Search Documents

By R. Weinstein, R. Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Due to the environmentally kind nature of dry jig plants, installation permits are often measured in days, not months. Coupled with all these advantages there has been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But, air jigging isn’t right for every application. There are limitations due to particle size, particle shape, moisture, and near gravity content. This paper explores the evolution of dry jigging; reviews parameters important for determining the suitability of dry jigging; compares historical performance data as measured by imperfection, against results from modern dry jigging technology; and presents actual data from modern dry jig installations.

Jan 1, 2006

By K. R. Gardner, P. B. Altringer, R. H. Lien, B. E. Dinsdale

The Bureau of Mines, U.S. Department of the Interior, is investigating chemical and biological decontamination of complex wastewaters such as tailings pond water containing 280 ppm CN and 5 ppm Se as well as significant concentrations of arsenic, copper, iron, silver, and zinc. The most effective chemical procedure involves cyanide oxidation using hydrogen peroxide or sodium hypochlorite followed by selenium reduction using ferrous hydroxide. The effluent contains ?1 ppm CN and 20 ppb Se; concentrations of other - major contaminants meet National Drinking Water Standards. Preliminary research indicates that biological cyanide oxidation is possible even in highly alkaline solutions (pH 10.5) containing high cyanide concentrations; indigenous bacteria destroyed 85% of the cyanide. Exploratory research shows that other bacteria removed up to 79% of the selenium from chemically oxidized, low- cyanide water. These promising results may lead to a final processing scheme that involves a combination of chemical and biological techniques.

Jan 1, 1990

By PATRICK R. TAYLOR, NICHOLAS BELLUSCI, D. ERIK SPILLER, VICTOR BRAMAN

Most of the world’s production of natural soda ash comes from the mining and processing of trona found near Green River, WY. The processing of trona ores to ultimately yield a high-quality dense soda ash product and reject the insoluble gangue species, primarily in the form of oil shale, is water and energy intensive. It is speculated, however, that the glass-manufacturing industry, which is the largest consumer of soda ash, may be able to use product of a lower grade and consistent level of the insoluble constituents. Thus, the viability of using sensor-based sorting to produce a beneficiated trona stream that would be fed to calcination was investigated. The study encompassed the preparation of a run-of-mine (ROM) Green River ore sample; selection of specimens sized 25 to 75 mm; imaging of the specimens by sensors based on X-ray transmission (XRT), color and laser-induced fluorescence (LIF); insolubles analysis of the specimens; and a bench-scale sorting test. Results of the study established that a correlation between the color of the individual ore particles and their insoluble content exists, and that a surface-detection-based sensor, particularly LIF, is apparently more suitable than XRT to produce a beneficiated trona stream. The bench-scale sorting test demonstrated that a 65 percent separation efficiency and a 70 percent recovery of trona could be achieved.

Feb 1, 2023

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By D. R. East

The concept of sub-aerial tailings deposit.ion using a managed rotational deposition system to form a deposit of partly-saturated tails for North American conditions was introduced by Knight and described by Knight and Haile (1983). The application of the sub-aerial technique, together with continuous removal of all surface waters and underdrainage outflows from the Key Lake uranium mine I s tailing storage facility in Northern Saskatchewan, Canada, has been documented by Knight and Haile (1984). Since then, the concept is being applied in the United States to tailings facilities in California, Nevada, Arizona, Utah, Colorado, Idaho and South Dakota.

