Search Documents

By B. Jones, W. Zhang, Q. Li

Rare earth elements (REEs) are critical materials to the United States due to the imbalance between their supply and demand. Considerable research and development efforts have been devoted on REE recovery from coal refuse using inorganic acids as lixiviants, however, the cost of inorganic acids is normally high, and the environmental friendliness is low. As alternatives to inorganic acids, organic acids of small molecules such as lactic acid and succinic acid have been used as efficient and green lixiviants for metal extraction. In addition to the supply risk of REEs, food waste generation and disposal is another emerging and critical issue since nearly one-third of the edible food is lost or wasted each year. In this research, organic acids were microbially converted from food waste and used as lixiviants to leach REEs from density fractions of an Illinois Basin coal. Experimental results indicate that REE recovery increases of up to 15 absolute percentage points were obtained using organic acids relative to inorganic acids. The conversion of food waste into value-added, renewable, and environment-friendly chemicals promotes the economic viability of REE recovery from coal refuse.

Mar 2, 2022

By William E. Foreman

Editor's Note: For purposes of uniformity throughout this book, Coal Preparation, 5th Edition, the editors have advocated the use of the U.S.A. Sieve Series of testing sieves (see Table 6-2) as the testing sieves of modem choice. The adoption and use of the U.S.A. Sieve Series and its forerunner, the Tyler Standard Screen Scale, has for over seventy-five years introduced uniformity into reports; has simplified the comparison of results; and has provided control for operation of modem coal preparation circuits. While a full explanation of the differences, and more importantly the similarities of these two measuring systems cannot be stated here, it is felt that a brief clarification of terms is in order. The difference between the U.S.A. Sieve Series and the Tyler Standard Screen Scale Sieve Series is the identification method. Tyler Screen Scale sieves are identified by mesh designation with the width of opening varying by the square root of two, or 1.414 times the width of opening in the previous sieve. The U.S.A. Sieves are identified by openings in millimeters or microns and also arbitrary numbers which do not necessarily mean the mesh count; this series uses width of opening variations in the order of approximately the ratio of the fourth root of two, or 1.189. Tyler Standard Screen Scale and U.S.A. Sieves can be used interchangeably, and to avoid confusion the nameplate of all Tyler Screen Scale sieves show the U.S.A. Number, while all U.S.A. Sieves show Tyler Screen Scale mesh equivalent numbers on the nameplate. INTRODUCTION Sizing is the process of separating mixed mineral particles into groups of particles all of the same size, or into groups in which all particles range between definite maximum and minimum sizes. This chapter applies the modem mechanical screen and the liquid-solid cyclone (hydrocyclone) to the process of sizing solid particles as applied to coal preparation. Screening is a mechanical process that separates particles by size. Modem coal preparation is made possible by efficient sizing. Sizing of coal is defined in terms of the opening through which an individual particle will or will not pass, or as two openings, the larger of which passes the particle and the smaller of which retains the particle. Screening accomplishes sizing by passing coal of a wide range of sizes through a series of screens, each of a decreasing size. The individual screen discharges are then directed into different screen products for subsequent sale or processing. Screening in modem preparation plants is done for the following reasons: 1. Removal of fine coal before a size reduction step. 2. Size separation of the coal into a coarse and fine fraction for sized products or for processing in coarse and fine coal circuits. 3. Recovery of heavy media from heavy media coal cleaning circuits.

Jan 1, 1991

By I. R. McGowan, J. Tilk, J. I. Hershman, R. L. Lewis

The White Pine Mine is a large underground copper mine located in the Upper Peninsula of Michigan. A numerical ground water flow model of the White Pine Mine was constructed to evaluate potential engineering controls that would reduce the rate of mine-water discharge after closure. Of the passive controls evaluated, the placement of bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35%.

