Search Documents

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By John R. Gaines

I am not a member of AIME, and this is my first annual meeting. As a lifelong member of the non-ferrous metals industry I have enjoyed listening today to speakers point with pride and view with alarm the public relations activity or lack thereof in the halls of government, as well as at the grass roots. There is much to be alarmed about, to be sure, but also some accomplish¬ments to be viewed with pride. Other speakers have given a broad overview of our industry's relations with their several publics. I will be specific about two incidents in which The Anaconda Company faced the loss of confidence of a large portion of its publics: the nationalization of our properties in Chile in 1971 and the closing of our under¬ground mines in Butte, which was announced last October. If I have a minute left over, I will speak about our concern for the loss of confidence in business institutions which has been re¬vealed in recent public opinion polls.

Jan 1, 1975

By Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more 'coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes de signated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the La-mella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1977

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By Steven J. Stokowski, Frederick M. Bodycomb

This chapter deals with the use of industrial minerals in insulating materials used to control our thermal and acoustical environment. There are numerous products on the market used for thermal and acoustical insulation; they consume substantial quantities of a variety of industrial minerals. Following is a brief review of the theory and function of insulating materials. Acoustics is the science of sound, and architectural acoustics deals with sound in buildings. If this definition is broadened to include transportation vehicles, it is this end use for which acoustical insulations are primarily manufactured. Sound is defined as the auditory sensation in the ear, or the disturbance in a medium which causes this sensation. Acoustical insulation is used to reduce or eliminate noise, defined as unwanted sound. Noise control may be accomplished by the reduction of sound radiation at the source, by utilizing sound reducing construction methods such as staggered studs, etc., to control sound transmission, or by using sound absorbing material on walls, ceilings, and floors (Rossing, 1985). Acoustical insulation functions by absorbing the energy in sound waves in a porous material. As the sound waves penetrate the pores, they are dissipated by reducing the amplitude of vibration of the air molecules by contact with the pore walls, with subsequent conversion of the sound energy to heat energy. Acoustical insulation is generally highly porous, 1.3 cm or greater in thickness, and has interconnected pores. Acoustical insulating materials include fibrous vegetable or mineral matter and cellular organic and inorganic material, such as natural or manufactured foams (Sabine and Moulder, 1979). Acoustical materials are most commonly porous boards and tiles, which are often composite materials with perforated facing. Roof insulation board and lightweight concrete can also contribute to the absorption of noise. Thermal insulation is defined as material used to control the flow of heat. It may be used for heat control from low cryogenic temperatures (below -100°C) to in excess of 2 200°C for applications such as ablative shields for spacecraft. Heat transfer occurs by conduction, convection, or radiation. Conduction is the transfer of heat without the movement of the conducting medium, as through a metal. Heat convection through a liquid or gas takes place by movement of the medium. Forced convection is the basis for heating and cooling equipment, utilizing pumps or blowers to transfer the thermally conditioned fluid. Free or natural convection occurs due to density differences in the fluid. Radiation is the transfer of energy in space (Eckert, 1985). Conduction of heat through a solid is reduced by insulating the body with foams, or fibrous or small celled granular material. Heat transfer through a gas (convection) is controlled by creating many small pores which inhibit the movement of the fluid, substituting a gas of low thermal conductivity, or evacuating the space. Heat radiation can be reduced by the use of materials that reflect or absorb the energy (Glaser, 1967). Thermal insulating materials may be vegetable or mineral fibers, organic or inorganic particles, or foams with small pores, generally used to form a low density thermal barrier. They may be blocks, poured lightweight cementitious materials, bricks, etc.

Jan 1, 1994

By Edward C. Dowling

Cleveland Cliffs and affiliated companies have established a commitment to the development and use of integrated process control. Substantial capital investments in process control, coupled with the dedication of human resources to effectively use the information, have generated meaningful business results. Improvements in productivity, operating costs and product quality have been realized. This paper presents an overall process control and information strategy, specific case studies, lessons learned and the current view of the next steps in the continued journey toward integrated process control and information management.

Jan 1, 2000

By E. B. Jensen

The results of an extensive one- year test period of a nonelectric explosives detonating system led to the mine-wide adoption of this system at the Henderson Mine in early 1978. Since that time, extensive experience with nonelectric initiation has verified the earlier results which include the following benefits: 1. Increased blasting safety 2. Improved productivity 3. Cost effectiveness 4. High reliability At the present time, while electric blasting caps still experience a limited use restricted to trunkline initiation, all heading rounds as well as the longhole bell, undercut, boundary cutoff and raise blasting are detonated non-electrically. The primary blasting agent used is AN/FO, and primers are typically one of the following products (depending on application): PETN, semi-gelatin dynamites or a nonnitroglycerin water-gel slurry.

