Search Documents

By Bhaskar B. Thapa

The proposed Caldecott fourth bore will consist of a two lane highway tunnel along California State Route 24 near the City of Oakland. The proposed design and construction sequence for the 15-m-diameter tunnel are based on the New Austrian Tunneling Method (NATM). The initial support system incorporates combinations of shotcrete, rock dowels, lattice girders, spiles, and grouted steel pipe canopies. The final lining is cast-in-place reinforced concrete. A waterproofing membrane and drainage system are placed between the initial and final linings. State Route 24 is a lifeline route, required to be open to emergency vehicles within 72 hours after a major earthquake, defined as having a return period of 1,500 years and a peak ground acceleration of 1.2 g. Although the seismic design criteria are stringent, the design of the tunnel lining system is ultimately controlled by static ground loads in the weak rock along the alignment.

Jan 1, 2008

By Sidney M. Cohen

This paper describes an economical method of upgrading a clay deposit using conventional separation processes into a suitable cement plant feed. The natural size difference of clay and silica in the clay deposit is utilized in the dry air classification device. A case study in which the raw material from a clay deposit is converted into a portland cement plant feed is presented.

Jan 1, 1983

By J. Piper

Markets and Production Beryllium (Be), an extremely light metal, is used in many specialty applications. It the lightest element in Group 2A of the periodic table, with a specific gravity of 1.85 gm/cc, and a high melting point of 12850C (Calvert, 2004). The functional properties of beryllium are stiffness, strength, dimensional stability, resistance to corrosion from acids, and electrical and thermal conductivity. The ability to reflect neutrons and transmit x-rays, makes beryllium irreplaceable in uses such as precision optical components, inertial guidance systems, and in nuclear reactors (Anon, 1993). Beryllium is used in Cu alloys to strengthen and reduce corrosion in copper wire, and in lightweight oxide ceramics that are used as heat sinks, and as electrical insulators. The market revenue of beryllium can be broken down into the seven major groups below, and are plotted on the pie chart in Figure 1 (Anon, 2005). 1.) Telecommunications & Computer 2.) Magnetic & Optical Data Storage 3.) Aerospace and Defense 4.) Automotive Electronics 5.) Industrial Components 6.) Appliance, and 7.) Other.

Jan 1, 2007

By Ruckmick J. C.

Elemental sulphur occurrences are widely distributed in two geological environments: -1-Basins containing hydrocarbons and zones of Cenozoic vulcanism. However, very few of these constitute deposits large enough to be of commercial importance. Almost all of the elemental sulphur mined in the world comes from bioepigenetic deposits in petroliferous basins. These deposits occur in two general structural styles: diapiric (salt domes) and stratiform. Examples of diapiric deposits occur in the Gulf Coast basins of Texas, Louisiana, and southern Mexico. Examples of stratiform deposits occur in the Fergana and Amudarya depressions of Central Asia, the Mesopotamian Depression in Iraq, the Cis-Carpathian Trough in Poland and Russia, and the Permian Basin in Texas. Economic bioepigenetic sulphur deposits range in size from approximately 1 million tons of sulphur in the smaller salt dome deposits to more than ZOO million tons of sulphur at the Mishraq stratiform deposit in Iraq. Total world production from bioepigenetic deposits amounts to approximately 16 million tons of sulphur per year, one-half of the world's present annual consumption of elemental sulphur. Most of the balance of the annual consumption is recovered from sour gas and petroleum. All bioepigenetic sulphur deposits share remarkably similar origins and characteristics. They are formed by anaerobic bacterial replacement of gypsum or anhydrite in tilted basins where evaporite beds are underlain by petroleum. Figure 1 illustrates a generalized cross-section of a salt dome sulphur deposit. Figures Z, 3, and 4 are cross-sections of three types of stratiform sulphur deposits. In terms of sulphur genesis, the only significant difference between the salt dome and stratiform deposits is that the positioning of the anhydrites above the petroleum in the salt domes is caused by diapiric rather than sedimentary processes. In the salt domes, the residual anhydrites of the cap-rocks are accumulated by solution and removal of halite by artesian ground waters.

