Search Documents

By N. Kuyucak

Uranium ores leached with sulphuric acid typically have poor dewatering properties. Applicability of controlled neutralization where gypsum precipitates as crystalline particles, improving dewatering properties of material was examined. Neutralized material was then dewatered using paste thickener to increase underflow density. The objectives are to maximize water recovery due to water scarcity and to produce suitable cemented paste fill material for optimizing underground ore recovery. Work was performed on acidic slurry samples collected after leaching but before the resin-in-pulp uranium recovery. Controlled neutralization greatly reduced volume of neutralization precipitates giving higher densities and improving the dewatering (filtration) properties. As a result it would be possible to increase the water recycled to the mill. Another benefit is that sulphate in the recycled water was reduced to saturation limit minimizing scaling of process equipment. Additional test work is needed; however, Unconfined Compressive Strength results imply that controlled neutralization increases the strength of paste fill and possibly offers opportunities towards a viable backfill option.

Jan 1, 2010

By J. Donald Rimstidt, Jeanette K. Jerz

Acid mine drainage is a major environmental problem worldwide. A key to remediating this problem is understanding the rate and mechanisms of the complex, multistep pyrite oxidation reaction under geologically relevant conditions. Because many waste piles are not submerged, a large amount of pyrite oxidation actually occurs in air. We have designed a Barcroft-manometer reactor to measure the rate of pyrite oxidation in air as a function of relative humidity and oxygen partial pressure. The reactor consists of two chambers joined by a manometer. Each experiment occurs at constant temperature, initial oxygen partial pressure, and relative humidity, although these variable can be changed between runs. Oxygen consumption was measured and pyrite oxidation rates were calculated from those data. Initial data indicate that rate of pyrite oxidation by oxygen in humid air is much faster than the rate of oxidation by oxygen in solution. The rates determined by this study can be used to develop better remediation techniques for acidic mine waters.

Jan 1, 2000

By K. C. Vories

Surface mining and reclamation has the potential to at least temporarily increase surface runoff and resultant erosion and gully development. This increase in erosion is due in part to compaction of the soil surface with heavy equipment, creation of large relatively unvegetated watersheds, and elimination of natural dendritic ephemeral drainage patterns. Methods for stabilizing gully channels which may develop prior to establishment of sufficient vegetation to control erosion are analyzed. Utilization of various sizes of riprap for channel lining, the use of riprap check dams, reinforcement of riprap check dams, and the relation- ship of type of control structure to area of watershed and resultant flow velocities are discussed.

Jan 1, 1986

By R. D. Call

During the past fifteen years considerable progress has been made in the technology of slope design. It is possible to design rational slope angles if suitable data on geology, hydrology, and rock properties are available. It is of course preferable to conduct a full scale slope design study, but there are those situations where a full scale study is not feasible because of time and budget constraints. In this paper we will treat two situations: (1) choosing slope angles for a preliminary feasibility study at the exploration stage; and (2) dealing with a slope failure in an operating pit. In these instances slope angles must often be chosen on the basis of available or readily obtained data. In an exploration program all too often a feasibility study is initiates just a few months prior to the decision deadline to drop the property or to exercise an expensive purchase option. If all that is available at this point are a few cross sections at odd angles showing ore and waste contacts and a dog-earred map of the surface geology there may not be time to collect and organize enough information for design of slope angles. On the other hand if during the drilling program geologic cross sections are constructed and the structural data is presented in tabular form, rational slope angles can be determined within the allotted time. Certain types of data can be collected only at specific times during a project. Two prime examples are logging fracture intensity and collecting samples for rock testing before the core is split. It is particularly disheartening to ask to see the core and to be shown a tattered cardboard box filled with plastic bags of sample pulps.

Jan 1, 1976

By Giovanni Barla

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The calibration technique of gelatin mixtures, proposed by Richards and Mark in 1966, is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with the view of describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving.

Jan 1, 1968

By M. A. Chandler, G. T. Adel, J. N. Richardson, E. C. Gutierrez

A rapid, bench-top analyzer has been developed to determine P2O5 content and CaO/P2O5 ratio in phosphate ores. The analyzer utilizes a portable computer equipped with a frame grabber to measure the reflective intensity (gray level) of phosphate samples placed in front of a television camera. P2O5 content is related to the average gray level of the sample, while CaO/P2O5 ratio is determined from the amount of bright material present. The sensor is currently being used to analyze flotation concentrate samples at Texasgulf's phosphate operation near Aurora, North Carolina. Sensor development along with results from laboratory and in-plant testing are discussed.

