Search Documents

By K. L. Woodruff

Shredding is the usual first step in processing municipal solid waste (MSW) for resource recovery. This unit process requires high capital cost and, usually, considerable maintenance cost. In addition, some shredders at times will render certain components of the MSW in a form difficult to recover. This is particularly true in the way metal cans are distorted and the way glass is pulverized. A trommel screen was proposed (1) to pre-process packer truck refuse prior to shredding. Part of the logic for this step is that the portion of raw refuse already within the specified shredder output particle size range would bypass the primary shredder and proceed directly to further processing, such as to an air classifier or secondary shredder. This would reduce the throughput of the primary shredder and allow certain recoverable materials, such as glass, to remain in larger piece sizes, important for recovery. In this way, operating costs for the shredder would be reduced and the recoverability of materials, and hence the revenue, increased.

Jan 1, 1975

By H. K. Lin

Deepwater discharges of sulfide flotation tailings have been practiced for several decades. Oxygen penetration and organic matter content in such environments are the two major factors that determine their reduction-oxidation condition and hence the rate of sulfide mineral dissolution under such discharge environments. In this study, the effects of solution redox potential and pH on the dissolution of some heavy metals from sulfide flotation tailings were examined. Zn, Pb and Cu concentrations in solution were all higher at a higher redox potential and lower pH. Dissolved Zn concentrations reached 100 ppm even at a low redox potential of 105 mV and near neutral pH after 33 days. Pb concentrations were below 2 ppm at 105 mV and near neutral pH after 165 days. At 105 mV, the Cu concentrations were below 0.2 ppm at near neutral pH after 165 days. At pH 2.3, the Fe concentrations were higher at 420 mV than at 105 mV. But at pH 6.8, the Fe concentrations were lower at 420 mV than at 105 mV, due to the oxidation of Fe2+ to Fe3+ and the subsequent precipitation of ferric hydroxide. Arsenic concentrations in solution were all less than 0.002 ppm. For Zn, Cu and Fe, no significant differences were observed between the tests in solutions prepared using seawater and those using distilled water. However, Pb concentrations reached higher levels in solutions prepared using seawater.

Jan 1, 2009

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By R. K. Komarek, F. E. Jr. Briber, G. M. Hanson, Fred D. DeVaney, J. H. Blake, C. L. Matson, T. E. Ban, N. E. Shields, R. D. Frans, R. B. Greenwalt

Metallurgically, the term agglomeration is used to describe processes whose goal is to form balls, briquettes, nodules, flakes, or other sized shaped particles from loose, usually fine, incoherent particles. In practice it includes such varying processes as the briquetting of coal dust and other substances, the balling and induration (heating) of such nonmetallics as cement, fluorspar, lightweight aggregates, etc. It includes such widely used processes as the sintering of nonferrous concentrates, such as those copper, lead, zinc, etc. The agglomeration of specific nonferrous metal concentrates is discussed in detail in the section of this handbook devoted to that particular metal. Agglomeration processes are of particular value to the iron and steel industry where the nature of the primary reduction process, the blast furnace, requires for best results a burden essentially free of fines. This is a change that has taken place since about 1960. Prior to that time many fine unsized ores were fed to the furnace. The development of the pelletizing process gave to the industry a chemically controlled closely sized product that increased the produc¬tion rate and reduced the costs so much that unsized fines are seldom used in modem furnaces. Steel plants produce many fine sized waste products such as fine dust (fine ore coke and gangue) and mill scale. These products, which have a valuable iron content, are usually sin¬tered directly at the plant for reuse. Fine sized ore concentrates are usually pelletized at the mine and shipped as pellets to the steel plant. Common practice in some areas producing natural high grade ores is to screen the ore at the mine to about 3/8 in. The oversize is shipped "as is" and constitutes blast furnace feed. The / in. may be shipped to the steel plant where it may be sintered or otherwise agglomerated. At some mines the fines may be pelletizied prior to shipment. With the development of large ocean ore carriers, and with the transportation of slurried concentrates or fines, a trend has developed of constructing large pelletizing plants or other types of agglomeration plants near large consumption centers (i.e., in the Netherlands or Japan) where ores of many types are brought together, ground if necessary, blended, and agglomerated. As an indication of tonnages of agglomerated materials produced, for iron materials alone (the largest share of the total) production in 1970 in the U.S. was Million gross ton Sinter 40.7 Pellets 43.1 Briquettes, nodules, & others 0.1 Total 83.9 During the 1960s, U.S. production of sinter rose from 40.3 million gross tons in 1961 to a high of 48.7 million in 1964, then settled back to almost the 1961 figure in 1970. Pellet production rose steadily from 14.4 million gross tons in 1961 to the 59.9 figure for 1975. Worldwide, sinter production in 1966 was estimated at 340 million mt (mainly in Europe, Russia, Japan, and the U.S.) and pellet produc¬tion the same year at 64 mt (primarily Canada and the U.S.). World pellet production capacity rose to 200 million tons in 1976.

