Search Documents

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By Gregory M. Rumbaugh, Todd Kostecki, Christopher Mark

From 2015 to 2021, five massive pillar collapses occurred at four underground stone mines in the eastern United States. These events resulted in powerful airblasts that damaged mine infrastructure and mobile equipment, seriously injured miners, and disrupted underground travelways. Each of these pillar collapses propagated through the overlying strata, causing a subsidence basin on the surface. Pillar collapses are particularly hazardous for miners because they can occur with little warning and can affect miners that are far from the pillar collapse area. The following case studies show that certain factors may increase the likelihood of a pillar collapse. For instance, each of the five events involved the collapse of at least twelve benched pillars with width-to-height ratios (w/h) of 0.8 or less. This study elaborates on

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By D. E. Cameron

The Cannon mine, located in north-central Washington is mining gold hosted in silicified Eocene-age arkosic sediments arrayed along a regional strike-slip fault system. Branches of the Eagle Creek fault have broken the Chumstick Formation into blocks and wedges, and have caused intense deformation of stratigraphy in the mine. Mineralization at the Cannon mine (B-Reef) and O-Reef (L-O mine) is a bulk silicification with high grade cross-cutting veins containing principally electrum, silver sulfosalts and pyrite in a gangue of quartz, adularia and calcite. Orebodies have very irregular shapes, but tend to follow stratigraphy and high-angle pre-mineral fault breccias and splays developed adjacent to the major faults. Both B-Reef and O-Reef occur at significant bends in the regional trend of major fault strands. Mean gold grades decrease upward from near sea level to the 300 m elevation at the Cannon mine. A new discovery, the A-Reef is hosted by a moderately dipping structure which is at a low angle to bedding. Fluid inclusion studies of B-Reef ore zones indicate dilute ore-bearing fluids boiled at temperatures between 185 and 2850 C at a depth of 1 km. Many ore zones are bounded by sheared mudstone and claystone and a much broader halo of argillic alteration comprising illite, smectite and sericite. Trace and major element analysis by ICP-ES for 33 elements, LECO for S, Hg by CVAA and gold by AA-FA shows dispersion patterns hundreds of meters outward from the known orebodies in the Cannon mine. Geometric mean comparisons, hierarchical R-mode cluster analysis and single element spatial plots show that Hg, As, Sb, S and K/Al compose a suite of elements which are significantly dispersed away from, and increase toward mineralization. Ba, Ca, Na, Mn, V and Zr decrease toward mineralization. The suite is more selective than gold with respect to known mineralization within the exploration area.

Jan 1, 1992

By C. G. Clifton

The Oatman District produced approximately 2.2 x 10 6 ounces of gold and 0.8 x 10 ounces of silver between 1897 and 1942. A total of 3.8 x 10 tons of ore averaging 0.58 O/T gold and 0.17 O/T silver was extracted from eight major orebodies and a number of lesser deposits. Oatman lies at the center of a trachyte-latite-rhyolite volcanic complex which contains at least one resurgent caldera. The orebodies are typical epithermal quartz-calcite + adularia lode deposits which are very deficient in sulfur. Ore deposition has occurred within dilatant zones on faults which radiate from a common point within-the complex. Fischer-Watt Mining approached the Oatman District with an integrated exploration program utilizing four basic procedures to define the characteristics of past productive areas the results of which were applied to unexplored portions of the vein system. These procedures, listed in their order of usefulness, in defining known and prospective mineralized zones are: vein contouring, detailed alteration mapping, fluid inclusion temperature determinations, and geochemical sampling.