Jan 1, 1978

By Antoni Kalukiewicz

From 1997 through 2000, a team of Polish experts headed by the author studied the prospects of mining newly discovered emerald deposits in Afghanistan. This article describes the scheme for mechanization of the mining operations, along with improvements made to the ventilation facilities and lighting. The required equipment was flown to Afghanistan and the Afghan miners were trained in machine operation and maintenance.

Jan 1, 2005

By Håkan Tyni, Jan Björkman, Per-Olaf Samskog, Irving Wigdén

Process automation can provide better utilization of capital investments. Furthermore, it is a necessity for securing the high demands of product quality. In this paper, process automation in underground mining as well as in the beneficiation plant will be discussed. The development of reliable broadband communication systems for real-time transfer of image, audio and data have enabled remotely controlled LHDs and drilling rigs. In the beneficiation plants, model-based expert control systems far on-line dynamic process optimization and control have been installed in unit operations such as grinding, flotation and induration.

Jan 1, 2000

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By J. E. Taylor

A detailed planning and design project has been undertaken at Callide Coalfields, as the first step towards implementing a fully integrated mine graphics system. The system, when fully installed, will support applications ranging from business graphics through to terrain modelling and computer-aided design. The conceptual design which will accomplish this is presented. The problems of retrospectively applying graphics standards to existing applications are discussed, and a practical solution outlined.

Jan 1, 1986

By Gerard P. Hand

The use of graphite in industrial applications is one of the oldest in the world. Yet, it is one of the fastest-changing technologies today. Graphite was first used centuries ago in developing writing instruments and as a raw material in crucibles used in melting metal. Today, graphite is used in some of our most demanding industries. These include aerospace, electronics and automotive applications. Graphite usage has historically been split between the natural and synthetic forms. Figure 1 shows the breakdown of natural graphites and synthetic graphites used. The usage of natural graphites and synthetic graphites is split fairly evenly, although the applications are quite different. Figure 2 shows the breakdown of applications using natural graphite. The largest application is the refractory industry. This includes refractory brick and plastics, crucibles, shrouds and other refractory parts. This main application uses roughly 50% of all natural graphite. The refractory industry is an important application for natural graphite. However, the refractory markets have been struggling for several years. As demonstrated in Fig. 3 (Semler, 1996), the production of refractories in tons per year has declined by more than 32% during the last 25 years. Refractory prices have actually risen on a dollar per ton basis during that same period as the product mix has shifted to the value-added side. Raw material and production cost increases, inflation and other related costs have kept profitability at low levels for the industry. Furnace linings that once lasted 1,000-2,000 heats now last 8,000-12,000 heats. This means that tonnage requirements have gone down and quality requirements have gone up for graphite suppliers. Therefore, new opportunities and applications must be developed if the graphite industry is to grow. Synthetics are the other major forms of graphite. There are two forms of synthetic material currently used. One is the traditional type. It is made from the turnings of graphite electrode production. The second was developed in the mid-1970s in response to a shortage of conventional synthetic graphite. This occurred by a breakthrough in thermal technology. This new technology purifies, desulfurizes and graphitizes petroleum coke on a continuous basis at temperatures of more than 2,500° C (4,532° F). This product is called desulfurized petroleum coke (Desulco). It now accounts for about half of the synthetic type material used in the United States. Figure 4 shows the breakdown in the use of synthetic types of material by application. The largest requirement is for use as a carbon addition in iron and steel. This is followed by alkaline batteries and friction materials. Current technological opportunities New opportunities for graphite products are now being developed. These new areas are made possible due to the advances in graphite thermal technology. The ability to purify and modify graphite and carbon products is the key to future growth in the graphite industry. New, higher-purity, more consistent graphite products are leading to enhanced performance in current applications. They are also opening the door to new applications.

