Search Documents

By Thomas M. Tharp, Mark A. Travers

A new method is presented for precracking three-point bending specimens for fracture toughness testing. A notched specimen of rectangular cross section is placed on a flat loading platen, with paper between specimen and platen. The specimen is loaded from above through a roller placed directly over the crack. The thin, high compliance joint between specimen and platen causes a distributed load on the bottom of the specimen. This results in bending at the cracked section and crack initiation at the notch tip. Since the joint is thin, its stiffness increases rapidly with deflection and crack propagation in the specimen generally remains stable and controllable. Fracture toughness KIC in a sandstone directly overlying the No. V coal was measured to be 0.27 MPa m 1/2. Even for cracks 1 cm long this value of KIC results in substantially lower effective tensile strength (modulus of rupture) in roof beams than is expected from intact rock strength.

Jan 1, 1986

By S. C. Sun

[There are significant quantities of anthracite silt deposits in Pennsylvania, known as 'liver silts" (l,2). These contain from 20 to 55 per cent of non-combustible materials, the major portion of these impurities being clay slimes. Both the anthracite coal and impurities are mostly of extremely fine particle size. The utilization of these raw silts in power-plants faces such serious problems as, handling difficulties causing plug-up in equipment, disposal of enormous ash-residue, and corrosion. These problems may be solved by upgrading the raw silt with a cleaning process, which will be capable of removing most of the clay slimes and electrolytes.]

Jan 1, 1964

By Henry O. Ash

On June 16, 1982, Rio Blanco submitted a request to the US Minerals Management Service for a suspension of operations under its federal oil shale lease. The company also wanted a five-year delay in the requirement for further minimum royalty payments and a five-year extension of the primary lease terms of 20 years. The request was granted in late July in the midst of yet another slump in oil shale activity. Rio Blanco holds one of four Federal oil shale leases that were granted under the Interior Department's Prototype Oil Shale Leasing Program in 1974. That year the DOI offered for lease six federal oil shale tracts, two each in Colorado, Utah, and Wyoming. The leases in Colorado and Utah were granted for substantial bo¬nus bids as shown in Table 1, but the Wyoming tracts had no takers. In the eight years hence, no oil shale has been produced commercially. Indeed, the prospects for successful oil shale development have fluctuated widely, continuing a 60-year- old cyclical pattern in the fledgling industry. The prototype program was developed and initiated while this infant industry struggled to begin anew, without the benefit of any federal oil shale leasing regulations, or any history of federal oil shale leasing at all. Permanent regulations were not required because the effort was limited and designed to provide the foundation for any future leasing program. Section 21 of the Mineral Leasing Act of 1920, a Nov. 30,1973 Federal Register notice, and the leases themselves constitute the legal and regulatory framework for leasing and developing prototype oil shale tracts. The prototype leases contain some unusual provisions including installment payments of the bonus bids, credit of early development costs against payments due the government, adjustment of royalty rates according to regional crude oil price fluctuations, and unusually extensive and detailed environmental stipulations. Several of the provisions were intended to provide incentives for early development and financial penalties for failure to develop. The requirement for minimum royalty payments in lieu of actual production royalties beginning in the sixth year of the lease falls in the latter category. After the sixth year, the required minimum payment is increased east year through the 15th year by an increment equal to that due in the sixth year. The minimum royalty then remains the same through the final five years of the primary lease term. Minimum royalty is calculates on a different production level for each prototype lease, based on the quantity of 125 L/t (30 gal/st) shale estimated to be recoverable from. each tract by room-and-pillar mining. That mining system was selected for reference as the only proven extraction method for oil shale at that time (early 1970s) The minimum royalty (production) rate was calculated for each tract by direct comparison of its estimated recoverable 125-L (30-gal) resource to a hypothetical tract containing 1.9 Gt (2.1 billion st) of recoverable 125-L (30-gal) shale. For the hypothetical lease tract, the minimum production for the sixth year was calculated to be 3.2 kt/d (3,500 stpd), increasing by a like amount each lease year through the 15th to a daily production rate of 31.7 kt (35,000 st). Under this formula, the hypothetical lease tract would yield $16 million in minimum royalty payments over the 20-year primary lease term if there were no production, no development credits taken, and no adjustment of the royalty rate due to fluctuation of regional crude oil prices. The production rate of 31.7 kt/d (35,000 stpd) was a somewhat arbitrary figure that was considered, in the early 1970s, to represent a minimum size for a commercial oil shale operation. A production rate of 7.9 dam3/d (50,000 bbls/day) soon supplanted that smaller mine production figure as a rule of thumb for the minimum size for a commercial facility. The proportional relation-

