Search Documents

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By Fred C. Caspall

During the last century the importance of coal as a natural re- source has frequently come to the attention of the general public, but never before nave circumstances combined to focus as much attention on coal as it receives today. There is the ever increasing demand for energy that can be met only by coal consumption, coupled with a growing awareness of man's potential for despoiling his own environment. Society monitors the use of the remaining resources with an increasingly critical eye and, for obvious reasons, surface mining operations tend to draw an unusual amount of public attention. While the surface mine is a successful economic competitor with other uses of the earth's outer skin, one of the unrewarding results of such activity is tile simultaneous destruction of two of our most important resources--the coal seam and the surface soil. In a relative sense the coal seam is a nonreplaceable resource but the surface soil can be restored. Unfortunately, little attention has been given to land reclamation and even less has been devoted to the restoration of a productive surface soil. The research reported in this paper was de- signed to test the relative productivity of newly reclaimed surface mine spoils in western Illinois. The results are preliminary in nature but may aid in the future redevelopment of mine spoil soils in the Illinois Coal Basin.

Jan 1, 1975

By R. A. Jankowski

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers using six different filter panel designs at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least-dense filter was as much as 33 % lower than the collection efficiency of the most-dense filter. At the low operating velocity, the least-dense filter allowed more than 40% of the respirable silica dust in the scrubber intake air to pass through the unit and back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency regardless of the filter panel tested The density of the filter panels also impacted the quantity of air moved through the scrubber, with higher-density filters reducing scrubber airflow. For each filter, the relationship between dust-collection efficiency and air-moving capacity must be considered to determine the overall effectiveness for each mine application.

Jan 1, 2000

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By Henning E. Soderberg

Yesterday, air pollution was somebody else's problem -- today, it is everybody's problem. The coal industry with thermal coal drying, is aware of their problem and the necessity of doing an acceptable job; however, there is much to be said as to how good a job is required and what performance limits should be set up. American Air Filter Company has been one of the pioneers in the solution of the thermal coal dryer dust problems, Because of high moisture content, products of combustion and occasional temperature surges, only wet collection has been considered as the practical approach. Our first installation goes back some 12 years with a total to date of 29 Individual wet collectors, each, fabricated of suitable corrosion-resistant material, at 14 operating plants. To eliminate a potential air pollution problem, a performance requirement of not more than approximately one-quarter (1/4) grains per cubic foot in the dust collector discharge was used. In nearly all installations, operating performance surpassed requirements, but discharge stacks were not entirely free of discoloration. However, plant nuisance and air pollution complaints were eliminated. This satisfactory performance was accomplished by medium priced wet dust collectors operating at a 4-6" W.G. pressure drop with cater drain requirements of about 1 gallon of drain water per 1000 cubic feet of air exhausted.

Jan 1, 1962

By Paul M. Keyser, Donald G. Foot, Jeffrey D. Mckay

In the past 30 years, there have been tremendous advancements in the uses and applications of column flotation. From their first use as final cleaners that could produce excellent grades at the cost of recoveries, columns are now being used in every stage of the flotation circuit as well as is SX-EW. Columns as roughers, final scavengers and even at the end of CIL circuits, are finding their way into the marketplace. Operational results of these new uses are presented. INTRODUCTION Flotation columns have been in use since the early 1950's in the U.S. (Hollingsworth, 1952) and the early 1960's in Canada (Trembley, Boutin, Wheeler, 1963). Application of column flotation has been somewhat diverse. In the early years, columns were used predominately for molybdenum cleaning in Canada and for phosphate flotation in the United States. Unfortunately, results met with skepticism and disdain as the columns were hard to operate, temperamental and although producing high grades, could not achieve acceptable recoveries. Since the inception of column flotation technology, the degree of knowledge for design and operation of columns has vastly improved. Despite improvements in the technology, there is still some reluctance by mineral producers to investigate the use of column flotation cells for processing stages other than cleaner flotation. This characterization is in part due to the proven advantage of flotation columns in reducing gangue entrainment in the froth product which results in higher grade products and/or fewer processing stages. Also, during the development of column technology, different types of spargers have been used with varying degrees of success. Furthermore, the general knowledge base of parameters affecting column flotation design and operation have advanced tremendously. Inefficient, or primitive, sparger design, coupled with the lack of column design and operating knowledge and experience, resulted in poor metallurgical and mechanical performance in many cases. Unfortunately, this lack of knowledge caused many column installations to be characterized as failures. The industry felt that columns could not achieve high recoveries, especially when dealing with coarse particles. Therefore, columns were characterized as cleaners, where low recoveries could be tolerated as recirculating loads rather than direct losses and froth cleaning advantages of the quiescent column flotation regime could be realized. Fortunately for the minerals industry, some producers have stood at the forefront of technology and allowed the column to be utilized for new applications. In the last decade, column flotation applications have expanded to virtually every mineral system and plant location throughout the world. The expanded application of columns has generated a new wave of interest for processing various streams. One of the most notable is in the use of columns as rougher cells. This is of particular interest to "green-field" plants and plants where expansions are taking place. Here, metallurgical superiority can be combined with maximum capital and operating cost advantages for a rapid return on investment. The superior results experienced to date, have generated a cohesive vision of the future in mineral processing where flotation columns function as single stage primary separation devices (roughers) with a single stage cleaner, if necessary. The advantages of column flotation go far beyond their original uses. We now have seen columns used as final tail scavengers, in SX-EW plants and even at the end of CIL circuits. Some of these cases will be reviewed. CASE STUDIES In an attempt to show the diversification of column flotation to many facets of the mineral processing plant, a variety of case studies will be discussed. Some of these were designed by the authors while others have been provided by plant sources. It is important to note that in each successful case, the columns were designed using the author's design and scale-up approach. This method assures that the columns are designed correctly for their particular application. For successful