Jan 1, 1997

By Mark L. Matthews

In 1978, Congress enacted Public Law 95-604, the "Uranium Mill Tailings Radiation Control Act of 1978." The Act authorizes the Department of Energy to stabilize and control the tailings from designated inactive uranium mill tailings sites in a safe and environmentally acceptable manner. DOE has established the Uranium Mill Tailings Remedial Actions (UMTRA) Project Office to implement, in cooperation with the affected States, Indian tribes and owners of the sites, remedial actions at the sites. The UMTRA Project Office has initiated efforts to perform remedial actions in accordance with EPA cleanup standards.

Jan 1, 1981

By M. H. Dunn, T. P. Danehy, C. F. Denholm, S. L. Busler

The problems associated with abandoned minelands are so extensive that neither federal, state, or local governments nor the mining industry nor watershed groups can adequately address these problems individually. By combining talents and resources, however, these problems are being solved efficiently, effectively, and economically. Utilizing existing water monitoring data, local public-private partnerships have successfully designed and built passive systems within five weeks to six months which treat discharges up to hundreds of gallons per minute that vary in quality from net alkaline to highly acidic, containing as much as 200 mg/L dissolved iron and 70 mg/L dissolved aluminum.

Jan 1, 2002

By Erik Marsh, Frederick C. Harris Jr., Javad Sattarvand, Joshua Dahl, Alireza Kamran Pishhesari

Based on the mine safety and health administration (MSHA)reports, mining truck accidents are among the significant causes of fatalities in the mining industry. The major causes of haulage accidents can be divided into non-driving and driving factors, such as truck-related sudden failures and operator performance. Numerous parameters affect trucks' safe operation, but situational awareness plays a significant role. Due to the distinct structure of mining trucks, making them efficient for mining purposes, the operator has a very limited field of view (FOV), making them prone to accidents resulting in losing lives. The cabin's position blocks the truck's right and rear sides, creating several blind points around it. Aiming to test/train the operator's awareness of the surrounding, a proximity detection system is developed through a multiplayer virtual reality (VR) application to investigate the human factor in equipment collisions. The operators were examined and monitored when asked to conduct what exactly happened in the Marigold mine truck accident without being aware of the scenario. After receiving sound, vibration, and visual alarm warnings, their reaction and performance were analyzed. The platform is developed using the Unity game engine for HTC VIVE virtual reality goggles. An Omni-direction treadmill and a motion simulator platform are utilized for the player and dump truck operators. Fifteen students were monitored when driving the dump truck receiving/not receiving proximity detection alarms. None of them repeated the accident when receiving proximity alarms. Also, they found the visual alarm the most comfortable while driving the truck.

Jun 25, 2023

By M. Y. Fisekci

Subsidence measurement methods, applied over the thick and steep seam mining in the Rocky Mountains Region of Western Canada are described. The studies to date indicate that two new subsidence monitoring techniques appear to be the most suited methods for our conditions. The computerized telemetry and aerial photogrammetry systems are being tested for the reliability of the systems during the winter months within the network of laser surveying over the workings of the new hydraulic mine. The site particulars and the mining method of the concerned area have been described briefly. The observation over the old hydraulic mine indicate that panels adjacent to each other do not obey identical subsidence phenomenon.

Jan 1, 1982

By J. R. Walls

The United States potash industry had its beginning in the early Colonial days. Potash was initially manufactured by leaching of hardwood ashes in large iron pots. Production of potash was recorded as early as 1631 in New Hampshire, and in Maine a few years later. According to the census of 1850, the production of potash was America's most thriving chemical industry and, at that time, 569 plants were reported producing potash from wood ashes. Interest in potash was so great prior to the 1800's that the very first United States patent, signed by George Washing- ton, was granted for the production of potash on July 31, 1790. A new era for the production of potash began when potash was discovered by the analysis from a brine well in 1839 near Stassfurt, Germany while exploring for salt. The predominant use of potash at that time was in the chemical industry rather than agriculture. The discovery, by Justice von Liebig in about 1858, that potash salt contributed greatly to the essential plant food in soil opened up an enormous potential market for a suitable potash material.