Jan 1, 1998

By Fouad Faraj, Julian M. Ortiz

Within the natural resource industries, there is an increasing amount of data and number of variables being recorded when sampling a site. This has made multivariate geospatial datasets more difficult to analyze, in particular the definition of estimation or simulation domains used in geostatistical analysis. Establishing these domains is typically the first step for any subsequent geostatistical workflows or modeling. Domains are traditionally established using categorical data such as lithology, mineralization, or alteration from geological logging and are aimed at identifying distinct populations with particular geological, spatial, and statistical features. The manual logging process is time-consuming and costly but is required because defining geologically homogenous volumes is crucial for the planning, extraction, and processing of natural resources. Classical clustering methods have aided in analyzing the multivariate datasets, but the resulting clusters from these methods do not correlate well with geological logging and do not allow practitioners to input their knowledge of the domain in the clustering process. In this work, a simple unsupervised classification workflow is presented which allows the practitioner to input domain knowledge by selecting relevant variables to cluster reasonable geological domains. This can be used as a tool to aid the manual logging procedure or as a tool to establish domains for different uses such as defining zones with different rock hardness distributions which allows the corresponding volumes to be sent to appropriate mills for efficient mineral processing. The performance of the workflow is assessed on a mining dataset using the geochemical information and validated with the geological logging.

Apr 16, 2021

By Michael Gobla

"Since 1994 the Bureau of Reclamation (BOR) has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has, to a limited extent, applied risk analysis to inactive and abandoned mines to evaluate tailings dams, pit lakes and flooded underground mines. Case histories of potential failure mode analysis, as applied to mine impounded water, illustrate what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first.IntroductionImpounded water and high water content wastes at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (4.1 million m3 or 5.4 million cu yd) release, the Mt. Poly Tailings Dam failure in British Columbia in 2014 (4.4 million m3 or 5.8 million cu yd) release, and the Samarco Fundao Tailings Dam failure in Brazil in 2015 (59 millon m3 or 78 million cu yd) release have renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originate not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes and flooded underground mine workings.Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the U.S. Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984, the agency developed and began using risk analysis methods. BOR operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of 100 years. Many of these facilities were designed and constructed prior to the development and adaptation of modern soil mechanics in dam engineering. Diligent observational monitoring, detailed site investigations and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high-risk sites, significant improvements to dam safety have been achieved."

Dec 1, 2016

By Charles H. Jacoby

Introduction Although, in general, the openings created in domes or diapiric type salt deposits during mining operations are larger than those created in bedded deposits, the openings in bedded salts are of significant lateral extent. Thus, this paper will deal primarily with the dome deposits of the Gulf Coast and more specifically with the Avery Island dome operated by the International Salt Company where recent development activities have materially increased the sizes of previously standard openings. Geology The geology of salt deposits is the governing factor in the rock mechanics associated with the opening which is being created in the salt. Bedded salts are customarily characterized by having experienced solution along the interface between the top of the salt and the overlying bed. Thus, as the salt slowly dissolves there has been left behind a layer of laminated insolubles which is often incompetent. In most cases, this incompetent rock must be supported by a thickness of bedded salt which is left in the roof as support. Where this salt is of secondary deposition (recrystallized halite) with included moisture, additional thicknesses of roof salt are necessary to achieve stability. The salt which forms the domes of the Gulf Coast regions is from the Louann formation of the Jurassic period. These formations are dipping toward the Gulf of Mexico so that the upper tier of domes which have formed across northern Louisiana in an east-west direction into Mississippi and Texas have a salt source some 10 to 15,000 feet

Jan 1, 1976

By F. J. Susko

The Bureau of Mines investigated rapid bubble-pulp separation to improve flotation kinetics. A shallow-depth froth separator was employed to quickly recover the mineral-laden bubbles from a mixture of ore, water, and air bubbles. The shallow depth minimized the rising distance required to recover even the smallest size bubbles (100 ~m). Therefore, the slurry remained in the unit only long enough to recover the bubbles before the pulp exited through the conical bottom. Joining this unit with a rapid bubble-particle attachment unit, a rapid flotation system was formed that floated silica from phosphate in one-fifth of the retention time for conventional mechanical cells. The hydrodynamics of the rapid flotation system along with fundamental parameters for scale-up are presented in this paper.

