Search Documents

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By VASU GANGRADE

Large-opening underground stone mines pose significant ground control challenges, including the risk of massive pillar collapses. These collapses can result in dangerous air blasts characterized by tremendous force and high velocity. Estimating the velocity of these air blasts proves challenging due to the absence of accurate air velocity instruments near the mine portals. To address this issue, this paper proposes a novel approach that leverages closed-circuit television camera footage from the mine. Specifically, it employs the optical flow algorithm implemented in Python to estimate the velocity of the air blasts, providing a valuable tool for assessing and mitigating risks in such mining environments.

Feb 1, 2024

By P. Bottomley, M. Matthews

Maintaining an acceptable thermal environment in South African gold mines becomes increasingly difficult as mining progresses to greater depths where higher virgin rock temperatures are encountered. Current environmental practice offsets the resulting high heat loads by installing large refrigeration plants. However, with the continued escalation of refrigeration costs, it has become necessary to examine other methods for economically combatting the underground heat load. The Chamber of Mines Research Organization has recently been pursuing a programme to devise methods of reducing the flow of heat into underground workings at source. Although there are several sources of heat (such as machinery, men, and explosives), the most significant is that from the rock mass surrounding the workings (Bluhm et al., 1986a). The main thrust of the work has therefore been directed at predicting and devising methods of reducing this heat source. A great deal of theoretical work has been carried out on the prediction of underground heat flow. From a review of this work (Bluhm et al., 1986b) it became apparent that there are two major aspects which require attention, namely algorithms for predicting the heat flow around the advancing stope face, and a correlation of the theoretical work with accurate empirical data. In order to remedy this situation, new theoretical models have been developed (von Glehn and Bluhm, 1986), and heat flow measurements have been made in both a conventional stope (Bluhm et al, 1986a) and in a backfilled stope (Matthews u., 1987). A number of methods for reducing rock heat flow are being examined. These include the insulation of intake airways (Bottomley, 1985 ), backfilling with waste material of the worked out areas, and alternative approaches to the design of mining layouts, the mining method, and the choice of cooling strategy. This paper highlights the heat load reductions that can be achieved by backfilling the worked-out areas and by adopting concentrated mining. The first part of this paper summarizes the results of the measurements obtained in the conventional and backfilled stopes. The theoretical models are then described and comparisons are made with the measured values.

Jan 1, 1987

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By James Parkes

"The proposed Baltimore Red Line light rail system includes a 3.4 mile downtown tunnel (DTT) with five underground stations. The design of the underground stations involved overcoming several challenges, including limited right-of-way, high groundwater and uplift pressures, and metamorphic rock within the station depths. An innovative design was developed to maximize the internal station space while minimizing cost. The station designs use slurry walls for temporary and permanent support and groundwater control. Depths within rock are supported with cast-in-place concrete walls, the thickness of which are minimized through the use of permanent rock anchors for support of the rock mass and slurry wall toes. Permanent tiedown anchors are used for uplift resistance, which minimizes the station depths, volume of rock excavation, and the volume of deadweight concrete. Design considerations regarding individual elements and overall integration of the slurry walls, CIP walls, and multiple anchor types are presented.INTRODUCTION The Baltimore Red Line (BRL) project is a proposed light rail transit line for the Maryland Transit Administration (MTA) that runs east to west through Baltimore City and County. The project includes the Downtown Tunnel (DTT) consisting of 3.0 miles of twin running tunnels, two portals, five underground stations, and a pedestrian tunnel, as shown in Figure 1. The tunnels have an outside diameter of 21.8 feet and are designed to be mined using pressurized face tunnel boring machines (TBMs). The stations, portals, and the pedestrian tunnel are designed as cut-and-cover structures using slurry walls (concrete diaphragm walls) for both temporary support of excavation (SOE) and permanent structural walls. The dimensions of the five underground stations are summarized in Table 1. Design challenges included limited right-of-way (ROW), challenging soils conditions, strong metamorphic rock within the station depths, and high groundwater conditions. The final station designs included innovative use of slurry walls, tieback anchors, rock anchors, and tiedown anchors."

