control systems, were effective for controlling workers exposure to respirable dust. Dust collector efficiencies were determined to be approximately 85 percent. While the dust collectors were effective in removing respirable dust, the success of the systems with line brattice greater than twenty feet from the face, was dependent on the use of the remote control which permitted the continuous miner operator to remain out of the high concentration dust cloud in the working face. Dilution from intake air, combined with the dust collector efficiency, maintained exposure of other section workers below applicable standards.

Jan 1, 1991

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By Samir Kumar Pal, Rajasekar Rathanasamy, Gobinath Velu Kaliyannan, Moganapriya Chinnasamy, Sathish Kumar Palaniappan

The research examines the performance of uncoated and coated tungsten carbide-cobalt rock cutting bits. It aims to optimize process variables (cutting speed, depth, coating material) considering multiple output responses (cutting forces, specific energy, wear rate, material removed, angle of reaction forces). The study uses a hybrid optimization technique combining Taguchi design, grey relational analysis, and fuzzy logic. The optimal parameter combination was found to be cutting speed: 200 mm/s, cutting depth: 6 mm, and titanium aluminum silicon nitride coating.

Apr 24, 2022

By Erle I. Shobert

In the comparison and consideration of synthetic and natural materials, graphites represent a situation in which natural graphites amount to less than 10% of the total carbon and graphite production by weight, and less than 5% in dollar volume, There are few applications where it could not be re- placed by synthetic graphite. On the contrary, synthetic graphite materials can be engineered to cover an extremely wide range of applications. These include electrographite brushes for rotating machinery, pyrolytic graphite, graphite-impervious pipe, nuclear moderators, high purity spectrographic graphite, power tube anodes, graphite rotary shaft seals, and rocket nozzles. The special qualities of natural graphite and its limitations are delineated and the almost unlimited possibilities in artificial graphite materials are discussed.

Jan 1, 1964

By T. G. Hayes

Economic and environmental regulations in the coal industry have required companies to evaluate their current blasting method of loosening in-situ coal. This paper will review ripping vs. blasting thick in-situ coal seams, handling frozen active coal stockpiles and proper stockpile conditioning and reclaiming. How basic operating technique can improve job efficiency, productivity and cost per ton.

Jan 1, 1995

By SANJIT KUMAR PAL, Sarvesh Kumar, Arindam Guha

The integrated geophysical study around pipe 1 and pipe 2 in Wjarakarur Kimberlite Field (WKF) assisted in comprehending the response of pipes. In the present study, we have attempted a combined analysis of very low-frequency electromagnetic (VLF-EM), electrical resistivity tomography (ERT), and magnetic methods to analyze the response from pipe 1 and pipe 2. A comparative analysis along all the profiles revealed the extension, depth, and geometry of the pipes. The results of VLF data and ERT data have been compared for two profiles of pipe 1 and pipe 2. Fraser-filtered grid map generated from all profiles of pipe 1 proficiently demarcated the trend of kimberlite pipe extension with high Fraser filter value associated with kimberlite. The ground-based magnetic data around pipe 1, pipe 2, and pipe 6 have been processed to analyze the magnetic behavior and subsurface structure based on the susceptibility contrasts. Analytical signal (AS) map revealed the extension of pipes, which was validated with the Fraser-filtered grid map. Analytical signal anomaly pattern reveals that pipe 1, pipe 2, and pipe 6 are trending in SW-NE, NE-SW, and NE-SW, respectively. Based on this study, the results indicate the conducting nature of pipe 1, whereas pipe 2 is resistive in nature. Further, the Euler deconvolution technique has been applied to calculate the possible depth of pipes from magnetic data. The comparisons of calculated depth ranges obtained from all geophysical techniques correlate well and validate the result (Table 1). The geological borehole data at pipe 1 and pipe 2 reported by the Geological Survey of India are well corroborated with our combined geophysical study.

Jan 17, 2024

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By B. Culkin

The production of fine particle products within the mineral processing industry is a very important market segment. Many of these products are processed in an aqueous state and must ultimately be dewatered. This entails processes which are very energy and capital intensive. The introduction of membrane based dewatering systems has offered great promise in the area of energy saving and operating costs. Unfortunately, membrane separators have not yet had the ability to handle high solids. New Logic introduces a system which can concentrate a low solids stream to a high solids sludge in a one pass, very energy efficient system.

