Search Documents

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

By M. I. Al-Wakeel

Nile sediment was collected as a waste from one of the water treatment plants in Cairo, and subjected to petrographical investigation and granulometric, chemical, and mineralogical analyses. It was expected to find diatomite in that sediment but it was a surprise to find that the diatomite content amounted to about 52.01% by volume in addition to quartz, orthoclase and clay minerals. The latter are represented by montmorillonite and illite minerals. The sediment is light gray in color, soft and has low density and high surface area, such density and surface area generally decrease with temperature. The sediment absorbs 317% of its weight in water. The diatomite skeletons are the main factor responsible for its high porosity producing microporosity and low density, and these particles are concentrated in the very fine silt size fraction (11x2µm). The common diatoms in such sediment include Cyclotella ocellata Pant, and Melosira granulata (Ehr.) Ralfs. It seems that this Nile diatomaceous sediment has many advantages over the fossil diatomite, such as Fayium diatomite in Egypt, with the absence of carbonate minerals that require grinding and calcination those cause destruction of the cellular structure and energy consumption. This Nile diatomaceous sediment can be processed using sequential classification to obtain diatomite concentrate of 88.8% grade at 90.6% recovery, and a middling product of 19.4% grade and 5.8% recovery. The suggested flow sheet is quite simple to produce diatomite product for different industries at a low cost. The unusual particulate structure and chemical inertness make diatomite an ideal mineral to be used as functional filler in a wide range of industries, and as catalyst carriers and insulating material. Key words: Egypt, Nile sediment, Diatomite, Beneficiation, Sedimentation, Classification.

Jan 1, 2008

By Eugene E. Hively

The Tower Kill is a vertical "stirred" ball/pebble mill recently introduced in the Western Hemisphere. This device offers a significant power savings on wet fine grinding applications when compared to conventional tumbling mills. This paper describes the laboratory application of this mill wet grinding hydrated alumina to products of 50 percent passing 2 to 6 microns.

Jan 1, 1983

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By William E. Foreman

The results of the electrokinetic study of the activation of quartz by divalent cations showed that the charge reversal was related to the point at which the cation hydrolyzed. The reversal was not due to the presence of solid hydroxide at the surface of the quartz but due to the charged ions in the solutions. The charge reversal for beryllium at a log molar concentration of 1x10-4 was observed at pH 5 and 9. The quartz was positively charged between a pH reading of 5 to 10. Magnesium at the same log molar concentration did not show a charge reversal from pH 2 to 12. The probable cause of the charge reversal was due to the ionized Be3 (OH)3+3 or Mg (OH)+ . Variations in the electrokinetics of quartz were minimized by heating the sample to 300° C.

Jan 1, 1968

By Jan M. Mutmansky, Y. J. Wang

In the mathematical analysis of electrical networks, the electrical devices are often modeled using idealized network elements such as current sources, voltage sources and resistors. An analogous approach is outlined for the modeling of mine ventilation networks, which can be considered nonlinear resistive networks. The proposed modeling technique uses the following five basic (nonreducible) elements: H, Q, D, R and N. These elements are characterized by their pressure gain or loss, their air quantity and their pressure-vs.-quantity relationships, each of which may be known or unknown. In addition to the definition of the basic elements, the necessary conditions for which there exists a unique solution are discussed. This is performed using theoretical developments derived from electrical circuit theory and illustrated in example networks. The proposed procedures are useful in the solution and characterization of mine-ventilation networks.