Jan 11, 1982

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

By Donald W. Foss

The Shiloh Church deposit is a very significant molybdenum occurrence in an ususual, perhaps unique, geologic environment. Work done to date indicate that several million tons of "ore" may be present, occurring as a matrix in limestone and dolomite breccias. Mineralized rocks cored to date are at or near the surface and the deeper resource potential has not been tested. The prospect is located in Polk County, north- western Georgia (Fig. 1). The "ore zone" was outlined by North American Exploration, Inc. (NAE) using geochemical prospecting techniques. Extensive geological work, including core drilling, has been conducted on the properties, together with geochemical and geophysical surveys. The geology, geochemistry and geophysics of the prospect are discussed. It is hoped that these data can be used to formulate exploration programs in similar terranes located elsewhere in the eastern U.S.A.

Jan 1, 1983

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By R. K. Simpson, C. S. Eldridge, M. H. Tyler, J. P. Hodgkison

The WMC Olympic Dam Operation in South Australia is an integrated site, involving brown fields exploration through to production of copper cathode, uranium oxide, gold and silver bullion. The Geology and Analytical Services (GAS) Department reflects this totality and, therefore, is perhaps a unique construct in the industry. It comprises Geology, the Metallurgical Laboratory and the Analytical Laboratory, offering a single point of contact in matters of metal discovery and tracking through mine design, production, beneficiation and final product certification. This structure promotes value adding by removing traditional barriers between groups that can deliver more, collectively, than as individual units. This approach to value adding by bringing disparate groups together is echoed in each of the three sections where enhancements in the traditional value adding activities have been delivered by multi-skilling and encouraging overlapping involvement.

Jan 1, 2002

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By P. A. Anderson

Innovative solution management is being used at Coeur-Rochester, Inc. to increase bullion production and decrease overall costs. New operating programs call for reduced solution application rates to the heap to increase pregnant stream values at a lower and less costly plant flowrate because silver and gold extractions are equal regardless of leach solution application rate. Solar heating is used in the summer months to increase the core temperature of the heap for use in the winter months thus increasing silver extraction rate. This paper outlines the programs now in effect and the savings incurred because of them.

Jan 1, 1989

By William W. Leathen

Acid mine drainage became a reality through the exposure of the first bituminous coal seam, either by man or by nature. At first the small amount of acid formed was quickly and efficiently neutralized by basic rock strata and by neutral or alkaline water. As soon as extensive mining operations overtaxed nature's own defensive measures, acid mine drainage became a problem of concern to government and the coal industry. It was the purpose of the studies conducted at Mellon Institute to accumulate knowledge, both applied and fundamental, relating to the formation and disposal of acid mine effluents. It was during this program that the microbiology of acid mine water was studied. Most bituminous coal mine effluents are highly acidic and contain, along with other ions, high concentrations of ferrous iron. The acid is sulfuric, and. the iron is present as the sulfate; both are the oxidation products of iron sulfides (FeS2) which are present in the form of pyrites, marcasites, or other sulfuritic minerals. The oxidation occurs, in the absence of moisture, according to the following reaction: [ ]

Jan 1, 1959

By Robert W. Elayer

For the design of a coal mine and process plant, a comprehensive foundation of geologic information is essential. Historically, the development, collation, and use of this information for design have been costly and time consuming. With the application of a digital computer, however, the effort expended can be reduced and maximum effective use of the geologic information realized. The purpose of this paper is to demonstrate the feasibility and convenience of using a computer to Store and manipulate geologic data for use in mine and process plant design.

Jan 1, 1975

By William H. Dresher

World trade has increased significantly during the last quarter century. However, a new rational for protectionism is emerging which argues for the restriction of trade as a means of preserving and protecting the environment. Fearing lower environmental standards in the Third World, environmentalists are calling for new trade barriers between the developed countries and the developing countries to combat what they see as "eco-dumping." The "greening" of protectionism and the merging of environmental standards into international trade agreements could fundamentally change the world trading system as well as seriously impact the availability of raw materials to provide for the needs of the peoples in both the developing and the developed worlds. This discussion will deal with the agreements and regulations that promise to influence the trans boundary shipment and recycling of scrap metals and wastes containing metals and their projected impact on world trade and metal prices. Emphasis will be placed on the Base1 Convention, whose restrictions concerning trans boundary shipment of scrap metal and metal-containing wastes for recycling took effect on December 31, 1997.