Jan 1, 1993

By Paul Lenchuk

The concrete block industry can trace its beginnings to the early 18th century when most of the experimental work was being carried out in England. In America, the concrete masonry industry got started shortly after the Civil War and has had sometimes a spectacular, but always a steady growth since then. From a few hundred thousand concrete masonry units made in the late 19th century, the industry today produces approximately 3.3 billion concrete masonry units making it the largest industry in the United States for masonry wall materials. There were 3500 concrete masonry plants manufacturing these units after World War II. This nwnber decreased to 1500 by 1970 although the production of concrete masonry units increased by over 100% in the last 25 years. One of the reasons for this increase in production by less than half of the plants which once existed, is the tremendous strides made in automation of production machinery. The concrete masonry plant of today is probably one of the most automated small businesses in existence. Within a few years it will be possible to push a button and the entire manufacturing process will begin with no human hands touching the units until they are laid up in a wall at the manufacturing plant and are trans-ported to the job site. No other concrete product has reached this state of manufacturing sophistication and it is one of the reasons why the price of a concrete masonry unit is not much different than it was 2S years ago. Because of automation, it is safe to say that concrete masonry will remain a highly competitive building material for many years to come. The problems that beset the continued use of this material are not related to the cost of manufacturing and delivering the product. What are some of the problems as well as some of the opportunities and is the golden age of opportunity knocking rather than a wolf in disguise? The use of concrete masonry has grown each year because a larger unit was provided at less cost than other competitive materials. Concrete masonry has had severe competition from the clay products industry as well as masons who laid the product in the wall and who resisted concrete masonry for many years. Even today

Jan 1, 1971

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Jim V. Rouse

Adverse water-quality impacts of uranium mining and milling activities on both surface- and ground-water resources in the Grants Mineral Belt have recently been documented.1 In some cases, the impacts resulted in violation of existing regulations and license conditions and have endangered public health. Unfortunately, industry-sponsored ground-water monitoring programs do not adequately record the actual impacts of mining and milling on ground-water quality.

Jan 1, 1976

By Leonard Bronitsky

The construction mineral aggregates industry--the largest industry on a tonnage basis--is threatened with large shortages in the near future. Ironically, these common minerals which include sand, gravel, and stone are among the most plentiful in the earth's crust. However, as these minerals are low in value and used in large volumes, they are extremely sensitive to transport cost, e.g., a haul of 20 miles doubled the delivered cost of mineral aggregates. Consequently, these minerals must be located close to points of demand to have economic usefulness. But the development of new deposits is virtually impossible near many urban areas for legal, sociological and economic reasons. The spector of unfinished urban transport systems, curtailed residential construction, and a general deterioration of the physical urban plant, looms as a direct consequent of future mineral aggregate shortages in the U. S. metropolitan areas. The shortages of mineral aggregates in the Greater New York Metropolitan Area (G.N.Y.M.A.) are prototypical of the shortages faced by the U. S. Metropolitan areas. This paper presents an economic analysis of the consequences of not considering the broad aspects of conservation economics as a major component of resource management. The needless annual cost for the G.N.Y.M.A. is shown to be $30 million.

Jan 1, 1974

The National Institute for Occupational Safety and Health (NIOSH) conducted field tests to evaluate the effectiveness of a wet head continuous mining machine for reducing dust exposure for continuous miner operators. Wet head technology delivers water via sprays to the continuous miner's cutter head as opposed to traditional standard sprays located on the boom and body of the mining machine. The sprays, positioned directly behind each bit on the cutter head, deliver water at the point of attack, serving to cool the bits during mining to reduce the potential for frictional ignitions. The sprays also flood the coal with water to potentially suppress dust generation. Dust surveys were conducted at several mines to evaluate the wet head's effectiveness to control respirable dust exposure at the continuous miner operator location and in the immediate return. Results show that the wet head miner improved air quality at both locations to varying degrees in some cases and not in others when compared to a continuous miner with a standard spray system.

Jan 1, 2010

Design models for belt conveyors used in mines predict both the belt power requirements and belt tensions. Conveyors with slightly downhill profiles are more complex to predict due to the way that models such as CEMA interpret friction. Performance of a particular conveyor in relation to other conveyors in the same system requires an analysis of natural stopping times, braked times and take-up location. A review of CEMA-based PC models is presented for design of underground multi-flight belt systems.

Jan 1, 1995

By L. W. Laage

Throughout recorded history, underground fires have plagued mining operations. Compared with other hazardous situations in underground mining, a fire can become a global problem by swiftly spreading deadly carbon monoxide and other products of combustion (POC's) throughout the whole mine, often without warning. Experience has shown that when fires are detected and located in their early stages, they are much easier to control and proper escape routes can be more intelligently selected. Recent advances in sensor and data communication technology have made reliable mine fire .detection system installations possible. Unlike building construction. in a mine, it is impractical to install detectors at every desired location. Abandoned workings and unsafe locations preclude sensor installations from both safety and economic standpoints. The net effect is that some fires are detected and located early while the location of others, even if detected early, remains unknown too long for effective evacuation and fire fighting.

Jan 1, 1989

By R. J. Sweigard

Stabilization of slopes on abandoned mine land (AML) invariably involves some channelization to control surface drainage. Typically, these channels are lined with riprap or gabions, depending on gradient and expected flow rate. The conventional treatments pose a problem since they require frequent maintenance and replacement at times. Soil bioengineering presents an alternative to the conventional measures. In soil bioengineering, living woody plant material forms the main structural component in systems designed to prevent shallow mass slope failures, surface erosion, and channel bank erosion. An experimental application of soil bioengineering techniques was designed and implemented at an AML site in eastern Kentucky. The design consisted of live fascines and live stakes using willow branches installed with coir geotextile. Channel gradient, length, and cross-section were considered in the design.

Jan 1, 1998

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980