Jan 1, 1989

By Richard L. Stotlar

Introduction During the last decade, the metallic minerals segment of the industry could be categorized as a "feast-or-famine" business. It is no secret that metallic minerals are cyclical. Employment opportunities greatly depend on the supply and demand for its mineral products. It is also not unusual for there to be a lag between the industry's manpower requirements and academia's ability to produce new graduates. Due to this lag, there will be years with manpower shortages, as in the mid-1970s. At other times, supply will exceed demand. The question is where will the jobs be in the years to come? This presentation will review reasons why employment opportunities have declined within the metallic minerals industry. It will also predict future demand for mineral engineering graduates. And it will outline strategies for obtaining an employment offer. Historical Review - Employment From 1977 through 1983, about 75% of all metal mining employees were directly engaged in production activities, down from 83% in 1965. This decline reflects increased use of labor saving equipment, and more government regulation and foreign competition. Metal mining's employment decreased from 74,000 jobs in 1982 to fewer than 68,000 in 1983 - an 8% decline. The overall industry is having these problems because of the general downturn in the economy. For example, at the beginning of this decade, US automobile and steel industries were in trouble. Interest rates were too high and volatile. This adversely affected construction, housing starts, and manufacturing. All these industries, being large users of base metals, drastically affected the metals industry. US copper companies are still having problems. Reports indicate that many copper employers have cut production, laid-off workers, and permanently closed mines, refineries, and smelters. A decline in the demand for US produced metal products, such as copper, obviously affects some mineral engineering employment opportunities. Other factors to consider when looking at employment opportunities and why it has become difficult for US metal producers to compete in the world market include: • The grades of ore bodies of many US minerals are considerably lower than the grades of ores being mined elsewhere in the world. • The grades of ore bodies currently being mined in the US are steadily declining. • Foreign producers are largely government controlled and are not necessarily subject to the realities of supply and demand. • US environmental regulations have considerably added to production costs. Foreign producers in most countries do not have to worry about these additional costs. • US mines are getting deeper. This adds to the cost of production because of the increasing distance the ore has to be transported. • Plants and equipment are outdated. Many companies find themselves operating with equipment and plants that need modernizing or replacing. This obviously hinders competitive productivity. • Labor and management have had problems. Work stoppages in certain mining businesses and high wage and benefit costs in relation to foreign producers place US producers at a disadvantage. • Much land is unavailable. The US government owns most of the land considered to have the best potential for minerals development. Most of this land is unavailable for mining or exploration. Therefore, it appears that finding employment with a company whose primary business is mining and processing most metals, such as copper, in the US will be quite restricted and competitive. Future Demand It is difficult to anticipate what key employment opportunities within the next few years will be available to mineral engineering graduates. The Engineering Manpower Commission estimated that US engineering schools awarded 72,471 undergraduate degrees in 1983 vs. 66,990 in 1982. This was the eighth consecutive year in which the number of baccalaureates awarded has increased. On a brighter note, the US government's Occupational Outlook Quarterly stated that the growth rate through 1995 for all engineers is an encouraging 49% over present levels. The estimated number of engineers employed in 1982 is 1.2 million. The numerical in-

Jan 2, 1985

Factors which cause thiourea consumption in gold-leaching systems include adsorption by gangue mineral particles, complexation with base metal ions, thermal degradation, and oxidation by air/ferric iron. Of these factors oxidation by ferric iron is the most significant factor. Of course, ferric sulfate is desired as an oxidant for the gold leaching reaction, but an excess of ferric sulfate leads to high thiourea consumption. In this regard, the rate of gold leaching by thiourea must be balanced against the rate of thiourea decomposition. It is important to note that the thiourea decomposition reaction in ferric sulfate solution is relatively slow in pure solutions and has been found to be first order with respect to both thiourea concentration and total ferric iron concentration. However, when mineral particles from gold-bearing ores or concentrates are present, the decomposition rate can become quite significant. As might be expected, the catalytic activity of mineral surfaces varies with particle composition and size. Experimental results are discussed with respect to the consumption of thiourea.

Jan 1, 1997

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Scott Stebbins

Cost estimating and economic evaluation software provide evaluators with the ability to predict the profit potentials associated with mine design alternatives even during project exploration and prefeasibility. Examining a multitude of development alternatives early on serves to identify aspects critical to profitability and to increase the reliability of economic projections. A case history illustrates how Sherpa Cost Estimating Software, when used in conjunction with Apex Software for Economic Evaluation, significantly enhances an evaluator's ability to examine design alternatives in a timely and reliable manner. The costs and economic impacts associated with various access routes, production rates, equipment mixes, and stoping methods are projected.