Jan 1, 1982

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

The Kaldo furnace is a type of top-blown, rotary reactor that is widely used for the production of precious metals. During the production of doré, a gas jet of compressed air is injected through a water-cooled lance to impinge upon the molten bath surface in the presence of molten metal and a slag phase. A common problem during operation is the difficulty in controlling the distance that the injection lance can penetrate through the reactor mouth without being splashed by the molten phases. Splashing may produce accretions on the lance surface as well as plugging of the nozzle at the lance tip. An additional problem may occur when the gas jet impinges upon the furnace wall and causes rapid wearing of the refractory linings. Because the conditions prevailing in the Kaldo furnace offers poor visibility to the human eye, its operation mostly relies on the empirical knowledge of plant operators and process engineers. A systematic study in a scale model of the Kaldo furnace under controlled laboratory conditions may be valuable to estimate the maximum penetration distance of the injection lance, and thus help improve the operation of an industrial reactor. From a fundamental perspective, the observation of the basic features of the flow patterns in the scale model may help elucidate the relevant phenomena governing the hydrodynamics in this type of system.

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By J. Mark Richardson

Steady-state flowsheet simulators for mineral processing plants have evolved to a current high level of utility and accuracy. Reliable, general-purpose, semi-empirical models now exist in nearly all unit operations categories particularly in the areas of comminution and classification. .These models, installed as user-selectable functions within the integrated frame- work of flowsheet balance-solver software systems, can be strung together to represent any plant configuration. In addition, CAD-like graphics, data reconciliation and model parameterization functions have become standard features of the current generation of integrated plant simulators. These advances have given engineers the capability to investigate many different plant scenarios while requiring a minimum of actual plant testwork. This paper describes a methodology and an integrated software package which are being successfully applied in a number of operating plants worldwide to predict plant performance under changing conditions. Those conditions which can be changed include effect-of ore type, feed size, water addition rates, equipment geometries and flowsheet modifications. By using data from actual plant optimization exercises in real mills, the paper illustrates and out- lines a technique which includes plant data collection, ore breakage testing, flowsheet simulation, model-fitting (parameterization), data adjustment and model experimentation. Brief descriptions of some unit operations models, such as autogenous mills and cyclones, are provided as examples of the current state of such models. Ore breakage testing and its relation to certain models is also discussed. Computer- generated size-distribution graphs, along with tabular data generated by the simulator, round out the presentation and serve to demonstrate the real- ism and accuracy of the models. The paper concludes with a partial list of cases where this technology has been successfully applied.

Jan 1, 1992

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By J. A. Bowersmith

The environment in which the surface mining industry operates today is considerably different than that of a few years ago. Increased pressure from the public, government, labor and internal industry factors calling for the fulfillment of rapidly changing expectations is especially intense in the surface coal mining industry. Such things as requirements for increased production, the Mine Health and Safety Act, environmental concerns and land reclamation, shortages of qualified and enthusiastic employees and market cycles coupled with price competition are but some of the specific items that are requiring the surface mining industry to better utilize equipment, materials, and labor resources available, There is one technical tool available which will assist management to increase productivity, improve cost control and assist in planning, organizing and operating surface mines. Industrial Engineering is that tool. Before a discussion of specific applications of Industrial Engineering to surface mining is conducted, it is worthwhile to review a definition of Industrial Engineering and the history of its development. The following definition has been adopted by the American Institute of Industrial Engineers: "Industrial Engineering is concerned with the design, improvement and installation of integrated systems of men, materials and equipment. It draws upon specialized know- ledge and skill in the mathematical, physical and social sciences, together with the principles and methods of engineering analysis and design, to specify, predict and evaluate the results to be obtained from such systems."

Jan 1, 1976

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By Yi Luo

In a shearer longwall mining operation, the longwall bits are responsible for breaking into and chip-ping the broken coal blocks away from the coal face. However, underground observations have found that a large number of longwall bits are always working under various degrees of wear. Reduction of the bit wear could be realized by using better designed longwall bits and properly selected shearer operating parameters. A computer program has been developed to simulate the performance of the longwall bits. The shape of the bit head, the installation of the bits on the drum and the operation parameters are the information required by the program. Through the simulations, the main factors affecting the bit wearing process are identified. Suggestions are also made for improving the design of the longwall bits.

Jan 1, 1996

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982