Jan 1, 1998

By James J. Fallen

In this paper we are going to look at some things that may happen to the industrial minerals industry in the next decade. First, some concepts and definitions. What are industrial minerals? Not everyone agrees on an answer to this. So let's look at some of the opinions. Some say that industrial minerals are non-metallic minerals. As you well know, metallic minerals are used as a source material for metals. Copper, lead, and zinc are extracted from metallic minerals. But, some metallic minerals are also used for other reasons. Bauxite is used as a source of alumina and aluminum. It is also used as proppant in well drilling, as an abrasive, as a refractory material, and as a source of aluminum-based chemicals. So bauxite is both metallic and nonmetallic. There are other examples, too. Bastnasite is a source of rare earth metals and alloys but its concentrate is used in fluid cracking catalysts. Phosphate rock is an industrial mineral when used for fertilizer, but it is also the source of phosphorus. Ilmenite and rutile are sources for titanium dioxide pigments as well as titanium. So the nonmetallic designation is not adequate to define industrial minerals. Some say industrial minerals are called such because they are consumed in industry. How about your cat's litter box? Is that industry? Huge amounts of montmorillonite, attapulgite and other sorbtive minerals are pelletized and calcined to make animal litter. Doctors are trying to get people to cut down on their salt consumption. They are against people eating industrial minerals. When diamonds are a girl's best friend, they are not industrial minerals; when they are grinding and polishing media, they are. These examples show that industrial minerals are not exclusive to industry. Regardless, here is my list of industrial minerals: Abrasive Materials - Bentonite Antimony (Oxide) - Borates Asbestos - Calcium Carbonate Attapulgite - Diatomite Ball Clay - Dolomite Barite - Feldspar Bauxite (and Alumina) - Fire Clay Fluorspar - Pyrophyllite Fuller's Earth - Rare Earths Graphite - Salt Gypsum - Sand and Gravel Kaolin - Silica Sand Kyanite - Soda Ash Limestone - Sodium Sulfate Magnesite - Spodumene (Lithium) Magnetite - Sulfur Mica - Talc Nepheline Syenite - Titanium Dioxide Perlite - Vermiculite Phosphates - Wollastonite Potash - Zeolites Pumice There is some overlapping. Fuller's Earth takes in some attapulgite, bentonite, and other minerals, depending on the market. Some would like to distinguish industrial minerals by the market emphasis they receive compared to fuels, metallics, and precious metals. But even there, strict logic fails. Some industrial minerals are commodities. They are sold on a price basis against industry product specs, usually in large volumes. Phosphate rock, potash, sulfur, salt, soda ash, and other materials fit this category. Some are almost custom-designed for end-use and meet performance specs. These are sometimes called functional or specialty industrial minerals. Examples of these are ground calcium carbonate, water-washed kaolin, cosmetic grade talc, filtration grades of diatomite, perlite, and vermiculite. To determine prospects for the decade ahead, regardless of our

Jan 8, 1984

By Christopher P. White, John R. Wagner

This paper will discuss the complex and difficult soil conditions encountered in the sinking of 15 shafts of 18m to 27m depth and the excavation and lining of 6700m of 2.74m dia. interceptor sewer on Staten Island, New York. The complex soil profile consists of dense glacial till and sand outwash strata overlying the much older cretaceous sand, silt and clay strata. The tunnel varies from 8m to 14m below the nearby sea level. A significant amount of boulders were anticipated in the till. therefore, a decision was made to excavate the tunnel with a digger shield installing bolted, gasketed concrete segments. The bid documents stated the soils were dewaterable. Several conditions occured in this complex soils matrix which required modifying the planned means and methods including the necessity to use compressed air. The conditions encountered and the equipment used will be described.

Jan 1, 1991

By Paul D. Kovscek, Charles D. Taylor, Edward D. Thimons

When blowing ventilation is used on a mining section, a machine-mounted scrubber is often required to maintain face dust levels below 2 mg/m3. Operation of the scrubber also affects airflow patterns at the face and the dilution of liberated methane. Reductions in scrubber flow can result in increased methane concentrations. During mining, loading of the scrubber filter with dust is likely to reduce airflow. Detecting changes in scrubber flow is difficult, especially with extended cutting, because the machine must be operated from a remote location. Tests were conducted to demonstrate how scrubber airflow could be continuously monitored at a remote location. Three variables, static pressure at the fan inlet, differential pressure across the scrubber filter, and scrubber fan motor current, were continuously monitored while the scrubber filter was incrementally loaded to reduce air flow. The results show that monitoring each variable provided a way for estimating scrubber flow.