Jan 1, 1985

By R. Q. Phillips

INTRODUCTION Since Canada commenced sulphur exports in the early 1960's, the volume of exports has grown steadily and by 1984 Canadian sulphur accounted for 45% of internationally traded sulphur. In 1984 a total of 7.6 million tonnes of Canadian sulphur was shipped to offshore markets and the U.S.A. Total shipments, including domestic sales, were 8.3 million tonnes. With a production of some 5.6 million tonnes, inventory was drawn down by nearly 3 million tonnes in order to keep pace with demand. Since 1979, world consumption has exceeded total world production and Canadian sulphur inventory has played a truly crucial role in balancing world supply and demand. Consequently, by the end of 1984 the Canadian inventory, which stood at 21 million tonnes in 1978, had been almost halved to 12 million tonnes. This inventory, however, is still by far the largest in the world and will continue to play a vital role in the world supply until expected depletion around 1990. Canada is the world's second largest producer of sulphur following the U.S.A.. The Current production level of between 5 and 6 million tonnes per annum is forecast to be maintained to 1990 with only a marginal fall in that production level in the following decade to the year 2000. This will ensure that Canada retains its position as one of the largest producers and most important suppliers of sulphur in the world market well into the future. CANADA AS WORLD SUPPLIER OF SULPHUR Since Canada commenced sulphur exports in the early 19601s, exports have grown steadily. (Figure 1) The rate of growth accelerated in recent years and in 1984 a total of 7.6 million tonnes was sold for export, compared to 3.0 million tonnes in 1975 and less than 1 million tonnes in 1964. World trade in sulphur also increased during this period, from 11 million tonnes in 1975 to 17.0 million tonnes in 1984 (Figure 2). Most of this increase in volume was accounted for by Canada and Poland. As a result, the importance of Canada as world supplier expanded from 28% in 1975 to 45% in 1984. The markets for Canadian sulphur can be divided into two broad categories, i.e., solid and liquid (Figure 3). The solid market is the largest, taking about 70% of Canadian output, virtually all of which is sold offshore. The U.S.A. and the Canadian domestic market take about 20% and 10% respectively, in liquid form. In 1984, (figure 4) total Canadian sulphur sales exceeded 8 million tonnes with offshore export sales at a record 5.8 million tonnes and sales to the U.S. of 1.8 million tonnes. Domestic sales accounted for only 0.7 million tonnes. The general trend for offshore export sales has been upward whereas there has been relative stability in domestic sales. The exceptional growth in offshore sales in the 1970's necessitated considerable capital investments by the industry in order to establish a logistics system capable of handling increasing offshore tonnages. Over 50 sulphur plants are currently operating in Alberta and British Columbia. Some of these are connected by rail, (Figure 5) the balance being generally connected by road. There are currently fourteen of the larger rail-connected plants designated as export plants, and these are equipped with sulphur forming facilities. The long distances between these plants and tidewater terminals in Vancouver is a very significant factor in complex logistics of Canadian offshore sulphur exports (Figure 6). Alberta and B.C. plants are located an average of 1,400 kilometers from tidewater.

Jan 1, 1986

By J. W. Wilson, S. Nakajima, B. D. Singh

According to the Project Independence blueprint, a 270 percent increase in coal production is expected from western coal fields compared to an increase of 100 percent for the nation as a whole. Furthermore, 30 percent of the total United States coal reserves lie in the western states, which are classified as beyond the strippable limits and can be recovered only by underground methods. In view of the fact that the majority of the seams in the West are thicker than those presently mined in other parts of the country, it is important to consider the parameters that relate to mining thick seams and the factors that affect such mining systems. Apart from thick seams, a common feature of many western coal fields is the occurrence of multiple seams that lie in close proximity to one another. These multiple seam deposits present difficult mining problems that have not been encountered to any degree in other U.S. coal fields; for example, ground pressure changes in one mine level caused by mining in the other, sudden water or gas influx from the adjacent levels, the danger of spontaneous combustion in gobs and large and complex subsidence displacements on the surface. Perhaps equally important is the fact that the country can ill afford the present systems of underground mining that attain only 50 to 60 percent coal recovery. With the probability of increased thick seam mining, conservation shall be a focal point in future mine design systems. It is possible that in the future it will be forbidden to adopt the present day wasteful mining methods to ensure that coal can be conserved for future generations.

