Search Documents

By Roy H. Patten

When driving a shallow soft ground bore, the appearance of surface craters along the tunnel alinement indicates trouble, particularly when a major highway is intersected. During the excavation of a 3.7 m diam tunnel in Seattle, Washington a chemical grouting program was implemented to stabilize soil conditions sufficiently to allow advancement of the mole without loss of ground. Unanticipated mixed face conditions consisting of saturated running sand and some boulder pockets bedded on top of dense glacial till created excavation difficulties. A discussion of problems and corrective measures is presented.

Jan 1, 1987

By E. Topuz

Mining equipment, like all other equipment, is subject to failure. Since most failures occur at random and are unexpected, corrective maintenance is usually more expensive and causes more down-time than preventive maintenance. In order to reduce the number of failures and thereby increase the availability of an equipment or system, preventive maintenance can be scheduled at predetermined points of time. The preventive maintenance scheduling policies presented in this paper utilize reliability and probability theories. They can be applied to various production bottlenecks where high cost equipment precludes having sufficient quantities of stand-by units.

Jan 1, 1982

By Apostolos Vrakas, Georgios Anagnostou

"INTRODUCTION The small strain assumption routinely made in tunnel analyses remains sufficient from an engineering point of view as long as convergences do not exceed 10%. More specifically, small strain theory assumes that deformations are so small (in relation to the size of the underground opening) that any geometric change in the continuum can be disregarded (Fig. 1a). In fact, however, the geometry is updated during loading (or unloading) according to large strain theory and thus equilibrium and stiffness are evaluated on the deformed configuration of the continuum (Fig. 1b).In problems involving large deformations, where the undeformed and the deformed tunnel geometry differ significantly, small strain theory leads to erroneous and sometimes even nonsensical results (i.e. it can predict wall displacements even greater than the excavated radius under conditions of very low stiffness and strength, high in situ stress and low support pressure). This can easily be verified from the widely applied relationships for the ground response curve. For example, in the ideal case of linearly elastic behaviour, the convergence of an unsupported opening equals (1+?) s0 / E (where E, ? and s0 denote the Young’s modulus, Poisson’s ratio and initial isotropic stress, respectively) and is greater than 100% for E < (1+?) s0. Although convergences are less than 10% in the great majority of tunnelling projects, very large deformations may take place when tunnelling through weak rocks under a high overburden (Fig. 2). This paper will first present a very simple and practicable way to account for large strains, based entirely on the results of routine small strain analyses, and will subsequently show the importance of addressing large strains in tunnel analysis and design with reference to three typical case studies of tunnelling in squeezing ground."

Jan 1, 2016

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By S. K. Kawatra, A. K. Bakshi

An on-line rheometer was developed to monitor the slurry rheology of a thickener underflow. The thickener processed a chalcopyrite flotation concentrate having a top particle size of 125 µm and a solids content of 30% to 60% (by weight). The slurry also contained residual flotation reagents, resulting in hydrophobic particles. Polymeric flocculants and lime were added to the thickener to flocculate the particles. Using the on-line rheometer, the slurry was found to exhibit pseudoplastic behavior with no yield value. It was also determined that factors other than the percent solids were responsible for changes in the slurry rheology.

Jan 1, 1999

By V. K. Gupta

The phenomenon of zero order production of fines associated with the batch comminution of monosize feeds in tumbling mills has been examined in the context of the size discretized population balance model. It has been shown that the model admits zero order production kinetics only in an approximate sense. The necessary and sufficient conditions for approximate zero order production of fines have been obtained. As these conditions cannot be expressed in terms of the model parameters Sj and Bi,j alone,. several examples have been used to illustrate some of the important characteristics of the zero order production systems. One of the important characteristics of these systems has been identified as a "weak necessary condition", and the other as a " favourable condition ".

Jan 1, 1985

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By D. Malhotra

The effect of some of the reagents, namely hydrocarbon oil, Syntex (sulfated coconut oil surfactant), pine oil, sodium silicate, and lime, used at the Climax mill on the recovery and grade of molybdenite and gangue minerals has been investigated experimentally using factorially designed test approach in the laboratory. The results of the investigation are presented in two dimensional plots. The lower additions of lime (equivalent to a pH of 8 to 8.5) were desirable for maximizing recovery subject to constraints on grade. Higher additions of pine oil improved recovery, but only at the expense of grade. A mathematical model of the objectives of an operating plant was formulated and optimum reagent conditions obtained.

Jan 1, 1977

By H. Y. Sohn

The paper discusses two processes, flash ironmaking technology (FIT) and moving-bed ironmaking technology (MBIT), which aim to reduce energy consumption and greenhouse gas emissions in the ironmaking industry by using concentrate directly without pelletizing and without using coke.

