Search Documents

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By D. R. Barker

The economic performance and competitiveness of a concentrator are dependent on the production of accurate real-time assay information and the manner in which it is utilized. Our paper describes the relative merits of on-and in-stream analysis techniques and the economic significance of Assay-Based control and Target Oriented Display Systems. At Outokumpu's pyhasalmi Concentrator, a Flotation Expert Display System aids the process operator to make better decisions and provides guidance on the most efficient method of achieving the desired control objectives.

Jan 1, 1989

By William E. Mead

A regional investigation to find large supplies of potable ground water was carried out at elevations exceeding 12,000 feet above sea level on the Bolivian Altiplano. The program marked the first application of modern ground water search and development technology in the region, and ended a history of unsuccessful exploration efforts to locate important supplies of fresh water from underground sources. Oruro, a population center of 90,000 inhabitants, and its primary supporting industry - mining, both derived major direct benefit from the results of this program.

Jan 1, 1970

By Tso-Min Shih, Ching-Hua Liu, Chung-Jen Lin, Hsi-Chiang Fang

This paper presented herein, describe the special design of an open type coal dust explosion apparatus and the laboratory works for investigating the effectiveness of the parameters on coal dust explosion and the prevention of the propagation of the coal dust explosion flame. Coal sample which were taken from the San-Ying collieries, were passed through the process of crushing ,grinding and screening to get the required particle size, ranged from 40 mesh to 200 mesh under size for testing purpose, the rock dust spreaded on the surface of coal dust and water mixed with coal dusts were employed for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1991

By Robert A. Westman

The INRED process has been developed step by step by Boliden since 1972 at MEFOS, the Foundation for Metallurgical Research, at Lulea in Sweden. The demonstration - plant is number five in this series. The purpose of this plant, which has a nominal capacity of 60,000 tonnes per year of hot metal is to: 1) prove the process on a sufficiently large scale to provide the basis for construction of production plants, 2) test various kinds of raw materials on behalf of licensees, 3) train operators of the first production plant, 4) develop the process further for special applications.

Jan 1, 1983

By R. L. Grayson

Productivity achievements in underground coal mining over the past ten years highlight the improvement of management practices as well as the adoption of new technology. Research findings and results from operational studies characterize the aspects of good management that translate into high productivity. In concert with these findings, the Mine Management Support System (MMSS) is being developed, under co-sponsorship of the U.S. Bureau of Mines and the West Virginia University Energy and Water Research Center, as a knowledge-based system to enhance more efficient management of underground coal mines. Concentrating on capturing the intricate knowledge needed to manage a mine effectively, MMSS will encompass information and rules on work scheduling, desired work practices, regulations impinging on operations and planning, responses to operating problems, and the labor-management work agreement.

Jan 1, 1990

By R. C. Gilmore, A. Juganda, Jr. Bogin, S. Saki, S. A. Lolon, J. F. Brune, Jr. Zipf, J. W. Grubb