Jan 1, 1977

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites that contain mineral assemblages derived from the crystallization of post- magmatic fluids or from the metasomatic action of residual peg- matitic fluids. They have been the traditional sources of raw material for ceramic and chemical industries. With the discovery of the Searles Lake deposits, brines became new sources of lithium, and, today, two brine deposits satisfy nearly one-half of the free world demand for lithium chemicals. Indeed, lithium production from pegmatites has been superseded by brines sources. In the United States, the brines of Clayton Valley, NV, have been exploited since 1964 by Cyprus Foote Mineral Company, a subsidiary of Cyprus Minerals Company. In Chile, Sociedad Chilena de Litio Ltda., an affiliate of Cyprus Minerals Company, is now producing lithium carbonate from the brines of the Salar de Atacama. Recently identified brine deposits suggest that these may well become the prime sources of lithium chemicals. In Bolivia, the government is negotiating the rights to exploit the brines of the Salar de Uyuni. The Salar del Hombre Muerto in Argentina is being evaluated as a future center of chemical production. The brines of the Great Salt Lake of Utah, the Smackover Formation, and the Imperial Valley geothermal field have been defined as important resources of lithium. In Tibet, high concentrations of lithium have been reported in several saline lakes. In the People's Republic of China, lithium may be produced from the brines of the Dabusan playa in the Qinghai Basin. The 1950s saw a great number of lithium companies develop. However, following the termination of the Atomic Energy Commission purchase program in 1959, several companies, such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp., were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminumpotlines), the lithium industry grew steadily. With the potential application of lithium metal in batteries, nuclear reactors, and fuel cells, a steady growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Presently identified reserves and production capacity are sufficient to satisfy the conventional market growth of lithium.

Jan 1, 1994

By S. A. Bunk, W. P. Wood

In the early 1980's BHP identified several potential gold deposits in West Africa. One of these deposits was located in Mali, near the village of Syama. As a result of extensive explo­ration activities, an oxide ore as well as an underlying sulphide ore was identified. After agreement with the government of Mali was reached the development of the deposit was undertak­en. The plan for the development of the mine included the treat­ment of the oxide ore followed by the treatment of the underly­ing transition and sulphide ore. The development of the deposit was extremely aggressive. Following the approval of the project in early 1989, engineer­ing was started, equipment purchased sitework was started, and the first ore was introduced in December of 1989. This was accomplished in spite of the difficulties of the site. These diffi­culties included: • remote site location without air or road or water access • no existing infrastructure including water, power, or communication • high health risks • limited construction and manufacturing support in West Africa The operation began with a conventional crushing/grind-ing/CIL/elution and electrowinning facility. The facility was designed to treat 2000 metric tonnes of ore per day. After start­up in December of 1989, the operation was improved to the point that plant throughput was averaging nearly 3000 tpd and running at 92 to 93% availability.

Jan 1, 1996

By Stephen R. Pogorski, Nicholas Busigin, Colin R. Phillips

The movement of radon away from its source in porous media is determined by two key parameters: the fraction of the total radon formed which enters the intergranular pore spaces, termed the emanation coefficient, and the transport processes which exist in these pores such as diffusion and convection. The first parameter, the emanation coefficient, is of primary importance since it is a measure of the actual amount of radon which is free to migrate within the media. The effects of particle size and radium concentration on the emanation coefficient were examined using a quartz-pebble conglomerate ore from the Elliot Lake mining district of Ontario. It was found that the smallest particle size examined (<74 µm) had the highest radium concentration and contributed the most to the radon emanation. A one-to-one correspondence between radium concentrations for the various particle size fractions and radon emanation was not observed. Samples were examined using scanning electron microscopy and very small particulates were observed to be present on the particle surfaces. When these very small particulates were removed from the host particle surfaces by rinsing, the radon emanation decreased by a factor of 17. This result indicates that most of the emanation comes from the very small particles. The effect of moisture on the emanation coefficient was examined qualitatively and a trend of increased radon release with moisture content was noted.