Jan 1, 1985

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By Dennis F. Koschak

Production tests at Reserve Mining Company's iron ore pelletizing plant established that rubber-lined balling dm produce a green pellet equivalent in quality to those produced in conventional balling drums equipped with reciprocating cutter bars. The flexing action of the rubber liner prevents concentrate buildup in the drums, eliminating the need for a cutter bar. Advantages of the rubber-lined drum includes a reduction in maintenance and operating manpower, reduced bentonite consumption with less drum surging, reduced power consumption, and improved drum on time.

Jan 1, 1983

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By Patrick Corser, Mitch Usibelli

Introduction Coal mining in Alaska's interior, specifically in the Healy area, began as early as 1918 with the construction of the Alaska Railroad. Mining was originally limited to underground operations but has expanded to entirely surface operations. In 1943, the Usibelli Coal Mine was formed and started developing Alaska's first surface mine east of Suntrana (Usibelli Coal Miner, 1984). Production from the local coal deposits has steadily increased and, in 1978, surface mining of Poker Flats was initiated (Fig. 1). Currently, a 25-m3 (33-cu yd) walking dragline strips two coal seams, using an extended bench on the second pass. In addition, a fleet of trucks and shovels are used for coal removal and some limited overburden stripping. In 1984, a contract was signed between Usibelli Coal Mine and Sun Eel Shipping Co. in 1984. Since then, production has nearly doubled to more than 1.3 Mt/a (1.5 million stpy). This article will discuss geotechnical constraints on mining within the steeply dipping coal deposits that exist within the Poker Flats mining area. Specifically, the article will describe how the mining operation retriggered an historic landslide on the No. 5 coal seam (Fig. 2). And the article tells how a mine plan was developed that allowed the coal to be safely removed without inducing additional movement. Regional geology The coal-bearing group in the Nenana coal field is of Tertiary Age. It is overlain in some areas by several thousand feet of Tertiary gravels - the Nenana Gravels. In areas mined by surface methods, the Nenana Gravels have been eroded off, and up to 30 m (100 ft) of quaternary outwash gravels overlay the coal-bearing formations. The coal-bearing group is divided into five formations: Healy Creek, Sanctuary, Suntrana, Lignite, and Grubstake (Wahrhaftig, 1969). Lignite Creek lies on the north limb of a west plunging anticline. This has brought the Suntrana coal-hearing formations near enough to the surface to allow surface mining. Mining is presently in progress on the south side of Lignite Creek in the Poker Flats area. The coal-bearing formation is cut off to the south by a fault having perhaps several thousand feet of vertical displacement, with the upthrust side to the north. South of this fault, Nenana Gravels are exposed on the surface. The Suntrana Formation contain the minable reserves at Poker Flats. This formation is a repeated sequence of poorly consolidated pebbly sandstone near the bottom, grading through a silty fine sandstone to a footwall clay unit immediately below a coal seam cap. The footwall clays are high plasticity clays to silty clays. It has been reported that they contain 30% to 50% montmorillonite (Usibelli Coal Mine Inc., 1982). There are six coal seams in the Suntrana Formation, No. I (the lower seam) through No. 6. Only the top four seams are currently exposed. No. 3, No. 4, and No. 6 seams are the only mined seams. The No. 5 seam is very thin or not present. Portions of the undisturbed Suntrana Formation are overlain by up to 15 m (50 ft) of Quaternary outwash gravels or recent landslide rubble. The surface is overlain by a very thin layer of muskeg and isolated areas of permafrost. In many areas, the outwash gravels are found immediately below the surface muskeg. Numerous landslides have been documented along the north facing slopes of Lignite Creek (US Geological Survey, 1970, and Wahrhaftig, 1958). These appear to be surficial solifluction or skin flow types of landslides. In addition, deep-seated structurally controlled slides are also evident on both the north and south sides of Lignite Creek. Structural features Premining aerial photographs (Fig. 3) of the Lignite Creek slopes in the Poker Flats area indicate substantial evidence of deep-seated landsliding. The landslides noted in Fig. 3 are both inside and outside of the current mining area. Surface mapping and geologic exploration indicate that the coal seams are dipping out of the slopes within the noted slide areas. It is suspected that, historically, these landslides were triggered by undercutting of the toe of the slopes by Lignite Creek. And sliding it thought to have taken place on one or more of the clay beds underlying the coal seams (Golder, 1985). The slide areas are characterized by semicircular head scarps and slumped topography. Based on the premining photographs, these slides do not appear to have been recently active. However, they are expected to be in a state of only marginal stability. Extensive coal exploration indicates that the primary structural feature within the