Jan 1, 1998

By William C. Peters

"A large proportion of the earth's surface is blanketed by young sedimentary formations and by recent lava flows. How many Guanajuatos lie concealed beneath the rhyolitic capping of the Sierra Madre of Mexico? How many Kirkland Lakes are under the drift cover of the Canadian Shield? How many Wilunas are still hidden by the alluvium of the desert of Western Australia? How many ore deposits lurk underneath the basalt-covered plateaus of the Columbia River region? If erosion at Goldfield, Nevada, had stopped 100 feet higher, probably no ore would have been exposed. How many Goldfields are still awaiting discovery?" --Hugh Exton McKinstry, 1948

Jan 1, 1969

By Christopher M. St. John, Michael P. Hardy

INTRODUCTION Geotechnical models, particularly those based on the finite element method, have been available to aid in en¬gineering design of underground mining excavations for over ten years. Despite this fact there are remarkably few cases of their use in mine design documented in the literature. It is therefore to be anticipated that many potential users of these models are relatively unaware of their capabilities and limitations and also of the form and detail of geotechnical data needed for their success¬ful application. This subsection attempts to address this problem by discussing the different types of numerical models now available and by noting how some of them have been used to study a variety of problems associated with underground mining. The subsection concludes by discussing the applica¬tion of the displacement discontinuity method to the de¬sign of possible mining systems for the copper-nickel deposits of northeastern Minnesota. The object of the analyses, which were nonsite specific, was to determine the significance of geotechnical parameters, such as ini¬tial stress and rock structure, on the stability of under¬ground excavations and hence to provide guidance for future geotechnical investigation. NUMERICAL MODELS In the geomechanical design of underground mining openings, use is made of numerical models that repre¬sent or simulate the large-scale mechanical behavior of rock. There has been less interest in analysis involving fluid flow and heat transfer, but with increasing interest in such areas as in-situ retorting and solution mining it is likely that there will be a growing need for numerical models embracing and coupling all three physical proc¬esses. However, the emphasis in this subsection will be on mechanical behavior. Models which simulate such behavior will be divided into two groups: continuum models and discontinuum models. These will be dis¬cussed in turn in order that some insight into alternative solution strategies and their merits may be gained. Continuum Models Almost all geomechanical numerical models must be classed as continuum models even though particular computer codes incorporate special provisions for rep¬resenting discontinuities such as faults, bedding planes, or joints. They are continuum models because they pro¬vide solutions for cases where material behavior is governed by the differential equations of continuum mechanics. Two basic solution strategies for such equa¬tions may be identified immediately: the differential ap¬proach and the integral approach. In the differential approach a means of approximating the differential equations over the entire region of interest is sought. In the integral approach use is made of fundamental solutions from continuum mechanics, and these are used to construct a solution to the whole problem, making approximations only on the boundaries of the region of interest. The several differential and integral methods are identified in Table 1. Differential Methods: Problems in continuum me¬chanics involve the solution of three types of partial differential equations. Two of these govern the behavior in so-called initial value problems, in which variables change both in time and in space. Examples of such problems include nonsteady heat transfer and fluid flow, and stress wave propagation. The last type of partial differential equation governs the behavior in boundary value problems. In these, variation is in space but not in time. Solution of initial value problems may be achieved in two significantly different methods: implicit and ex¬plicit. The differences between these two methods will be illustrated by considering a very simple initial value problem, that of one-dimensional heat diffusion. The equation governing this process may be written as: [ ] where T is temperature, K is thermal conductivity, p is density, c is specific heat, t is time, and x is the spacial coordinate. In finite difference form this equation might be written as: [ ] where the superscripts refer to the time and the sub¬scripts to the spacial location. Several solution strategies for this equation have been used. Two important ones may be illustrated very simply by discussing the signifi¬cance of the superscript * on the right-hand side of the equation. If i + 1 is substituted for * then the second derivative of the temperature with respect to distance is evaluated at the end of the next time step (using tem¬peratures not already known). Such an approach leads to a set of equations involving unknown temperatures and a solution procedure which is referred to as being implicit. The important characteristic of the implicit procedure is that it leads to a set of equations that must be solved for each time at which the temperature dis¬tribution is required. If instead of substituting (i + 1) for the superscript *, i is substituted, the following equation is obtained: [ ] {In this case the new temperature is defined in terms of an already known temperature distribution. The solution procedure is now known as explicit and has the impor¬tant characteristic that there are no equations that have to be stored or solved. A practical advantage of this