Jan 1, 2002

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By Ron Allum, Ed VanDerPas

The application of high speed tunneling in a deep underground copper mine is essential for an ambitious expansion project at Magma Copper Company's San Manuel Mine. At stake is the future of over 1,300 employees at the largest producing full gravity block caving copper mine in the world. A joint venture of Frontier-Kemper Constructor's Inc. and Deilmann Haniel GmbH is helping create that future through the successful application of tunnel boring technology. This paper examines the details required to assemble, deploy and operate a 4.62 m open main beam tunnel boring machine (TBM) in a 1048 m deep operating mine accessible only by shaft.

Jan 1, 1995

By John D. Kalasky

Ventilation is necessary in coal mines to supply fresh air to the working faces for the health, safety, and comfort of the miners, and for the circulation of air to the extent that it will dilute, carry off, and render harmless the noxious or dangerous gases generated. Adequate ventilation depends upon good face control, as well as upon a well designed and properly controlled overall ventilation system. Generally, this includes fans, airways, overcasts, air locks, regulators, checks, and canvas or plastic stoppings near the working places to prevent short circuiting of air, and effective bleeders to maintain a continuous flow away from the working places along the pillar lines at all times and to prevent diffusion of methane back to the pillar line in case of temporary interruptions in ventilation. In the development of a new mine, or the virgin area of an old mine, the main headings should properly be considered a construction project, designed with, only the number of permanently supported (roof) headings required to conduct the necessary air volume to and from the major panels in which mining is conducted by room and pillar or longwall methods. Although subject to hazards from methane quite frequently and requiring constant and careful attention at all times, development of headings has some built in safeguards which make it a less difficult problem in control of methane than exists in pillaring.

Jan 1, 1973

By Brad Grothen, Lok Home

The choice of TBM type is never easy, but it becomes especially challenging when faced with a hard rock tunnel with expected high water flows and pressure. Slurry Shield tunneling has a long history of being used in these conditions to minimize the risk, though this method has brought with it other risks along with cost considerations. At recent projects around the world, another method has been proven to effectively manage these project risks without utilizing Slurry Shield tunneling: Shielded, NonContinuous Pressurized (NCP)-TBM tunneling in rock with a comprehensive grouting program. In this paper, the authors will analyze the use of Shielded NCP TBMs at projects around the world as compared with slurry shield tunneling in rock under water pressure. Recommendations will be given in order to establish a clear picture of the optimal tunneling method.

Jun 13, 2021

By D. H. De Jager

Fluorapatite is an important constituent of the greater part of the basic and ultra-basic rock members of the Complex. The evidence for and role of primary magmatic processes in the development of concentric zones of dunite, pyroxenite, syenite and carbonatite and its consequent bearing on the distribution of apatite are discussed. The presence of at least two generations of each of the latter three rock types indicates the cyclical nature of magmatic activity. Pegmatitic-metasomatic phases corresponding to the major magmatic cycles resulted in emplacement of pegmatoidal assemblages. The abundance of apatite in the pegmatoid can be traced to the composition of its parent magma and its cooling history. Approximately 2.5 million tonnes of phosphate concentrate are produced annually from ores containing from 10 percent to 25 percent apatite.