Jan 1, 1993

By G. M. Wilemon, B. J. Scheiner

The Bureau of Mines conducted investigations on extracting phosphate values from fine-particle wastes generated during the mining and beneficiation of phosphate ore by leaching dried wastes using a H2SO4-methanol mixture. Although phosphatic clay waste contains up to a third of the phosphate originally present in the ore, recovery of these values represents a significant challenge due to the fine grain size of the material, the particles averaging less than one micrometer in diameter. Waste samples obtained from two Florida producers yielded phosphate extractions of 71 and 84 pct, respectively, when leached under ambient conditions and at a stoichiometric acid ratio of 1.4:l. Elevated temperatures did not improve the amount of phosphate extracted. Undesirable A12O3, Fe2O3, and PlgO impurities were largely rejected; higher grade wastes gave acids that meet established industry impurity standards and lower grade samples yielded acids that marginally fell short of the standard. Separation of the crude acids from the insoluble residues was accomplished via vacuum filtration through either filter paper or commercial filter cloths. Both filtration rates and solids retention were improved by the addition of 0.5 lb/ton of poly(viny1 acetate) (PVAc) or poly(ethy1ene oxide) (PEO) to the methanol-acid slurries. These results show potential for substantially increasing the reserves of an important domestic resource.

Jan 1, 1989

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

The ventilation conditions at the underground coal mines are influenced; first: by the disturbances of the natural nature (barometric pressure, methane liberation, etc.), and second: by the disturbances caused by the production process. The major goal of this study was to determine the changes of the ventilation parameters, such as the flow, pressure and methane concentration around the longwall panel, particularly, along the longwall face due to the shearer operation (motion). It is well known from the practice, that the movement of the shearer influences the ventilation parameters around the longwall panel, including the gob area. Until now, these data were gathered in a single or multiple locations at the different time. However, only the simultaneous measurements of all of these values allow seeing the time dependent interrelationships between measured parameters. To be able to show these interrelationships, special experiments, described in this paper, were carried out by the author. These experiments were prepared and executed at the BUDRYK Coal Mine in Poland. During each experiment a simultaneous measurements and monitoring of the barometric pressure, air velocity and methane concentration at the different locations along the longwall face, were performed. The investigation was possible by using a special setup of instruments with a short sampling time, i.e., within 2 seconds. The monitoring of the absolute pressure was conducted by using the digital barometer µBar, developed by EMAG, based on the SETRA pressure transducer, model 470. The velocity of air was measured using the electronic vane-anemometers, developed by IMG-PAN. The methane concentrations were measured using methanometers as the part of the EMAG automatic gas monitoring system. The investigation data confirmed that disturbances due to the operation (motion) of the shearer at the longwall face have a local character. It could be also seen that a large diameter shearer (compared to the total cross-section area available for the air flow) is acting as the piston compressing the air (the overpressure) ahead of the shearer. This fact affects the methane mixing process and flow patterns in the vicinity.