Jan 1, 1995

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By Scott Thayer, Michael Murphy, Natalie Cope, Gabriel Esterhuizen, Anthony Iannacchione, Tim Miller, Brent Slaker

"The Subtropolis room-and-pillar mine extracts the Vanport Limestone (Allegheny Formation, Pennsylvanian System) near Petersburg, Ohio. Strata instability problems associated with excessive concentrations of lateral stress caused the mine operator to implement a change in layout design. This mining method has been identified as a stress control layout, which has been used by other underground stone mines in the past with varying degrees of success. Practical experience has shown that entry headings advance in the direction of the principal lateral stress, producing lower stress concentrations with better mining conditions. It is important to minimize stress concentrations along the mining front, so an arrow-shaped advance is recommended. This technique advances more developments (headings) in a “good” direction and reduces developments (crosscuts) in a “bad” direction. As is expected, the stress control layout enhances the potential for shear failures in crosscuts. It is, therefore, important to focus crosscut engineering interventions that either: (a) lower stress concentrations (for example, an arched roof) or (b) enhance strength of the strata containing the shears (for example, rock reinforcement). This study focuses on observing strata conditions on a regular basis and monitoring the response of this strata to changing geologic and mining conditions through 3D Dynamic LiDAR scans.INTRODUCTIONProject AimsThe Subtropolis Mine is extracting the Vanport Limestone in northeastern Ohio. Since the start of mining in 2006, ground conditions have been significantly affected by excessive lateral stress condition. In some other mining districts with this hazard, certain mine layouts have been shown to lessen the potential for unstable ground conditions. The term “lessen” is used to state the realization that stress concentrations are not eliminated but instead occur in less frequency and intensity, and their locations can be projected.The stress-control mine layout, specifically for large-opening room-and-pillar stone mines, naturally evolved at mines suffering from excessive lateral stress problems. These mines will typically experiment with methods to mitigate adverse impacts, thus developing best practices for their conditions. These practices have evolved into a basic framework for the stress control mine layout. For example, Jack Parker was able to write about personal experiences at the White Pine Mine in Michigan (Parker, 1966, 1973). Various researchers at the U.S. Bureau of Mines (USBM), the Mine Safety and Health Administration (MSHA), and the National Institute for Occupational Safety and Health (NIOSH) have studied the effectiveness of stress-control mine layouts over a wide range of geologic conditions (Emery, 1964; Mark and Mucho, 1994; Iannacchione et al., 2003). While the stress control layout design approach has proven successful in many categories, it can be difficult to implement. For example, excessive stress conditions in crosscuts can put the ground control focused intervention at odds with ventilation and haulage constraints, thus limiting optimal crosscut size, shape, and location. Therefore, more information on the effectiveness of this approach is needed."

Jan 1, 2019

By Fathi Habashi

THE MOST important arsenic minerals are shown in Table 6-1. The recovery of arsenic from arsenic sulfides is treated in Chapter Four. Arsenical ores may be either leached directly, or first smelted to volatilize as much arsenic and sulfur as possible, and the resulting product, called speiss, is then leached. A speiss is mainly a complex mixture of metal arsenides, but its [Table 6-1. Arsenic minerals. Arsenides Niccolite NiS Smaltite CoAs2 Skutterudite CoAs3 Sulfarsenides Cobaltite CoAsS Enargite CuaAsS4 Arsenopyrite FeAsS Arsenic sulfides Realgar As4S4 Orpiment As2S3] composition varies widely, depending on the type of ore treated. A speiss usually contains 15-35% arsenic. Methods of leaching are describedd in the following paragraphs.