Jan 1, 1982

By Leo Langland

One of the primary functions of the Geotechnical Services-Materials section of the Arizona Department of Transportation (ADOT) is locating, sampling, and evaluating potential aggregate deposits throughout the State. This information is essential in designing, estimating, and bidding highway construction projects. The nature of materials used for aggregate varies greatly within Arizona. The northeastern or plateau section is famous for its scenic sedimentary formations that are, how- ever, too soft to make suitable aggregate. Volcanic materials are widely used in place of more conventional geologic units. In contrast, the southwestern, or Basin-and-Range section, contains a relative abundance of good aggregate, especially a diversity of gravels. The paper will review the off ice, field, and laboratory methods used by the ADOT Materials Section in satisfying its needs for aggregate information in Arizona.

Jan 1, 1987

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By Jeffrey P. Chanton

A specialized Pore-Fluid Array sampler (PFA) was designed to collect and store pore-fluids to monitor temporal changes of ions and gases in gas hydrate bearing sediments. We tested the hypothesis that pore-fluid chemistry records hydrate formation or decomposition events and reflects local seismic activity. The PFA is a seafloor probe that consists of an interchangeable instrument package that houses OsmoSamplers, long-term pore-fluid samplers; a specialized low-dead volume fluid coupler; and eight sample ports along a 10-meter sediment probe shaft. The PFA was deployed at Mississippi Canyon 118, a Gulf of Mexico hydrate site. A 160-day record was acquired from the overlying water (OLW) and 1.3 meters below seafloor (mbsf). Fluids were measured for dissolved chloride, sulfate, and methane concentrations and dissolved inorganic carbon and methane stable carbon and deuterium isotope ratios. Chloride and sulfate did not change significantly over time, suggesting the absence of gas hydrate formation or decomposition events. Over the temporal record, methane concentrations averaged 4 mM at 1.3 mbsf and was thermogenic in origin (d13C-CH4 = -32.4±3.4?). The timing of an anomalous 14 mM methane spike coincided with a nearby earthquake (Mw=5.8), consistent with the hypothesis that pore-fluid chemistry reflects seismic events. Keywords: Osmosampler, gas hydrate, methane, stable isotopes

Jan 1, 2008

By Stéphane Servant, Jacques Ouellet, Ferri Hassani

This paper presents essentially the logistic and practical aspects involved for in situ testing of mine paste backfill with a self-boring pressuremeter. The investigation discussed in this paper is part of an extensive and ongoing research project to identify and validate an in situ testing technique for cemented mine backfill such as hydraulic or paste backfill as well as Insitu behavior of backfilled stopes. After a literature review on field testing of soils and past experiments on mine backfill in situ testing, the self-boring pressuremeter was selected as the most appropriate instrument for this task. The authors presents in this paper the technical aspect involved in a field trials that was conducted in a Canadian underground mine using paste backfill. The results of this first successful trials show that self-boring pressuremeter test can provide high quality and reliable backfill characteristics results, using analytical techniques developed for soils (Ouellet et al., 1998). The parameters obtained were: estimation of the lateral stress in the ground, the soil stress-strain response and the soil strength. The logistic and equipment required to conduct such testing underground is fully described. Performance achieved in the field and technical difficulties encountered are highlighted. Recommendations for future experiments with such instruments are given. Some potential technical improvements to better adapt this in situ testing technique to mine backfill are proposed.

Jan 1, 2001

By Frank Littlewood

Research over a period of ten years resulted in the development of an efficient automatic ore feed regulator for mill grinding circuits. The facilities that a large mining company gave the inventor made it possible to develop the control apparatus under actual mill operating conditions. The Littlewood Regulator automatically determines the optimum power input at which a mill should operate, and controls the rate of ore feed to maintain this optimum power for any predetermined operating conditions. It is to be noted that the optimum power varies with many factors such as ball, rod, and mill liner wear, therefore the regulator is designed to automaticall keep itself properly calibrated. To efficiently control the rate of ore feed of a mill grinding circuit the regulator analyzes and interprets all power changes of the mill motor. The critical electrical measurements for this type of control are made possible by a patented device that has the ability to detect and integrate minute changes in power. In ball mill operation the small but significant changes in power serve to select the rate of ore feed in accordance with the rate at which ore accumulation takes place within the mill, and in rod mill operation they serve to select the rate of ore feed in accordance with the degree of rod spread.