Jan 1, 2016

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By Bob Snashall

Introduction 1300 BC, Egypt. Pharaoh, the god-king, owned all things. He was the only mine operator. As the provider of all things, Pharaoh had great expectations of his officials who gathered the wealth. Pharaoh's official, the mine foreman, was at a gold mine site to see that royal expectations were met. For the official, it could mean a promotion to the good life here and to the godly life hereafter. When he checked the haul for sufficient progress, a lot was at stake. The miner wore a loincloth, perhaps a headband and, if he was a prisoner, ankle manacles. Only an oil lamp helped illuminate the hot, dusty blackness. A fire at the base of the quartz ore face competed for scarce air. The ore so heated crumbled at the prompting of copper wedges. Confined to a crouch, the miner tossed chunks of ore onto a rope-mesh which, when loaded, was drawn up and lugged out. On the surface, the gold was ground to dust. Then it was transported by donkey caravan to the royal depot. There it was weighed, recorded, and distributed to workshops. Many minerals mined Egypt had gold mines to the south in Nubia and to the east in the desert and Sinai. Indeed, gold underwrote Egypt's prosperity. With a constant gold supply, fewer hungry hands robbed burial crypts and tombs. Gold was sacred, "the flesh of the gods." The shiny metal financed the army that policed the desert mining routes and guarded the gold caravans from Bedouin marauders. Gold theft was an offense to the gods. Anyone caught with gold `in his lunchpail,' so to speak, could say goodbye to life, both in this world and the next. In addition to gold, Egypt possessed other mined riches that allowed the Egyptian civilization to flourish. From Sinai and Nubia came copper. So abundant was the red metal that it enabled Egypt to become the supreme power, before the advent of iron. Also mined were amethyst, turquoise, feldspar, jasper, carnelian, and garnet. These were used for the rich inlay work that distinguished Egyptian jewelry and cloisonne. But Egypt's most endurable and awesome material was its stonework - for statues and obelisks and in temples, tombs, and pyramids. Stone quarrying was a vast enterprise. One expedition boasted nearly 10,000 men. These included 5000 laborer soldiers, 130 skilled quarrymen and stonecutters, and - egads! - even 20 scribes. In addition, there were thousands of officials, priests, and officers grooms. There were even fishermen, to provide the multitudes with the catch of the day. Mining methods detailed In 1300 BC, quarrying techniques had changed little since the age of the pyramids some 1300 years before. At that time, in 2600 BC, limestone was locally quarried and fashioned into the blocks of the pyramids. A basic limestone mining method was tunnel quarrying. A ramp was built up to the face of a cliff. A monkey stage was then erected on a ramp. While standing on the stage, quarrymen carved out a rectangular niche in the cliff. The niche was large enough for a quarryman to crawl into. With a wooden mallet, he hammered long copper chisels along the edges of the niche floor to free up the back and sides of the block. The quarryman climbed out of the niche and removed the stage. He then carved out a series of holes in the cliff face for what would be the bottom of the block. The quarryman pounded wooden wedges into the holes. He watered the wedges until they were soaked. The water-logged wedges expanded, splitting the stone along the line of holes. The freed-up block was then levered down from the cliff. On the ground, the blocks were placed on sledges. Men pulled these to nearby water transport. Without block and tackle pulleys, paved roads, and wheels, this was no mean feat. Each block weighed an average of 2.3 t (2.5 st). Whenever possible, the quarrying was done directly from the surface. This "open cast" quarrying also involved using chisels