Jan 1, 1980

By R. Miller

Lowering our globe’s emissions is a major effort as we move toward a future net-zero carbon environment requiring significant investment in a new, low-carbon infrastructure, along with key market incentives to change. Industry will play a key part in this transformation, requiring expertise in both energy and emissions. Key elements of the de-carbonization strategy are: energy data, emissions reporting method, governance, de-carbonization project generation and drivers, the MACC, electrification, and the de-carbonization checklist. For a zero carbon future, it will be key for business leaders to understand decarbonization, anticipate technological changes, and implement new business me

Mar 2, 2022

By J. R. Patts, A. B. Cecala

"After industrial sand has been mined and processed, the finished product is typically loaded into small bags of 45 kg (100 lb) or less, large bulk bags of 454 to 1,361 kg (1,000 to 3,000 lb), or vehicles such as trucks or trains for transport to end users. As the sand is being transferred and loaded, dust can be released into the work environment, potentially exposing workers to respirable crystalline silica. A number of control technologies have been developed and utilized in an effort to reduce dust liberation during loading operations. For bulk loading into trucks or trains, the U.S. National Institute for Occupational Safety and Health (NIOSH) evaluated one of these technologies, the Dust Suppression Hopper (DSH), at two industrial sand processing plants. Results from these case studies show that the DSH reduced airborne respirable dust levels by 39 to 88 percent, depending upon the product size being loaded.IntroductionInhalation of respirable crystalline silica dust can lead to the development of silicosis, a disabling and potentially fatal lung disease. Once contracted, there is no cure for silicosis, so the goal is to prevent the development of the disease by limiting exposure to respirable dust containing crystalline silica at or below the exposure limit of 50 µg/ m3 recommended by the U.S. National Institute for Occupational Safety and Health (NIOSH, 2002). At industrial silica sand operations, the product contains high levels of crystalline silica, so effective control technologies are needed to minimize the respirable dust exposure of workers.NIOSH, in partnership with the Industrial Minerals Association–North America, published a dust control handbook (NIOSH, 2012) focused upon control technologies for industrial- mineral mining and processing operations. One chapter in this handbook discussed technologies for controlling dust liberated during bulk loading, including telescoping loading spouts, dust collection systems for loading spouts, enclosures for load-out areas and a newer technology known as Dust Suppression Hopper (DSH)."

Jan 9, 2018

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By B. A. Barnum

The Chino mine is an open pit copper mine located in southwestern New Mexico, at an elevation of 1890 m (6200 feet) above sea level, approximately 117 km (70 miles) north of the Mexican border. It is owned by Chino Mines Co., a Phelps Dodge Corporation-Mitsubishi Minerals partnership, and is operated by Phelps Dodge Corporation. As part of an effort to maximize production and minimize costs, a computerized truck dispatching system was approved for purchase and installation at the Chino mine in March. 1984. Modular Mining Systems, Inc. was commissioned to install their system, trade named DISPATCH. The system installation was completed and operation began in July, 1985. Installation and operation of the system has presented some interesting challenges and problems, which have been overcome, resulting in increased productivity for the haulage truck and shovel fleets.

Jan 1, 1987

By Art Hamid, Manfred Wong, R. John Caulfield

"The proposed Channel Tunnel is a critical component of the San Francisco Public Utilities Commission’s (SFPUC) Central Bayside System Improvements Project (CBSIP), which is a key element of a $6.9-billion sewer system improvement program to upgrade its aging and seismically vulnerable wastewater facilities. The tunnel will provide gravity conveyance and storage of combined sewage flows from the northeast sector of San Francisco, CA to the Southeast Water Pollution Control Plant for treatment. The tunnel will be approximately 2.7 km (1.7 miles) long and 7.3 m (24 ft) in internal diameter. It will utilize a single-pass precast concrete segmental lining system. Tunneling challenges include excavating with pressurized face tunnel boring machine (TBM) technology through highly variable ground conditions including the Franciscan Complex (rock and mélange), clayey/silty sands, stiff to hard clay (Old Bay Clay) and mixed-face conditions. The project will also require several deep shafts that will be technically challenging. Project backgroundThe SFPUC is a department of the City and County of San Francisco, CA that provides municipal power, drinking water and wastewater services to San Francisco.San Francisco’s combined sewer system collects both wastewater and stormwater in the same sewers, which is then pumped, treated to stringent state standards and discharged into the San Francisco Bay and Pacific Ocean. The sewer system includes tunnels, large storage/transport boxes, 1,600 km (1,000 miles) of collection sewers, 28 pump stations and three wastewater treatment plants. After decades of service, much of the system is nearing the end of its useful life.The existing system is also vulnerable to seismic damage. During the 1989 Loma Prieta earthquake, damage to SFPUC wastewater infrastructure was extensive. This included the 3,415 m (11,200-ft) long, 1.7m (66-in.) diameter Channel Force Main, built in 1976, and a critical component of the conveyance system. The Channel Force Main carries 70 percent of the bayside dry weather sewage flow from the northern and central part of the city to the Southeast Water Pollution Control Plant for treatment. It is antiquated, not pile-supported and not constructed to current seismic codes. There is also currently no conveyance redundancy for north/central bayside flows to the treatment plant. Figure 1 shows the SFPUC’s wastewater collection system, the existing Channel Force Main and the project location."