"Methane-air mixtures form explosive gas zones (EGZs) in underground longwall coal mine gob ventilation systems. Such EGZs have caused a number of fatal mine explosions, including the 2010 disaster at the Upper Big Branch mine, where 29 miners lost their lives. Researchers at the Colorado School of Mines use Computational Fluid Dynamics (CFD) modeling to predict EGZ locations. In this paper, a model of a bleeder-ventilated gob system includes two adjacent panels, an active longwall and a mined-out gob. Boundary conditions for the simulations match statutory ventilation conditions for methane concentrations and air flow rates at common measurement points throughout the mine. The modeling results predict the persistence of EGZs in the gob that may compromise the effectiveness of the bleeder ventilation system. INTRODUCTION Mine operators must maintain statutory air flow and air quality requirements at various locations throughout the mine ventilation network. U.S. regulations generally require mine operators to establish bleeder ventilation systems surrounding longwall gob areas (30 CFR §75.334.) Gilmore et al. (2015) documented that explosive gas zones (EGZs) exist within bleeder-ventilated gobs and may extend into the bleeder entries that must be examined weekly, presenting an immediate fire and explosion hazard to mine examiners. In a project funded by the National Institute for Occupational Safety and Health (NIOSH) under contract 200-2009-31409, researchers at Colorado School of Mines have developed a tool for modeling gob air quality using Computational Fluid Dynamics (CFD). This CFD model is capable of examining a wide range of longwall mine ventilation systems. Marts et al. (2014a, 2015) studied progressively sealed gobs with U-type ventilation and using a back return. Saki et al. (2015) examined the impact of gob ventilation boreholes and face air quantity effects on tailgate methane concentrations. Gilmore et al. (2014) modeled bleeder-ventilated gobs and Gilmore et al. (2015) studied the effects of bleeder regulator settings on EGZ volume and locations in the gob. CFD studies for progressively sealed gobs were generally carried out using 5000 ft (1500 m) panels because the gob atmosphere remains largely unchanged from about 500 m (1,500 ft) inby the face. A modular meshing methodology (Gilmore, 2015) permitted researchers to extend bleeder models to 10,000 ft (3050 m) to include the full extent of bleeder entries. This paper further expands the bleeder CFD model to study the gob atmospheres of two adjacent longwall panels, each 10,200 ft (3100 m) in length, with the active face located 6,700 ft (2040 m) from the startup room."

Jan 1, 2016

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By Robert C. Ellman

Lignite and subbituminous coals are utilized essentially as mined without beneficiation. Most of the present production is used to generate electric power and the major problem in this use is ash deposition on fireside surfaces. The preparation at existing mines involves principally crushing and screening operations. Blending of production from different locations within the mine is practiced in several mines to control ash composition. Drying and oil treatment for freezeproofing, of lignite are used to a limited extent during winter. Future processing may involve both washing and drying operations to alter ash composition by ion exchange and upgrade the low-rank fuels to higher heating values. Research has been initiated to determine the feasibility of such processing.

Jan 1, 1969

By Howard N. Egan

The importance of coal as the major energy source has led to wider interest in the recovery of waste coal fines as a usable product. An additional incentive for fine coal recovery has been the increased emphasis on environ- mental pollution control and conservation of the nation's natural resources, Accordingly, a series of studies and tests were performed to investigate the feasibility of the recovery, concentration, balling and pelletizing of coal fines as a marketable adjunct to existing mining and beneficiation operations. These studies were conducted at the existing operations of the Eastern Coal Corporation at Stone, Kentucky, and the Metallurgical Laboratory of Arthur G. McKee & Company in Cleveland, Ohio. The purpose of the investigations was to recover the fines from the effluent waste waters of an existing preparation plant and transform them into a high carbon, low sulfur and ash product capable of being handled with a minimum of degradation and dusting problems. The fines were relatively high in ash content prior to processing, and flotation pretreatment served a combined function of beneficiation, recovery and water clarification, The minus 28 mesh coal concentrate containing 40 to 45 percent minus 325 mesh size material had an ash content varying between 5 and 7 percent and a sulfur content of less than 0.5 percent. Chemical and size analyses of the effluent and concentrated fines are presented in Table I for comparison.

Jan 1, 1967

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By J. Y. Perez, H. M. Ewoldsen, L. L. Oriard

Near the village of Villarino de los Aires, in the province of Salamanca, Spain, is an existing underground hydroelectric power plant. A major enlargement was undertaken to increase the electrical generating capacity, under a contract awarded to a joint venture of Dragados & Construcciones, S.A., Entrecanales y Tavora, S.A., and S.A. Conrad Zschokke. The enlargement required the excavation of an underground system of tunnels, shafts and chambers adjacent to existing facilities and interconnected with these facilities. The existing machine hall and transformer chamber were both extended, requiring excavation of the rock that constituted the existing end walls of these chambers. The drilling, blasting and excavating of the underground system had to be done without damaging existing underground openings or any of the existing structures, equipment or instrumentation facilities. This required careful control of vibrations, air waves and dust. The joint-venture contractors preferred to use electric blasting methods, if these methods could be implemented in a safe manner. The safety question had to be evaluated carefully. High electrical potentials existed at the site because of the electrical generating and transmitting facilities that could not be shut down. Electrical fields were carefully studied prior to the beginning of the work. This was done both in the underground environment and above the ground surface. Special procedures were followed to ensure safety with