Jan 1, 1992

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986

By Dale E. Hirschfeld

The clays in Eastern Washington occur in a variety of forms and are extracted for uses in Face Brick, paper coatings, and aggregates. Not in large volumes in comparison to other areas, not even from impressive large mines. However, mans utilization of these clays has progressed from historical clay tablets to the present technically oriented manufactured products of today. White Face Brick, perhaps the whitest produced anywhere is the unique product produced by INTERPACE CORPORATION's Mica Plant from these unusual clays. It is this basic characteristic feature of the clay's in the Mica area that differentiate them from the other clay's in this belt. ORIGIN The significant properties of clay's used in Face Brick are plasticity, fired color, fired strength, dry and fired shrinkage, the PCE or Pyrometeric Cone Equivalent, and extrudability. Testing clay's for these properties is standard laboratory procedure. No two clays are alike, and seldom can one clay be substituted for another. Mica White Clays respond favorable to all these properties, but more especially, the Mica Clays fire to a brilliant white color, from almost the natural state. The geologic history of Eastern Washington is largely conjectural because of the absence of rocks representing segments of geologic time. The oldest rocks in this area are the argillaceous and arenaceous sedimentary rocks which have been slightly metamorphosed. These rocks have been correlated with the Belt Series of the Pre-Cambrian age, although some may be older. These rocks were subsequently intruded by granadiorites and related rocks that are considered to

Jan 1, 1971

By G. A. Calboreanu

The deterioration rate of any metal or alloy is increased in a erosion-corrosion application because the passivated surface layer is removed by the solid particles contained in the pumping fluid and the material surface becomes corrosion active again. Numerous attempts were made to engineer a stainless steel with higher hardness and unaffected corrosion performance. Alloys of special interest in such an area are the duplex stainless steels particularly the CD4MCu material which has the capability of being hardened due to its ferrite-austenite microstructure. Unfortunately, the CD4MCu with higher hardness comprises different intermetallic compounds which will increase the corrosion rate. The paper is analyzing the erosion-corrosion performance of a new type CD4MCu with 32% higher hardness and superior wear performance. The corrosion performance of this new alloy is better than the corrosion performance of the common CD4MCu material which the industry could supply. The corrosion effectiveness was evaluated with the Huey test, the potentio-dynamic anodic polarization test and the weight loss test whereas the erosion resistance was established with a low stress ball-on-disk type apparatus. The Wilfley hard CD4MCu material had 39% lower weight loss and 32% smaller volume loss than the common CD4MCu alloy The hardness range of the centrifugal pump parts poured and processed with the Wilfley hard CD4MCu is 320-350 HBN versus 250-255 HBN hardness of the common CD4MCu. After approximately 18 months of experimentation and field testing it was clearly established that the life time of the Wilfley hard CD4MCu is higher than the common CD4MCu and consequently centrifugal pumps were supplied to different customers in North and South America. India and more recently Australia. Sincere thanks to all the A.R. Wlifley & Sons Inc. and Western Foundries Inc. employees who supported and help to implement this work. special thanks to George Wilfley. Dave Cobb. Bill Becker Sr. and Wayne Taylor

Jan 1, 1997

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By W. D. Hausel

The Wyoming Province is an Archean craton which underlies portions of Idaho, Montana, Nevada, Utah, and much of Wyoming. The cratonic block consists of Archean age granite-gneiss with interspersed greenstone belts and related supracrustal terranes exposed in the cores of several Laramide uplifts. Resources found in the Province and in the adjacent accreted Proterozoic terrane include banded iron formation, Au, Pt, Pd, W, Sn, Cr, Ni, Zn, Cu, and diamonds. The Province shows many similarities to the mineral-rich cratons of the Canadian shield, the Rhodesian and Transvaal cratons of southern Africa, and the Pilbara and Yilgarn blocks of Western Australia, where much of the world's precious and strategic metal and gemstone resources are located.