Jan 1, 1993

By Peiwei Xiao, Xiang Li, Biao Li, Haoyu Mao, Nuwen Xu

As an advanced method of rock engineering construction safety monitoring, microseismic monitoring technology can monitor the micro-fracture of rock masses within an effective range, and then perform forecast analysis of rockburst, cracking, falling blocks and other disasters. Although the application of microseismic monitoring technology has become more mature, how to improve its application efficiency remains to be further studied. At present, artificial intelligence has been extensively developed, and the use of intelligent algorithms to improve the efficiency of rockburst forecast can provide a valuable reference for the safe construction of underground engineering. To this end, this paper proposes a microseismic multi-parameter rockburst early warning model based on dynamic Bayesian networks. First, the sensitivity of microseismic source parameters to rockburst forecast is analyzed based on microseismic monitoring data and actual rockburst information of a hydropower station. Second, the main seismic source parameters and their data are selected and imported into a dynamic Bayesian network for learning to obtain the rockburst forecast model. The model is confirmed in its self-validation and K times cross-validation, and the receiver operating characteristic curve of the model is also analyzed, it is found that the area under the curve is close to 1, indicating that the model has good accuracy. Finally, the analysis of the influence strength of the parent and child nodes in the model reveals that the moment magnitude and source scale are the most sensitive parameters, which can be used as an important reference for rockburst forecast.

Apr 26, 2022

By Eric Eisold

The Wachovia Headquarters and Arts and Cultural Campus project in Charlotte, NC includes a 1.5 million square foot, 48-story office tower, two museums, an Afro-American cultural center and a 1,200 seat theater for the performing arts. Public access to the Cultural Campus is through two pedestrian tunnels constructed under city streets connecting to parking garages. The 5.7 m wide by 4.7 m high mined tunnels were procured through a design-build contract. The tunnels were designed as initial/final shotcrete linings with a sprayed water barrier sandwiched between layers of shotcrete. In addition, the mix design was supplemented with a cementitious admixture to develop internal water resistant properties in the shotcrete.

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

Western Energy Co.'s Rosebud mine in Colstrip, MT, has implemented innovative mining techniques in the past,* and following in that tradition, new techniques for overburden removal were recently introduced at the Montana coal mine. In April 1979, falling coal production left Western Energy in a bind. At that time the company was one of the first to implement a dozer/scraper stripping system for additional stripping capacity. This time around, however, the challenge was to eliminate spoil rehandle with a dragline while digging down 33 in. "Rehandle will increase 20% by going down an additional 3 m past the 24-m level," according to Bob Cope, mine supervisor for Western Energy. To cut this additional expense by eliminating the need to rehandle, Western now uses scrapers to bench down for the dragline. This system utilizes the flexibility of scrapers as earthmoving tools. Although scrapers were originally purchased to fill an immediate need for productive, low-cost overburden stripping, they are now benching and continue to optimize the overall effectiveness of existing draglines. According to the company, the draglines couldn't keep up with production requirements if they had to rehandle spoil material. Benching with the scrapers eliminates spoil rehandle. Western Energy expects to produce 10.6 Mt of coal this year from three active pits in the Rosebud mine. Western estimates that there are enough coal reserves at Rosebud to support a 40-50 year operation. The sub-biturninous coal has an energy value of 9.2-9.4 Mj, 0.87% sulfur, 8% ash, and 20% moisture. Pit A, approximately 610 m long and 45-55 m wide, is the mine's greatest producer. A Marion 8050 dragline with a 46-ms bucket digs 30-33 m to uncover the 7.3-m Rosebud coal seam. Here, the scrapers were put to work benching for the dragline. Long Construction Co., which operates the mine equipment for Western Energy, uses four Caterpillar 637 tandem-powered scrapers, two Cat 631s and two Terex TS-24s. The number and combination of scrapers actually used for benching periodically changes, depending on which ones are needed for topsoil removal and reclamation. Scrapers benched down about 9 m and removed nearly 2.3 Mm of over-burden at pit A. About 1 Mm was placed in a 9-m lift on top of the high-wall at the head of the pit. The scrapers built up one side of the lift first and then the other on successive passes to

Jan 2, 1981

By Svante Lundbrink

A new generation hydraulic rock drill featuring more than 50 percent higher performance than other drills has been introduced by Atlas Copco. In conjunction with the new rock drill, control systems have developed and refined to handle the higher drilling output, and to maintain an acceptable service life of drill string components. These improved features are built into the Rocket Boomer, a new high-performance drill rig, used at the recently completed Hanging Lake project in Colorado. Experiences from this project will be reported together with results from a highway tunnel construction project in Italy.