Jan 1, 1974

By H. M. Lima, P. Wathern

There are many different words to describe mine closure, including rehabilitation, reclamation, restoration and decommissioning. Closing mining operations, mainly open pit mines, has required resolution of numerous issues. Mine closure plans involve environmental-protection issues, regulatory issues and community issues. The obvious, and often most expensive of them, is the physical rehabilitation of the disturbances and the elimination of long-term commitments and maintenance. This paper outlines mine closure planning and its important component, mine-site rehabilitation. Community consultation and involvement are also referred to as an important component of the mine-closure plans, which are required to ensure satisfactory mine site rehabilitation. Considerations of socioeconomic impact of mine closure and long-term responsibilities are presented.

Jan 1, 2000

By C. Cristoffanini

A real-time transient pipeline simulation was used to model the operational pressure response in the concentrate and tailings pipelines of the Minera Los Pelambres copper mine in Chile. A high-fidelity simulator was needed to train the operators on safe operation of the pipeline for different scenarios. A simulator that solves the transient equations was used to dynamically predict the pressure and flow throughout the pipeline to provide real-time responses to operational changes such as opening or closing a choke valve, or sending a water batch. Slurry rheological properties were incorporated into the model. This paper presents the technical background of the pipeline simulation model and the study of slurry properties. The paper shows the results of the transient simulation for different operating scenarios such as start-up, shutdown and leakage, by presenting the hydraulic gradient curves for each case. Finally, the paper briefly presents how the simulator was connected to an emulated control system and used to train the operator, it demonstrates the most effective tool available to learn to resolve undesirable conditions.

Feb 23, 2014

By Robert D. Brown, Charles A. Sorrell

The decade of the 1980's saw "advanced materials" become a key factor among the industrialized nations, with the United States, Japan, and the European Economic Community being the major competitors. All three have identified communications technology, advanced materials, and biotechnology as the keys to future industrial leadership and the closing decade of the 20th Century is expected to be an era of rapid development and restructuring. The progress of EC'92, the effort to develop uniform standards and remove trade barriers in Europe; the determination of Japan to commercialize advanced structural ceramics, alloys, composites, and superconductors; and the emergence of less developed countries as major supplies of commodity materials pose enormous challenges to the position of the United States as an industrial and financial leader. A consensus is developing that the industries that are first to commercialize the large array of new structural materials and electronic, optical, and magnetic materials and devices will be those who determine the structure of national and world economics. Many technical, economic, legal, political, social, and cultural factors are important determinants in the race to commercialize new materials. Millions of words have been written about these factors and their interdependence; yet the sheer complexity of the problems, the rate at which changes are taking place, and the economic risks involved are so great that government policy makers and industrial decision makers find adequate understanding to be very difficult. Of the many factors involved in advanced materials, the Bureau of Mines has the statutory responsibility to provide information on where materials can be found and how they are mined, extracted, purified, combined, and recycled. It is obvious that minerals availability is essential to implementation of any new technology just as there can be no commodity metals industry if the ores are not available. Because "minerals availability" for commercialization of advanced materials and devices is more complex than for commodity materials and a new mix of materials and processes is emerging, the Information and Analysis Directorate of the Bureau of Mines is redirecting resources to provide reliable information for policy and decision making. The Office of Advanced Materials Coordination (OAMC) was established as a staff operation in July 1987 to assist the efforts of the divisions and branches. The key issues and problems were defined and the role of the Bureau was outlined (Sorrell, 1987, 1988). In February 1990, the functions of OAMC were transferred to the new Branch of Advanced Materials, a line organization parallel with the Branches of Ferrous, Nonferrous, and Industrial Minerals, and was given the responsibility for developing new methods to acquire, analyze, and disseminate information about new materials. The purpose of this paper is to provide definitions, a summary of major issues and problems, an overview of minerals and processing availability problems, and a perspective of the ways in which the mining and materials industries can help to ensure domestic availability of raw and processed materials.