Jan 2, 1987

By Andrew J. Gaber

Beginning in 1961 the Coal Research Bureau of the West Virginia University School of Mines began a program of research to investigate the potential of the magnetic separation process to remove sulfur of the pyritic form from pulverized coal. Using a so-called isodynamic magnetic separator (1) it was demonstrated that significant quantities of pyritic sulfur could be removed from coal. Pulverized coal samples representing several different coal seams were individually screened into sizes in the 48 mesh by 200 mesh (297 to 74 microns) range, and untreated and steam-air treated samples of each were processed by the magnetic separator. The results of the investigations to magnetically remove pyrite from coal were published in two separate reports issued by the Coal Research Bureau (2,3), The isodynamic magnetic separator was designed about 30 years ago for use in geological and mineralogical laboratories (1,4,5) to isolate one or more minerals exhibiting only small differences in their magnetic propertiese Specifically, to accomplish this, the air gap of the unit was designed to provide a nearly constant magnetic gradient both laterally and longitudinally in the separating zone. It is reported that mineral concentrates of 99.5 percent purity can-be produced on closely-sized fractions after several cleanings through the unit. The isodynamic magnetic separator, therefore, was not expected to process coal containing sizes smaller than 200 mesh, or to demonstrate commercial capability to process pulverized coal. The primary purpose of the Coal Research Bureau in using the unit was that of determining if the magnetic process could remove pyrite from coal, and thereby encourage further research directed toward development of acceptable full-scale processing equipment.

Jan 1, 1969

By W. K. Wedge

The chemical composition of the Pennsylvanian Bethany Falls Limestone Member of the Swope Formation was investigated using optical emission spectroscopy and both flame and flameless atomic absorption spectroscopy. Elements determined were Ca, Mg, Fe, Mn, AI, Si, Na, K, P, Ti, Zn, Cd, Ni, Co, Cu, Pb, Cr, V, and Mo. Over 100 samples were collected from active quarries along a 320-km-long (200-mile) outcrop in northwestern Missouri. Intervals were sampled representing uniform lithology to determine vertical and lateral geochemical variation. The Bethany Falls Limestone is the most extensively quarried Pennsylvanian limestone in Missouri. In 1975, 42 active quarries produced almost 5.4 million tons (6 million st) of stone valued at over 15 million dollars.

Jan 1, 1977

By David W. Houston

The increasing energy crisis, coupled with stringent environ- mental regulations, has created new demands for high capacity materials handling systems with unit train transporting and continuing surveillance of quality control. Effective and efficient methods of material conveyance are through high speed, high volume conveyor belts with the monitoring of quality through the utilization of automatic sampling. When we speak of high speed, high volume belt discharges we are referring to speed ranges from 600 to 750 FPM and volumes as high as 5500 TPH. To achieve the optimum operating sampling system for high capacity belt discharges, it is imperative that two major design characteristics be investigated and evaluated; namely technical analysis of operating conditions through application of ASTM design criteria and practical experience in the selection of equipment and the design of related components. The task of obtaining a sample of reasonable weight to represent an entire lot presents a number of problems and emphasizes the necessity for using standard sampling procedures.

Jan 1, 1973

By J. A. Herbst

Fine coal cleaning by froth flotation has become common practice in the U.S. with more than 80,000 tons treated in this way per day. In spite of this large tonnage, developments in the automatic control of coal flotation circuits have lagged significantly behind those for mineral systems. One reason such developments have been limited is that instruments have not been available for the on-line measurement of carbon or ash and another critical variables in coal slurries. A second reason is that the influence of the operating variables on coal flotation has not been completely understood. During the last few years some of the required instrumentation has been developed and an improved knowledge of the flotation process itself has occurred through mathematical modeling; as a result certain control strategies for coal flotation are beginning to emerge. This paper attempts to evaluate several control strategies using a detailed flotation dynamic simulator, DYNAFLOAT. After constructing a process matrix for the system of interest, promising alternatives for linking manipulated and controlled variables have been analyzed. In order to develop combined grade and recovery control strategies, the authors found it necessary to construct a grade/recovery map with the aid of the simulator to drive the system to known final, feasible grade/recovery operating conditions. Finally, an advanced strategy which uses an on-line model to identify disturbances and take control actions is proposed.