Jan 1, 1991

By Mike Rhodes, Paul Miller, John W. Neale, Vishal Deeplaul, Barrie Hancock, Tony Pinches

The Beaconsfield underground gold mine is one of only a few new Australian gold projects to come into operation in the current climate of low gold prices. Up to 200,000 tonnes per annum of Tasmania Reef ore will be mined and processed over a minimum eight-year life to a depth of 900 metres below surface. The Tasmania Reef is a gold-bearing quartz-carbonate-sulphide vein occupying an old fault structure which transgresses a series of sedimentary beds. The sulphides are predominantly pyrite with lesser arsenopyrite, and also minor copper as chalcopyrite. Drilling to date below this level clearly indicates that the high-grade orebody is open at depth and that the mine life should be extended significantly over time. Since redevelopment of Beaconsfield mine began in the 1980's, extensive exploration has identified a resource of 1.5 million tonnes within a 450 vertical metre zone beneath the old workings, which extended more than 450 metres below the surface. Installation of an 800 litre per second capacity pump station 180 metres below the surface has been critical in overcoming one of the major hurdles experienced during previous operations in the early 1900's. A multi-stage development program, designed to bring the mine into full production, and incorporating construction of the on-site gold treatment plant incorporating bacterial oxidation, has now been completed. Prior to execution of a detailed engineering design of the Mintek-BacTech bacterial oxidation process, a programme of bacterial oxidation testwork was completed to provide a basis for fixing the process design criteria. A flow diagram of the Beaconsfield treatment plant is shown in Figure l. It comprises:

Jan 1, 2000

By Paul G. Greenhill

The Australian Mineral Industries Research Association (AMIRA) was established by the Australian mineral industry in 1959 to develop and manage collaboratively funded research projects. Owned and managed by industry, it coordinates research that answers questions defined by the sponsoring companies of the projects. Now over 35 years old, the Association is an excellent example of what can be achieved through collaborative research and an industry - backed research organisation.

Jan 1, 2000

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

By B. Cristol, G. Benier

Laboratory and pilot tests have shown that the grinding of some aluminas makes two populations appear : agglomerates’ and ultimate crystals’. Classical breakage functions (Size Mass Balance Method) aren't able to describe correctly this kind of grinding. So we have optimized a particular breakage matrix which takes into account the fact that the agglomerates can either be reduced in size or either be blown up to liberate the ultimate crystals. The models which were developed using this breakage matrix are in good agreement with the experimental results of the pilot tests. The industrial breakage functions were estimated from pilot breakage functions, using scale up prediction procedures and plant tests. The agreement between predicted and actual plant performance is excel1ent.A 20 % increase in capacity was predicted to be available by improving the grinding circuit classifier performances.

Jan 1, 1992

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

By A. L. Anderson, J. T. Rybock

Lime, soda ash and similar precipitants have been the industry standard for treatment of acid rock drainage (ARD) because of their proven ability and low per-gallon operational cost. However, these methods carry serious environmental drawbacks and high life-cycle costs. KEECO’s Silica Micro Encapsulation (SME) technology has all the positive characteristics of conventional ARD-treatment systems but none of the drawbacks. SME achieves highly effective treatment in a single step, provides options for ARD prevention and recovery of metals, requires lower capital expenditures, generates smaller volumes of higher-density sludge, consistently passes leach tests, and eliminates long-term liabilities associated with potential metal remobilization and hazardous waste landfilling.

Jan 1, 2000

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By Aldo F. Barsotti

The production and consumption of industrial minerals in the United States traditionally have played important roles in mining and in the supply of the bulk of basic raw materials to the economy. This diverse group of minerals extracted and consumed by a variety of industries accounts, on a weight and volume basis, for most mineral-based products consumed in our economy. Industrial minerals form the bulk of the basic raw-materials feedstock for most of the construction, agricultural, and inorganic-chemical-manufacturing sectors, and a good portion of the transportation, manufacturing, organic chemical, and service sectors of the U.S. economy. In this presentation, I discuss current estimates of the amount and value of industrial minerals mined compared with all mining in 1997. I then present a summary of 1997 production of industrial minerals by several end-use industries. This is followed by a historical perspective of the consumption of industrial minerals as a subset of all basic materials, with special emphasis on the aggregates industry. The presentation concludes with a look at the geographic distribution of industrial mineral operations in the United States and some thoughts about the future.

Jan 1, 1999