Jan 1, 1991

By H. H. Murray

Abstract. World reserves of bauxite are abundant. Domestic reserves are limited and as a consequence the United States must rely on foreign suppliers for over 90 percent of its bauxite. Nationalization of many bauxite mining operations, levying of higher taxes, increased production and transportation costs, and attempts to create a uniform market price combined to place the United States in a vulnerable position. Alumina from kaolin, alunite, anorthosite, and oil shale have-been-or are being evaluated. World bauxite reserves are increasing and attempts to establish a uniform price have failed; therefore, it may be many years before domestic non-bauxite sources of alumina can compete with imported foreign bauxite.

Jan 1, 1980

By Gene E. McClelland

4.1 INTRODUCTION Metallurgical testing is required on any ore, waste or tailing material before amenability to heap leaching treatment can be accurately determined. The amount of testing necessary to determine and optimize heap leach amenability and conditions for any feed material is determined by the ore type, grade, size of deposit, and the overall financial commitment a particular company is willing to make. It is very easy to either "under-test" or "over-test" a particular deposit or feed material. A good heap leach testing program will provide the necessary design information without "bogging" down in too much detail. The three basic stages of ore testing include: • Preliminary--bottle roll tests and small column percolation leach tests; • Detailed--larger column tests, different feed sizes, and feed size optimization; and • Pilot-Scale--Column or field heap. The following subchapters describe the stages of heap leach testing necessary to put a viable property into production. 4.2 PRELIMINARY METALLURGICAL TESTING The two types of preliminary tests that can be undertaken include bottle roll or cyanide agitation tests and small column leach tests. Each of these is described below, along with information about what the test results provide in terms of furthering knowledge of ore qualities. 4.2.1 Bottle Roll Tests The first step in a heap leach testing program is preliminary bottle roll tests at a relatively coarse feed size to determine the ore's leachability. Bottle roll tests are usually conducted on reverse circulation drill cuttings samples (= 1/4 inch (6 mm) in size). Bottle roll tests provide initial information about precious metal recovery, recovery rate, and reagent requirements. The recovery results are to be considered maximums because attrition grinding creates fines and liberates recoverable values that would not be liberated from the material during a static leach. Bottle roll tests can be conducted on up to 25 lb (11 kg) ore charges of up to two inches (50 mm) in size. However, the coarser the feed the more attrition grinding occurs during rolling.

Jan 1, 1988

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the bubbles, water, and ore, selectively attaching these bubbles to the hydrophobic mineral's surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. The rapid flotation system was evaluated for beneficiation with a western porphyry copper ore containing 0.67 pct copper, and a phosphate-bearing amine flotation tailings sample containing 9.5 pct P2O5 in a quartz matrix. Over 88 pct of the copper was recovered from the ore in a rougher concentrate containing 5.9 pct copper at a rate 7 times faster than conventional flotation. Sixty percent of the quartz in the phosphate-bearing sample was floated at a rate 4 times faster than conventional flotation. The unfloated product retained 80 pct of the phosphate in a l6.9-pct P2O5 concentrate.