Jan 1, 1983

By L. Barry Phelps

Coal mine drainage, which occurs predominantly as acid mine drainage in the East, is a serious contaminant of surface and groundwater systems (Appalachian Regional Commission, 1969). Treatment of this pollutant can be very costly and is often difficult to achieve (Appalachian Regional Commission, 1969). A major source of coal mine drainage in surface waters is polluted ground- water discharge, therefore treatment of surface water does little to combat groundwater contamination. Prevention of the formation of coal mine drainage and restricting its entrance into the groundwater protects both surface and groundwater systems. The formation of acid mine drainage may be inhibited by preventing contact between toxic spoil, air, and water (Grim and Hill, 1974). This may be accomplished by surrounding toxic spoil with a relatively impermeable barrier, thus restricting groundwater and oxygen flow through the toxic zone. Toxic spoil packages constructed in this manner would minimize the entrance of acid mine drainage into the groundwater system, allowing dilution by uncontaminated water to occur. If successful, concentrations of coal mine drainage would be reduced below toxic levels.

Jan 1, 1981

By N. L. Dorset, K. L. Heasley

Unfortunately, mining and mining accidents have gone hand-in-hand since man first started to extract ore from the ground. In the first published treatise on mining, De Re Metallica, Georgius Agricola (1556) stated that cold, water, dust, stagnant and foul air, roof falls, falls from ladders and demons all caused injury and death in the mines of his day. Although demons are no longer considered a cause of accidents in modern mining, the other factors remain with us still. The United States government started keeping track of fatalities with the establishment of the federal Bureau of Mines in 1910. Successor agencies, such as the U.S. Mine Safety and Health Administration (MSHA) continue to track fatalities today. Looking at the records, it can be seen that coal mine fatalities dropped from 2821 in 1910 to only 27 in 2004. The reduction in fatalities and injuries didn’t “just happen.” It took concentrated effort from the entire mining industry: miners, supervisors, safety officials, mining inspectors and mining researchers. But first, specific hazards must be identified before they can be corrected. In past, coal mining accidents have been analyzed by: type (roof fall, electrical, etc), mine attribute (location, seam height, etc.), and aspects of the mineworker (work experience, job classification, etc). Much of this research helped to direct the industry’s attention to where additional vigilance and safety training was needed. No doubt this directed effort has led, at least in part, to the decrease in coal mining fatalities. This paper takes a novel look at coal mining fatalities: it examines the risk of fatalities based on how long the mine has been open.

Jan 1, 2006

By John C. Edwards, F. Friel, John J. Opferman, Robert A. Franks

A series of diesel fuel fire experiments were conducted in the Pittsburgh Research Center's Safety Research Coal Mine (SRCM) to determine products-of combustion (POC) spread rates along a single entry under zero imposed airflow conditions. Six experiments with an average fire intensity of 330 kW and three experiments with an average fire intensity of 30 kW were con- ducted in a 180 m long entry which had an average 2 m height and 4 m width. POC spread rates were measured by the response time of diffusion type CO detectors, positioned at 30 m intervals, to CO concentrations 5 ppm above ambient. For the 330 kW fires, average POC spread rates of 0.22, 0.1 3, and 0.06 m/s were determined at 30, 60, and 90 m distances from the fire. For the 30 kW fires these average spread rates were reduced to 0.08, 0.04, and 0.04 m/s. The measured maximum roof layer temperature 30 m from two of the 330 kW fire was 30 and 36"C, which is less than the 57°C alarm point of a typical mine thermal sensor. It was determined that smoke detectors can be more effective for mine fire detection than CO detectors. The experimentally determined POC spread rates can be used to provide guidance for specification of sensor spacing to improve early fire detection at zero or very low air flows.