Jan 1, 1970

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981

By A. Dale Wunderlich

In the past, most people have associated gold scams with the sale of non-existent gold mines, an undivided interest in unmined ore or the sale of gold-plated lead bars. These scams are still available to those who want to speculate. Now, though, the mining industry is plagued with a new type of con artist. Many of the new scams involve large, well established mining companies being victimized. Nearly all legitimate mining companies are in search of good mining prospects. This makes them susceptible to modern day con artists. Many professionals from the mining and petrochemical industries are out of work. Some of them have gotten involved with scams or activities that border on the criminal. Mining companies are losing millions of dollars each year to scams. Some of these scams involve venture-capital fraud. Some involve fraudulent mining proposals. And some involve unqualified individuals who are providing services by the precious metals industry. The author estimates that mining scams may be costing precious metals companies as much in dollar losses annually as employee theft. Employee theft is at an all time high, but so are gold scams. Since January of 1990, the au¬thor has been involved in gold theft investigations in which more than $1 million in gold product has been stolen by employees. In the past, most of the gold mine scam operators have concentrated on the general public, which is generally ignorant of basic mining procedures and practices. A scam artist would tell someone from your neighborhood that they have a wonderful underground mine. It produces 62.2 kg/t (2000 oz per st) of gold ore. Your neighbor might think that sounds like a very good investment. Those involved in the mining industry know better.

Jan 1, 1990

By Stuart R. Cotterill, Jack D. Nelmark

Introduction Opencast surface mining requires blasthole drilling to achieve mine planning. No single method of mining is right for all conditions. Occasionally, mine planners introduce a project with little regard to drilling and blasting. These costs are usually a significant percentage of total mine overhead. One drilling and blasting method that can be used to reduce overall mine expense is inclined or angle hole drilling. But inclined-hole drilling will not cut costs unless a set of required circumstances is met. Several conditions of mine design indicate the use of angle drilling. Geotechnical problems must first be analyzed. Primary considerations are safety, fragmentation, production, and maintenance. Secondary considerations are, in some instances, reduction in amount of explosives, which lowers blasting costs; reduction of practical fragmentation beyond blasting pattern limits; and reductions in overall costs due to reduced volume of excavation. Future trends in blasthole drilling may include incorporation of drill equipment designed to allow rapid change from vertical to inclined drilling. This will allow the operator to adapt to changing hole requirements with minimal production loss. Another improvement may be the ability to chamber holes at any elevation throughout the hole depth. This will allow more charge to be placed at strategic locations to improve fragmentation. Merits of Drilling Inclined Holes Drilling is performed to create voids for explosives. It is done either to recover minerals or to excavate a volume of earth. The manner of mining or excavation can greatly affect the economics of the overall project. Many innovations and methods have been tried, but the most practical and economical is still drilling holes and using explosives to fragment the material. To break up the material, the practice has been to place charges within the mass. This is done by drilling holes of a specific diameter and depth into the material. The holes are of such magnitude as to develop sufficient energy to break or loosen this material, providing for easier removal. In general, more open or exposed faces must exist to aid material breakage when blasting. Inclined drilling can be advantageous in open-cut mining with highwall depths of at least 24 m (80 ft). A minimum of two faces are open in open-cut mining and the material can be thrown outward to cover pre-mined volume. This cuts cost by eliminating the need to remove or relocate a large portion of material. Sometimes the material is of such a mass that more energy per unit is required to loosen it than can easily be done by blasting vertically. Inclined holes allow a more uniform loading of drilled holes. The unit of energy is raised, so little or no secondary blasting is required. This usually comes about only if the main plan calls for drilling holes deeper than 24 m (80 ft). For shallow holes, spacing and burden can be made closer to allow sufficient energy to blast the toe. If the open face is in only one

Jan 9, 1984

By John D. Morgan

The U.S. economy annually needs over 4 billion tons of new mineral supplies. The value of domestically produced energy and processed materials of mineral origin exceeds $175 billion annually, but domestic production of both raw and processed minerals is not keeping pace with demand.

Jan 1, 1974