Jan 1, 2009

By J. W. III Leonard, T. E. Wilson

In addition to coalbed thickness and basic coal quality data, coal drill cores can produce design data for coal beneficiation processes. To generate design data, a coal drill core should be reduced from its original cylindrical form to a particle size distribution and composition that represents (with the possible exception of top size) a raw coal process stream. Reducing a coal core with a crushing machine rarely accomplishes this representation. This investigation employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis to characterize the core in terms of first-order and zeroth-order break- age rate constants, which are indices of the propensity of the coal to degrade during handling. To reduce composition variables and conserve difficult-to-obtain coal cores, the initial drop-shatter and dry-tumbling tests were done with synthetic cores. Then, cores from three coal beds, Illinois No. 6, Upper Freeport and Pocahontas No. 5, were tested. Comparison of a crushed drill core and a drill core prepared by drop-shatter and tumbling indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed.

Jan 1, 2000

By Jie Zhang, Xi Zhang, Yu Wang, Wei Zhao

The study proposes a novel reagent scheme where adding a small amount of citric acid (CA) significantly improves the depression effect of sodium silicate on calcite and fluorite. The flotation results suggest optimal concentrations for CA and sodium silicate, achieving nearly complete depression of the minerals. Theoretical analysis indicates that CA dissolves calcium ions on the mineral surface, enhancing the adsorption of sodium silicate and preventing collector adsorption.

Mar 27, 2022

By Manuel Viveros J.

This paper will deal with the type of rocks so called evaporites, which are sedimentary rocks produced by water evaporation from seas, lakes or marginal lagoons, in warm and arid climates. Salts derived from these deposits are precipitated according to their solubility; that is, the more soluble precipitates first, overlain by other sediments like silts, shales, limestones, sands, etc. The most common evaporites, according to their chemical composition, are : Chlorides Sulphates Carbonates Nitrates Borates Common salt, or halite, sulphates like anhydrite and gypsum, are the most important. Potassium chloride (silvite and carnalite) and potassium sulphate are of great commercial value.

Jan 1, 1974

By M. R. Wormald

A real time data acquisition system has been developed for implementing standard radiometric analytical techniques, applied to the monitoring and control of mineral processing plants. The system uses standard ECB-bus microprocessors and peripherals, in conjunction with a specially designed nucleonic pulse ADC. It is being applied to the accurate on-line analysis of naturally-,occurring radioelements in processing plants, for example by simultaneously measuring the intensity of 1.46 MeV gamma-rays from the naturally-occurring radioisotope K-40, and the stream density by gamma-ray transmission of 662 keV gamma-rays. Gain stabilisation of the NaI(T1) scintillation detectors is maintained by the microprocessor in slave units, each of which may control up to four sample presentation systems. Data analysis - including corrections for bulk density, radioactive decay of the Cs-137 gamma-ray source, pulse pile-up, dead time and external background - is carried out in a master computer which is connected to the slave unit, and can be interfaced to the plant control computer via data links.

Jan 1, 1986

By Cesar A. Busnardo

The carbonatite orebody in Jacupiranga is situated some 230km (140-mi) southwest of Sao Paulo and is mined by Serrana S/A de Mineragao, producing an apatite concentrate for fertilizer production and a calcite tailing for cement manufacture (see Figure 1). The orebody (Table 1) is mined by open pit and the total production is 4.5 million mt/year of carbonatite ore with a further 2.2 million mt/year of overburden. The carbonatite low-grade ore (Table 2) is fed to the concentration plant at 460 mt/h , comprising of four parallel lines of grinding, by rod mills 2.7m x 4.5m (9 x 15-ft), operating in closed circuit with hydrocyclones. The grinding circuit product is deslimed in four stages using hydrocyclones and the deslimed product is conditioned with corn starch and subsequently floated, using fatty acids as collector to, recover the apatite.

Jan 1, 1985

By F. Mielli

Mine operation managers are constantly tasked with identifying new ways to produce more, while using less. Mine effectiveness and reliability is the foundation of improving operational performance. Timely decisions need to be made in order to identify production waste. Intelligent data needs to be visualized in real-time. Operational events need to be captured with impacts quantified and root causes identified. Unfortunately, complex information technology solutions often have a very poor success rate, with some reports suggesting 30 percent of complex projects are canceled before completion.