Jan 1, 1993

By Douglas J. Uhren, Gary W. Gilbert

This paper describes the risk elements associated with difficult glacial geology, including boulders, heavy groundwater inflow, and potential running soils all coupled with a potentially corrosive service environment. The matrix workshop for the 168-inchfinished diameter sanitary sewer interceptor tunnel in Columbus, Ohio is assembled with the Design Team and the Owner’s design, operations, and fiscal staff. Corrosion protection alternatives are compared against cost and non-cost parameters with relative risk and weighting factors assigned. The Owner working in cooperation with the Design Team uses the matrix workshop to se

Jan 1, 2001

Microprocessor-based balances are helping Keffler & Rose Coal Preparation Co. to test and ship coal faster than the competition. They provide a high level of accuracy in meeting Environmental Protection Agency standards and customer specifications .and help minimize "bad" coal. The combination of speed and accuracy has helped increase K&R's sales, while improving the company's reputation for meeting precise client requirements. The quality of coal that is assured by the company's testing-at an in-house lab using fast, precision weighing, and a computerized sulfur test-has assured K&R of a good price for its products. Recent EPA standards have strained the testing capabilities of coal suppliers. Companies involved with high-sulfur coal often use outside laboratory services that can take three to four days to report test results. Since the coal business moves much faster these days, some coal companies cannot afford that kind of time. Too much coal not up to specifications could be produced within a three or four day period. Keffler & Rose took a novel approach to this problem, installing its own in-house laboratory. The test situation immediately improved with this step. However, one bottleneck persisted for a time: the weight measurement procedure for ash, moisture, and energy content. The company first employed a mechanical balance that required time for setting up and taring. The balance provided readings on a conventional scale that was not very precise and allowed for error through subjective readings by the operator. The balance bottleneck was broken when K&R applied new technology to meet its needs: microprocessor-based weighing. The result has been a 75% reduction in weighing time and a sharp increase in accuracy. This has contributed to the test speed needed to keep up with 227-t/h production and precise K&R coal specs.

Jan 11, 1980

By R. J. Cornelius

Gold with minor associated copper mineralization in the area of what is now the Bougainville porphyry copper deposit has been known since the 1920s and was probably known in German colonial times, pre- 19 14, although no records persist other than a reference by Stanley (1922) to copper specimens from Kieta that he saw in Rabaul. Stanley did not at the time believe that they came from Kieta. Gold was first discovered at Kupei by Jack Comb in 1929 and the Kieta Goldfield was proclaimed in May 1930. In December 1932, the Tapu Reward Claim at Moroni - the site of the Bougainville Copper concentrator, was pegged by C.W.M. Evans who prospected up river from the West Coast. The Pumkuna (Panguna) Reward Claim on the site of the subsequent porphyry copper deposit was granted in February 1934 to G.A. Myers. n May 193 1, the Kupei Reward Claim was transferred to Bou- gainville Gold Options NL and later reverted to Jack Comb and then the Bougainville Syndicate, as did the Pumkuna and Moroni claims. Most of the interested parties had come from the Edie Creek rush on the New Guinea mainland. In 1935, N.H. Fisher, the geologist in Rabaul for the New Guinea administration who later became director of the Australian Bureau of Mineral Resources in Canberra, reported on the three gold areas. Norm Fisher described the gold and copper mineralization and its habit in great detail and this report had a major influence on the events leading to the discovery in the 1960s. Gold production up to the Japanese invasion probably did not exceed $50,000 in value. Half a ton of copper-gold ore from Kupei was sent to O.T. Lempriere's in Sydney for assay in the early 1930s.

Jan 1, 1991

By Stryker Magnuson

While probe drills are not strictly necessary for all projects, the incorporation and use of probe drills and pre-grouting adds capability and insurance to boring operations. Water ingress and unstable ground can be resolved before becoming a problem and resulting in costly delays through the use of enhanced, 360-degree probe drilling setups. To do this, proper design of the array of drill ports in the shield, matched to the possible ground conditions, is critical. For ground with exceptional water and instabilities expected, additional probing locations are low-cost additions that can lower risk and increase efficiency. In this paper we will look at recent and ongoing projects including the Lower Meramec Tunnel and Jefferson Barracks Phase 2. We will detail the design of those probe drill arrangements, and our overall recommendations for probing/grouting systems that best suit challenging ground conditions and keep projects running smoothly.

Jun 13, 2023

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997