Jan 1, 1989

By Christopher J. Hall

It has been known for a long time that summing pressure drops and rises due to friction, shock, fans and natural ventilation is incorrect. In fact, lost works and works should be summed. In spite of this, the traditional method of finding a fan/system operating position has been the H/Q Curve. This paper presents (lost) work/m curves, progressing from a single fan moved around the system to include natural ventilation work, and fans in a series, parallel and series/parallel. The solutions obtained graphically are substantiated by dry air thermodynamic solutions, and the traditional solutions are shown to be in error. This method of solving problems is particularly useful when moving fans around the system, and essential in series/parallel and series situations with substantially different fan densities. The dry air analysis is employed because of its simplicity. Real air, with evaporation and condensation, will react somewhat differently, and one should use real densities (i.e.[l + w +w]/va ) when using this method. One source of error when applying this method to real air, although probably not major, will be investigated in a subsequent paper. Friction and shock losses are proportional to the square of the mass rate of flow, leading to the typical parabolic system curve. However, the unbalanced water stuff potential energy term, on a unit mass basis, is substantially independent of the mass rate of flow. It is possible that this could be handled as a negative natural ventilation work.

Jan 1, 1987

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By N. N. Clark, C. M. Atkinson

Pachuca tanks are used widely in the mineral industry for leaching and mixing operations. An analysis has been presented previously to predict circulation of homogenous slurry in Pachuca tanks with full height draft tubes. However, settling of solids causes deviation from the homogenous case. Circulation of settling slurry in a Pachuca tank is modeled and shown to be a function of settling velocity, solids fraction, solid and liquid density, air flew rate, and tank dimensions. The pressure balance is shown to be very sensitive to these parameters, especially at low slurry velocities. Equations for predicting the air requirements in Pachuca tanks containing settling solids are presented.

Jan 1, 1988

By Stanley Lefond

The health of the industrial minerals industry appears to be improving year by year. In fact, preliminary information suggests that only three commodities (asbestos, bromine, and sulfur-other) failed to show a production gain in 1984 over 1983. In 1983, 10 commodities failed to post gains and six remained constant. The total value of industrial mineral production in 1984 was $16.7 billion, up $1.4 billion from 1983. Cement, clays, gypsum, and crushed stone production increased. Since these are used in housing and construction, this suggests these industries are moving out of their recent doldrums. Barite and clay production also improved in 1984. Local US barite production, however, still has a long way to go to attain the 1981 high of 2.6 Mt (2.9 million st). Barite imports remain high. But they are not as high as the 1982 importation of 2 Mt (2.3 million st). Bentonite production in 1984 increased 20% in volume and 25% in value over the previous year. This suggests improvement in the drilling industry and an increase in demand for iron ore pelletizing grades. All in all, the industrial mineral industry is alive and well. And it shows signs of great improvement in the next few years. Many thanks to those industrial mineral technical committee members for their assistance in assembling this industrial minerals review: M. F. Dibble, H. W. Allen, G. H. Gallup, S. G. Ampian, D. W. L. Spry, H. G. Fleshman, and L. J. Czel.

Jan 5, 1985

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

By E. Bonates

Truck/shovel systems are a major form of materials handling in open-pit mines in spite of the high associated capital and operating costs. Mine management is usually faced with a decision to purchase new equipment in order to support the steadily increasing on production. These decisions involve a high degree of uncertainty with respect to future demands and technical developments. This paper describes a computer simulation model for evaluating the optimum equipment fleet in an open-pit mining operation. The system is based on a stochastic simulation program which accounts for the various mining and economic parameters. It calculates the type of equipment and the optimal number of trucks needed to meet the production targets. Two types of selection criteria: maximum rate of production or minimum cost can be applied.

Jan 1, 1989

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

By M. K. Pathak, A. K. Mukhopadhyay, D. C. Panigrahi

Changes in machinery operating and design parameters often result in unexpected vibrations or changes in the vibration patterns. Vibration in a system is an undesirable element that can cause machinery distress. Potential damage can be prevented by identifying the vibration level that is due to the changed operational parameters. This is necessary for the safe and reliable operation of plant equipment. This paper presents a documented study on vibration events that resulted from alterations in operating and design parameters in a mine ventilation fan and analyzes the causes by defining the sequence of events that led to its performance deficiency. This paper is based on experimental effort to study the vibration behavior of a ventilation fan under varying operating conditions.

Jan 1, 1999