Feb 27, 2013

By Andrew C. Katen

The mining industry faces increasing geopolitical risk in the coming decades. Constraints such as resource nationalism, corruption and social license could grow to outweigh fundamental limitations like geology or supply and demand (Ernst & Young, 2013; Verrastro et al. 2010). Lurking beneath these more immediate and palpable concerns, however, may be more significant risks entrenched in geography and history. Deep-rooted cultural and strategic forces that emerge slowly ? or erupt suddenly and unexpectedly ? can generate momentous and far-reaching political, social and economic changes. While multinational enterprises routinely assess for political risk, the nature of minerals extraction means long-term and systemic geopolitical conditions are especially important for mining companies to identify and understand. Mine development is a decades-long process that binds companies to the land and makes changing course to avert emerging threats a difficult and costly option. Consequently, geopolitical assessment is a pertinent and valuable tool that mining companies can use to more comprehensively evaluate strategic threats and opportunities. Geopolitics is the study of society, politics and strategy through the lens of geography (Gray, 1996). Its emphasis on relatively permanent physical features of the earth makes geopolitics a uniquely valuable tool for assessing political risk. Topography, climate and natural resources have shaped, constrained and motivated peoples and governments throughout history. These influences transcend regimes, policies and borders ? and even states themselves ? which, by contrast, change often and dramatically. Framing politics against mountains, deserts and rivers supports identification of historical patterns and forecasts of emerging trends. In other words, the physical map provides an objective and consistent model for studying a subjective and dynamic subject such as politics (Sloan and Gray, 1999). Consequently, geopolitical assessment can highlight threats and opportunities that go unaddressed by other risk methodologies that emphasize current conditions (Glancy, 2012). Taken together, the permanence of geography, hindsight afforded by centuries of political history, and interconnectedness of world events makes geopolitical assessment a valuable approach for conceptualizing strategic risk.

Mar 1, 2014

By K. Oraee

Mining Ventures are considered as high risk projects and therefore managing the risks is inevitable. Risk assessment is an important part of the complex process of risk management, hence applying appropriated and practical methods for ranking the risks associated with projects, can help to perform a better risk management. In this research the applicability of using Techniques for Order Preference by Similarity to Ideal Solution (TOPSIS) method for risk ranking in an underground mine, extracting by block caving method, was studied. Via this method, the risk associated with reserve estimation ranked as the first while in conventional method (P-I Matrix method) located in the sixteenth. Also there were significant differences in ranks of the other risks. Considering the more criteria, with different weights, in comparison with conventional methods, the results comprised from TOPSIS method are more reliable. By implementing this method risks are ranked better and more realistic and consequently then will be managed more efficient.

Jan 1, 2011

By Paul K. Sims

The Central City district is one of several adjacent mining areas in the Front Range, Colorado, that contain precious metal-bearing sulfide veins of Laramide (Late Cretaceous and early Tertiary) age. The districts are in the Front Range segment of the Colorado mineral belt, and are characterized by porphyritic igneous rocks of intermediate composition that have intruded Precambrian crystalline rocks in the core of the Front Range. The veins and minor stockworks that constitute the ore deposits in the district were formed largely as fracture fillings. The veins range from simple fissures to complex, branching lodes, and commonly range from less than 0.5 to about 1 m in width. The principal values are in gold and silver. The common metallic minerals are pyrite, sphalerite, chalcopyrite, tennantite, and galena; minor minerals are enargite, pitchblende, and gold tellurides. Quartz, cryptocrystalline silica, carbonates, fluorite, and barite compose the gangue. The ore deposits have a well-defined concentric zonal arrangement. A core of pyrite veins (central zone) is surrounded by a peripheral zone of galena-sphalerite vein with gold and silver. An intermediate zone contains transitional veins that have minerals characteristic of both the central and peripheral zones. The minerals were deposited in three stages during a single period of mineralization: uranium; pyrite; base metals, gold and silver. The wall rocks were altered primarily during pyrite-stage mineralization. Sericite envelopes developed adjacent to fractures, and were succeeded outward by zones of argillized rock. The valuable ore minerals were deposited in ore shoots localized by several types of structural controls, principally vein intersections, the physical nature and structure of the wall rocks, and irregularities along the fractures themselves. During supergene alteration, gold was concentrated in the upper, oxidized parts of the veins, commonly to depths of 50 m. The precious metal-bearing sulfide ore deposits are closely associated in space and time with the Laramide porphyritic igneous rocks and are believed to have been derived from hydrothermal fluids related to the magmatic activity. The ore deposits have mesothermal aspects and apparently formed in the temperature range 200°-320°C.

Jan 1, 2013