Jan 1, 1981

By George S. Austin

Mud is one of the oldest building materials used by man, but it is not only of historic interest. Even today in many parts of the world, particularly lightly forested areas, it is the chief building material. Many authorities believe that at least 30% and perhaps 50% of the world&apos;s present population lives in earthen dwellings (Dethier, 1985, Coffman et al., 1990). Not all of these people are members of primitive societies or live in third world countries. European, African, Asian, and both North and South American countries contain a large number of such structures. In the United States, the American West, and particularly the Southwest, is known for this type of construction. Some of the earliest remains of adobe structures are those discovered in the ruins of Neolithic farming villages in Mesopo¬tamia dating as far back as 7000 BC (Steen, 1972). The word adobe has its roots in Egyptian hieroglyphs denoting brick and evolved to its present form through Arabic and Spanish (Lumpkins, 1977). The Spanish conquest of the New World spread the use of wooden molds to produce a standard adobe brick. Today, the word adobe is used to describe various earth building materials and techniques, usually referring to sun-dried adobe brick now used in the United States, but is also applied to puddled adobe structures, mud-plastered logs or branches (Jacal or waddle-and-daub), pressed-earth blocks, and rammed-earth walls or pisé (Smith and Austin, 1989, Ferm, 1985). Modern mud construction is used in many countries in various parts of the world. In the United States, the states from Texas to California are perhaps best known for this type of construction. Of these states, New Mexico has the dominant reputation for adobe use. Indeed, in New Mexico the Santa Fe style (Fig. 1) has made adobe not only acceptable, but preferred. RAW MATERIALS Adobe soil used by present day adobe producers, and probably past adobe producers as well, is principally sandy loam (50% clay and silt), although clayey silts are used in some areas (Coffman et al., 1990). In New Mexico, the best adobe soils are those developed on stream deposits, particularly Holocene (Recent) terrace deposits and older, loosely compacted geologic formations, such as the Santa Fe Group (Tertiary) located in the Rio Grande Valley. Some modern adobe producers use a mixture of materials from the screened fines of aggregate operations and mud from irrigation ditches in the river valleys combined with varying amounts of sand to produce the proper blend. Mineralogy Bulk Mineralogy: X-ray diffraction analyses of whole rock samples from many parts of the world where adobe is the dominant construction material show the major constituents of adobe are quartz and feldspar, with lesser amounts (in order of abundance) of calcite, clay minerals, and gypsum (Coffman et al., 1990). Adobes from and climates contain considerable calcite; in some cases calcite is second only to quartz in volume. Quartz, feldspar, most of the clay minerals, and some calcite commonly are derived from the mechanical/chemical breakdown of older rocks units. Some of the clay minerals, much of the calcite and perhaps all of the gypsum are precipitated from evaporating water. Clay Mineralogy: Clay-size minerals consist dominantly of clay minerals, but nearly clay-size fractions contain minor amounts of quartz and calcite, and occasionally other nonclay minerals. In earth construction materials from New Mexico, clay-size particles are the most compositionally variable in commercial adobe soils. However, the clay mineral groups in this size fraction consist of about equal parts of expandable clay minerals (smectite and mixed¬layer illite/smectite or I/S) and non-expandable clay minerals (ka¬olinite, illite, and chlorite), with minor quartz, calcite, and feldspar (Smith and Austin, 1989, Austin, 1990). In the and American Southwest, smectite is commonly calcium-rich and the I/S is dis¬organized and randomly interstratified. In a study of 42 New Mex¬ican commercial adobe soils, only two contained chlorite, and vermiculite, sepiolite, and palygorskite were not found. Soils in temperate climates, as are found in the midwestern and northeastern United States, contain an abundance of illite (Potter et al., 1975). The clay minerals in earthen structures of that region and in Europe commonly contain illite with less amounts of kaolinite, smectite, I/S, chlorite, and vermiculite. In contrast, the clay-size fractions of soils of humid tropical areas are typically acid, with kaolinite as the dominant clay mineral and lesser amounts of I/S, illite, smectite, and others (Chamley, 1989).

Jan 1, 1994