Jan 1, 1997

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

By C. S. Thompson, P. A. Ciullo

Pyrophyllite is a naturally occurring hydrous aluminum silicate with the molecular formula SiO,,AI,,(OH), or, as more commonly expressed, the oxide formula A120,~4Si02~H20. Pyrophyllite is rarely found in deposits as the pure mineral and is often intimately associated with quartz, sericite, kaolinite, and diaspore. These associated minerals, to a large degree, help determine the most appropriate commercial application for a given pyrophyllite ore. Structural similarities plus the generally soft platy nature of pyrophyllite has in the past caused it to be included with talc in applications and production data. The Minerals Yearbook, published annually by the US Bureau of Mines (USBM), still reports on talc and pyrophyllite together, although admitting that they do not share the same uses. Pyrophyllite has also at times been considered a clay mineral because of its structure and chemistry. The refractory properties of pyrophyllite have been known for nearly 200 years, but it has only been in the past 60 to 70 years that a variety of applications have been developed to exploit the unique characteristics of this mineral. Worldwide, pyrophyllite is a component of refractories, whiteware, foundry mold dressings, pesticides, paint, plastics, rubber, cement, fiberglass, and soap. Historical Overview The most salient refractory features of pyrophyllite are its low coefficient of thermal expansion, high thermal conductivity, low moisture expansion, and good resistance to corrosion by molten metals and basic slags. One of the first recorded uses of this mineral was as firebrick in Japan in the early 1800s. This followed its discovery in 1797 on Mount Omotoyama at the site of the present Mitsuishi mine. In addition to firebrick, sawn blocks of ore were used for carvings and in the manufacture of slate pencils and signature seals. The Mitsuishi mine is still one of Japan's largest. By the mid-1800s, refractories were being made in Japan from roseki (a pyrophyllite-bearing ore) for the construction of metal melting furnaces. The mineral did not get its name until 1829 when R. Herman, testing a sample of supposed talc from the gold-quartz veins at the Berezovo deposit in the Urals, showed that it was actually an aluminum silicate and designated it pyrophyllite. This name was derived from the Greek pur for fue and phullon for leaf, in allusion to the effect of heat in causing separation of the laminae in foliated varieties (Mellor, 1927). The exact date of the discovery of pyrophyllite in the United States is uncertain, but it is believed that the talc and soapstone deposits noted in an 1827 report on the geology of the slate belt of North Carolina were actually pyrophyllite occurrences (Olmstead, 1827). Pyrophyllite was first used in North Carolina on a local basis in the early 1800s. Blocks were sawn and cut for use as stove linings, mantels, chimneys, fireplaces, and gravestones. This was the material of choice because it did not shrink when heated, but cut easily and hardened as it weathered. Pyrophyllite crayons were sold commercially by local gold miners for steel marking and as tailor's chalk from about 1800 until 1922. It was during this period that pyrophyllite was discovered near the town of Hemp (later renamed Robbins), NC. The large quantity of scrap resulting from the sawing of crayons at this deposit prompted the construction in 1921 of a grinding plant. The ore scrap was ground to fine granules and sold to asphalt producers to prevent shingles from sticking together. By the mid-1930s, milled pyrophyllite from North Carolina was also being successfully utilized by the ceramics industry in whiteware for its low cost and ability to shorten firing time. Also during the 1930s, pyrophyllite was first used in kilncar furniture in the United States. Canada was another early entrant in the pyrophyllite business. Mining at the Foxtrap deposit on the Avalon Peninsula of Newfoundland began in 1904, with ore shipped to the United States. Production from this deposit was mostly sporadic in the ensuing years until 1956 when mining began for shipment and captive use in US tile manufacture. This production has remained continuous and still essentially captive to the present. The Foxtrap deposit is currently the sole commercial source of pyrophyllite in Canada.

Jan 1, 1994

By Mirza Muhammad Zaid, Nana A. Amoah, Ping Chang, Guang Xu, Ashish R. Kumar

The key takeaway of this study is the significant improvement in dust protection for roof bolter operators in underground coal mines. The optimized canopy air curtain (CAC), with a redesigned two-level manifold system, provides uniform airflow distribution that effectively reduces dust exposure. By enhancing the protection of operators from harmful respirable coal and silica dust, this technology can reduce the risk of diseases such as coal workers’ pneumoconiosis (CWP) and silicosis. The application of this optimized CAC design in real-life coal mining operations can dramatically improve worker health and safety by minimizing dust-related exposure, ensuring compliance with industry regulations and prolonging the lifespan of mining equipment by reducing dust accumulation.

Dec 1, 2024