Jan 1, 1970

By Wm. J. McCracken

HISTORICAL REVIEW OF BOARD OPERATIONS The Ontario Worker's Compensation Board was established in law enacted by the legislature of the Province of Ontario in 1915. It was designed to pay insurance benefits to injured workers, and at the same time to protect employers from legal suit. It was based upon an enquiry system rather than an adversary system such as that used in the courts process. Initially, the system was designed to pay compensation benefits and subsequently, to pay for the cost of medical treatment and pensions for disability and disease resultant from the effects of traumatic injury. In 1947, the Act was changed to include industrial or occupational generated diseases, not specifically related to traumatology. Such occupational diseases were therefore accepted and benefits paid subsequent to that date. As will be discussed in several minutes, even today the vast preponderance of compensation claims with the Ontario Board continues to be related to the effects of trauma. HISTORICAL REVIEW OF EXPOSURE TO RADON GAS DECAY PRODUCTS In some areas of Ontario, especially in Northern Ontario, there is a natural leaching of radon gas from the underlying rock formation. This constitutes very low levels of radon gas decay product radiation exposure to those persons coming in contact and inhaling these substances. This paper however is designed to discuss the occupational generated types of radon gas exposures. For many years dating back to the 1930's, partially refined ores were being shipped from Northern Canada to a refinery located at Port Hope, Ontario, still in operation and currently operated by Eldorado Nuclear Limited of Canada. Initially, the purpose for the operation was extraction of radium to be sold on world markets for medical treatment purposes. With the advent of World War II, this market collapsed. Subsequent to World War II, the availability of other sources of radiation for medical radio-therapy generally replaced the requirements for radium. During World War II, a new market opened up for the Port Hope refinery however as work into nuclear chain reactions and the development of the atomic bomb identified the need for uranium and enriched uranium. During the period of operations where radium was being extracted at the Port Hope refinery, it is now known that an identifiable radon gas hazard did exist. This hazard disappeared when the production line for extraction of radium ceased operations. In 1954, uranium mining operations opened up in Ontario at two locations, Bancroft and Elliot Lake. At the peak of operations, 16 mines were operational and 11,000 workers were employed in these mining operations. A high level of mining activity continued over a 10 year interval with the Bancroft Mines closing permanently in 1964 following a 10 year life of operation. The other mines in Elliot Lake closed about the same time with the exception of two uranium mine operations which have continued to be operational up to the present time. By 1965, due to a dramatic drop in world demand for uranium, the total work force had fallen to 1/10 of the peak work force, and approximately 1,300 workers remained in employment. It is of interest to note that one significant difference in the work environment between Elliot Lake and Bancroft was the high silica content of the Elliot Lake ore. This gave rise to a number of cases of silicosis developing in relatively short intervals of time in the Elliot Lake miner population. No cases of silicosis were identified from the Bancroft operations. Based upon the experience in investigating and evaluating actual cases of lung cancer in the uranium miners over the years, the medical staff at the Ontario Board also developed the impression that radiation levels were much higher in the Bancroft operations, especially in the earlier years of operation, than at Elliot Lake. This resulted in accumulation of higher levels of Working Level Months (WLM), usually over a shorter exposure interval in many of the cases. This aspect will be further evaluated in this presentation. Subsequent to 1965, the work force remained quite static in numbers until 1975. At that time, there began to develop an increase in the work force, and this increase is continuing at a moderate rate up to the present. INITIAL METHOD OF HANDLING LUNG CANCER CLAIMS The first lung cancer claims in Ontario from uranium mining operations were accepted on the perceived cause-effect relationship. This relationship was based upon the data from the Colorado observations and the Czechoslovakia data. Initially, a series of regression equations on mortality were developed and used to estimate the effect of exposure to low cumulative doses of radon daughters as it might relate to the frequency of occurrence of lung cancer at any particular cumulative exposure level. A probability of cancer being radiation induced as against it being caused from other factors was calculated. This method was discontinued subsequent to 1972 due to problems encountered in carrying out this complex evaluation. Thereafter, each case was dealt with on an individual basis, being based upon whether or not the tumour was of the oat cell type, a cumulative exposure in excess of 120 WLM; latency periods in excess of 10 years, commencement of mining prior to

Jan 1, 1981