Jan 1, 1978

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

By K. Hanumantha Rao, A. Javadi Nooshabadi

"Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by chalcopyrite (CuFeS2), which is a copper iron sulfide mineral, during grinding, was investigated. It was observed that chalcopyrite generated H2O2 in pulp liquid during wet grinding and also in the solids when placed in water immediately after dry grinding. The generation of H2O2 during either wet or dry grinding was thought to be due to a reaction between chalcopyrite and water where the mineral surface is catalytically active in producing •OH free radicals by breaking down the water molecule. The effect of pH in the grinding medium or in the water in which solids are added immediately after dry grinding showed that the lower the pH value, the higher the H2O2 generation. When chalcopyrite and pyrite are mixed in different proportions, the formation of H2O2 was seen to increase with increasing pyrite fraction in the mixed composition. The results of H2O2 formation in pulp liquid of chalcopyrite and together with pyrite at different experimental conditions have been explained by Eh-pH diagrams of these minerals. This study highlights the necessity of revisiting the electrochemical and/or galvanic interaction mechanisms between the chalcopyrite and pyrite in terms of their flotation behavior.IntroductionHydrogen peroxide causes nonselective oxidation of sulfide minerals if present in pulp liquid. Oxidation of sulfide minerals takes place when they are exposed to atmosphere and during the grinding process when the particle size is reduced for flotation. The oxidation of chalcopyrite leads to iron dissolution from the particle surface and from a metal-deficient, sulfur-rich surface (Fairthorne et al., 1997). Other studies report the formation of iron hydroxide on the surface with the metal ion dislodged on the surface (Buckley and Woods, 1984; Chander, 1991). The chemical reactions for the oxidation of chalcopyrite in alkaline and in acidic solutions with the addition of oxidants, such as oxygen or hydrogen peroxide, are shown in Eqs. (1) and (2), respectively (Shi and Fornasiero, 2010)."

Jan 1, 2015

By W. M. Schafer

The risk that water quality will be degraded by mining activity can be evaluated using risk analysis techniques. Water quality impacts can occur where water-rock interactions with tailings, waste rock, or leached ore lead to increased loading of constituents into surface or groundwater. Constituent loads contributed by mining facilities are determined by the migration route and chemical evolution of mine water. Mass load contributions from mines can be determined by estimating the prototype pore water in contact with mining waste, predicting the rate and timing of flow, assessing the degree of geochemical attenuation, and modeling chemical mixing with natural surface or groundwater. Mining facility siting and design measures can alter the chemical evolution of mine water by varying the quantity or quality of flow. Stochastic risk management techniques provide a powerful tool for quantitatively identifying the environmental consequences of various siting and design alternatives.

Jan 1, 1998

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By VASU GANGRADE

Large-opening underground stone mines pose significant ground control challenges, including the risk of massive pillar collapses. These collapses can result in dangerous air blasts characterized by tremendous force and high velocity. Estimating the velocity of these air blasts proves challenging due to the absence of accurate air velocity instruments near the mine portals. To address this issue, this paper proposes a novel approach that leverages closed-circuit television camera footage from the mine. Specifically, it employs the optical flow algorithm implemented in Python to estimate the velocity of the air blasts, providing a valuable tool for assessing and mitigating risks in such mining environments.

Feb 1, 2024

By P. Bottomley, M. Matthews

Maintaining an acceptable thermal environment in South African gold mines becomes increasingly difficult as mining progresses to greater depths where higher virgin rock temperatures are encountered. Current environmental practice offsets the resulting high heat loads by installing large refrigeration plants. However, with the continued escalation of refrigeration costs, it has become necessary to examine other methods for economically combatting the underground heat load. The Chamber of Mines Research Organization has recently been pursuing a programme to devise methods of reducing the flow of heat into underground workings at source. Although there are several sources of heat (such as machinery, men, and explosives), the most significant is that from the rock mass surrounding the workings (Bluhm et al., 1986a). The main thrust of the work has therefore been directed at predicting and devising methods of reducing this heat source. A great deal of theoretical work has been carried out on the prediction of underground heat flow. From a review of this work (Bluhm et al., 1986b) it became apparent that there are two major aspects which require attention, namely algorithms for predicting the heat flow around the advancing stope face, and a correlation of the theoretical work with accurate empirical data. In order to remedy this situation, new theoretical models have been developed (von Glehn and Bluhm, 1986), and heat flow measurements have been made in both a conventional stope (Bluhm et al, 1986a) and in a backfilled stope (Matthews u., 1987). A number of methods for reducing rock heat flow are being examined. These include the insulation of intake airways (Bottomley, 1985 ), backfilling with waste material of the worked out areas, and alternative approaches to the design of mining layouts, the mining method, and the choice of cooling strategy. This paper highlights the heat load reductions that can be achieved by backfilling the worked-out areas and by adopting concentrated mining. The first part of this paper summarizes the results of the measurements obtained in the conventional and backfilled stopes. The theoretical models are then described and comparisons are made with the measured values.

Jan 1, 1987