Aug 1, 2023

By Eivind Grøv

"INTRODUCTION Tunneling and underground excavation is related to handling of uncertainties, risks associated with geological conditions are significant and ‘unexpected geological conditions’ often claimed. This fact was brought to the table long ago, and ITA (the International Tunnelling and Underground Space Association) published its 25 Recommendations on Contractual Sharing of Risks in 1988 (Ref. 1). This public-cation constitutes an important asset to the tunneling industry in terms of being a guideline for those working with contractual issues, even today almost 30 years after being published. A more recent document is the ITIG code of practice for risk management of tunnel works from 2015 (Ref. 9). Various countries or geographical regions have their own view and tradition on risk sharing and tunnel contracts. In Scandinavia unit rates contracts are most commonly used with bid-build model, it shares risk between owner and contractor, owner retains the risk for geological conditions while contractor carries risk for performance efficiency. Rock strengthening is determined assessing rock mass quality encountered at tunnel face. Grouting is applied to stem water. Actual quantities may differ from the contract’s BoQ but a flexible contract with remuneration is installed to enable adjustment of actual quantities. Variations of quantities involve a clause to adjust construction time. Unit price contracts deals with expected and foreseen still ‘unexpected geological conditions’, if the ‘unexpected’ element results in variations in quantities. Work activities have quantities and ‘standard capacities’ for regulation of construction time. Variations in quantities are expected in tunnelling and hardly deserve the term ‘unexpected’. If truly unforeseen geological features necessitate work not included in the BoQ, then the contract must be supplemented and can be said to be inappropriate. Fixed price contracts may not provide the intended predictable cost and is as such also inappropriate in the view of a risk sharing principle, once the geological baseline proves to be incorrect. ‘Adjustable fixed price’ contracts, combining unit rate and fixed price, may prove suitable."

Jan 1, 2016

By D. R. Zhu, H. S. Chiang, Y. M. Jiang, S. S. Peng

Two types of underground tests on three types of shield supports, 2-leg, 4-leg, and chock shield, were con- ducted to measure the horizontal movement of the canopy against the immediate roof. In no friction tests, steel rollers were placed between roof and canopy top, while in friction tests normal direct contact was used. Results indicate that the canopy for 2-leg shields always moves forward during setting, whereas there was no forward movement for 4-leg or chock shields. Based on the test results, a model for active horizontal force was proposed.

Jan 1, 1990

By Paul D. Tomlingson

Editor&apos;s note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By K. F. Unrug

Martin County Coal Corp. is located in Martin County, KY, in the Appalachian coal fields, near the West Virginia border. The company&apos;s total leasehold covers more then 133.5 km&apos; (33,000 acres). Total annual production at Martin County Coal Corp. is currently 2.2 Mt (2.5 million st). In certain years, though, it exceeded 2.7 Mt (3 million st). About 45% of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal&apos;s work schedule consists of two nine-hour shifts a day, 240 days a year. Topography The topography of the area is characterized by rugged hills and ridges and sharp V-shaped valleys demonstrating a cliff and slope topography. This topography consists of alternating benches of outcrop sandstone and slopes. The deep valleys have been carved out by many small streams in the area. These streams are contained within the steep slopes of narrow, twisted mountain ridges. The ridges are underlain by massive sandstones that, being resistant to erosion, create sharp, rocky morphology. The height of the hills above the valley floors ranges from 122 to 244 m (400 to 800 ft).

Jan 1, 1991

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By Norman Miskelly

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which include the requirement that a Competent Person prepares and approves publication of mineral resources and reserves. Most national regulatory organizations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organizations, and many dedicated individuals. The historical development of these standards is summarized in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of a Mineral Reserves International Reporting Code Template (International Template) that will be available for all countries to use in deriving their specific country reporting codes, are outlined

Jan 1, 2003

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By Andre Vien, SANDRO DAVID DI, Frank Laroche

In 1994, Claude Bazin presented a novel method for linking size data from milling models to the feed input of flotation models. It was achieved with the simple addition of a metal/mineral distribution–size distribution relationship. This allows grade and recovery predictions from a varying mine plan through product size distribution predictions. 

By Ted M. Noskiewicz, James A. Ramsay

INTRODUCTION During the various stages of an underground project from inception through design and construction, probably the single factor of most interest and concern is the nature of the ground. The ground conditions more than any other item govern costs and feasibility; and although the methods available for assessing the ground have become increasingly reliable during the past thirty years, it is still very difficult in many cases to predict the behaviour of soil and rock during and after excavation. To help in this ground evaluation process, we have frequently supplemented the boring program with one or more large diameter inspection holes; and during the past eighteen years, seventeen of these holes have been constructed on tunnel projects which we have designed. There are references in the literature to similar inspection holes (1); however, as far as we are aware, no detailed description of them has been published. The behaviour of soil or rock during and after excavation and the effect of ground water on tunneling operations are of vital interest to tunnel designers and contractors. A comprehensive geotechnical investigation is therefore among the early and most important tasks carried out on a tunnel project and the backbone of every geotechnical investigation is the boring program. A series of borings, typically 50 to 100 mm (21 to 4 in) diameter, are drilled from which soil samples or rock core are recovered and the ground water observed.

Jan 1, 1979