Jan 1, 1990

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By W. M. Houston

Pebble phosphate deposits of Florida have been established from south of Hardee County to north of the Georgia state line or a distance of over 200 miles and mining has been carried out in an ever-increasing scale since 1885. Deposits that can be mined on the economical standards of today, however, are confined in a roughly circular area about 30 miles in diameter, generally within Polk and Hillsborough Counties, in the central part of the State. The phosphate deposit, which is in the Bone Valley formation of the Pliocene age, is covered by Pleistocene terrace deposits of unconsolidated quartz sand. The matrix is composed of approximately 1/3 clay slimes, 1/3 silica sand and 1/3 phosphate pebbles. The phosphate occurs usually as rounded pebbles, ranging in size from about 1 inch down to approximately 400 mesh. The phosphate may vary from well- defined hard pebbles to soft weathered rock. The color and character of the phosphate will range from smooth buff pebbles to black and white or "salt and pepper rock." The screen size distribution varies considerably between locations and the recoverable phosphate varies may extend down to the 400 mesh size in some areas, while in others the phosphate may cut off sharply at about 35 mesh.

Jan 1, 1962

By Gerrit V. R. Goodman, Charles D. Taylor

A technique was developed to determine the fraction of air recirculated from the scrubber exhaust toward the face and the fraction of gas captured by the scrubber. To determine these two values, a series of tests was required. In the first test, gas was released at the face area and concentrations measured at the scrubber exhaust. In the second test, gas was released directly into the scrubber with concentrations again measured in the scrubber exhaust. The simultaneous solution of two independent flow expressions gave values of recirculation and scrubber capture. A series of tests was conducted with various combinations of scrubber flow, curtain flow, setback distance, and machine location. Statistical analyses then were conducted to determine those factors which influenced the levels of scrubber recirculation and scrubber capture in a deep cut. INTRODUCTION As cutting depths increase, the trend is toward the use of blowing face ventilation systems. With these ventilation systems, the potential exists for recirculation between the scrubber exhaust and the intake air stream. One concern is that methane gas, having been removed from the face area, is subsequently recirculated back into the intake airflow. Under these conditions, methane-laden air could be substituted for fresh intake air, leading to increased methane concentrations at the face. There is currently no standard for recirculation between the scrubber and intake airflows. The implied understanding of the Mine Safety and Health Administration (MSHA) is, and has always been, that any recirculation of ventilation air is unacceptable. To minimize recirculation potential, MSHA suggests that operators maintain scrubber and curtain flows within 0.47 m3/sec (1000 cfm) of each other. Given that recirculation may occur in some circumstances, the question arises as to how much recirculation constitutes a hazard for the face workers. Unfortunately, there is currently insufficient information to answer this. Emphasis must instead be placed on means to quantify the amount of recirculation between the scrubber and face area. Methods must also be examined to control this phenomenon. This paper presents a technique for quantifying recirculation and scrubber capture levels in a blowing face ventilation system. Several ventilation parameters are investigated to determine their effects on these levels. DEVELOPMENT OF RECIRCULATION EXPRESSIONS One way to measure airflow quantities at a point near the face would be to measure the gas flow rate Qgas, and gas concentration c at that location. The airflow Qair, would be simply the ratio of these two values, Qair, = Qgas/c. Although gas concentration values, c, can be obtained easily with existing gas monitoring equipment, it is more difficult to obtain gas flow readings, Qgas, at specific locations. To obtain these values of Qgas, another method was needed. Previous work in this area was conducted by Kissell and Bielicki (1975). However, the calculations in their model assumed a constant gas concentration in the region around the continuous miner. In a deep cut, it is questionable that gas concentrations would remain constant or uniform around the mining machine. The technique presented here does not rely on this assumption. It instead assumes that the gas concentration in the scrubber exhaust remains constant. A quantity of gas released at the cutting face either flows into the scrubber inlets or bypasses the inlets and flows around the off-curtain side (in this example, the right side) of the continuous miner (Figure 1). The fraction of the face gas that flows

Jan 1, 1993