Jan 5, 2017

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By Keith Whitworth

The USSR, over the last 20 years, has continued to increase its out-put year by year and it is now almost four times what it was at the end of the Second World War. In 1975, it exceeded 700 million tons of run-oi-mine coal (all ranks) which amounts to over 20 percent of world output. This rapid progress has been due to modernization of the industry, by means of increased mechanization and automation and the development of new machines and systems for underground workings and by the expansion of open-pit workings and the development and implementation of larger earthmoving machines.

Jan 1, 1977

By J. E. Feddock

To succeed in today's competitive coal market, coal companies must continuously improve production and lower cost. However, the coal industry's historical management practices must change to remain viable? The practices of the current day efficient coal mine manager are reviewed and examined using W. Edwards Deming's definition of management. The statistical tools, including Pareto Charts, Control Charts and Scatter Diagrams, which identify the problems management must approach differently to increase productivity at a coal mine, are discussed.

Jan 1, 1993

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By E. E. Maurer

Kerr-McGee has operated the Ambrosia Lake uranium mill since startup in 1958. Tonnage milled per day has varied from 3500-7000 tons. The mill capacity is currently rated at 7000 tons per day. The process consists of two parallel circuits following crushing and sampling, \\lhich include open circuit rod mill grinding, sulfuric acid leach, cyclone classification, and counter-current washing circuits of sand classifiers and slime thickeners. Pregnant solution is clarified and polished by precoat pressure leaf filters prior to amine solvent extraction. Yellowcake is precipitated from the pregnant strip solution with ammonia, filtered and dried.

Jan 1, 1972

By J. W. Butwell

Anaconda has been active In the Bingham mining district near Tooele, Utah since 1914 when the company acquired International Smelting & Refining Co. Over the years both custom ores and complex Pb-Zn-Cu ores from the district were milled and smelted at International. In 1948 Anaconda acquired the property that covers the present Carr Fork ore body. Since that time active exploration took place in the 50's followed by detailed geological evaluation in the 60's. Convinced that high grade Cu deposits would be found at depth, a deep drilling program commenced in the late 60?s, with intersection of the ore zone in 1969. Following extensive deep drilling in the early 70?s, a feasibility study was conducted in 73-74 with board approval given Sept. 6, 1974. The 9,000 t/d mine-mill complex was budgeted at $217 MM over a 5 year schedule with start-up in Sept., 1979. The following discussion includes the concentrator and surface facility portion of the budget or approximately $60 MM of the scope. Special emphasis will be made on equipment selection and layout.

Jan 1, 1980

Paper and paperboard manufacturers need to quantify the carbon footprint and environmental impact of their products to satisfy market, social and government demands. Coated paper products contain minerals, such as kaolin and calcium carbonate, at significant levels; some coated paper grades have mineral contents as high as 45% by weight. Some uncoated paper has no mineral content, but most uncoated paper contains some mineral to improve appearance, process efficiency and cost. Super-calendared paper grades can contain levels of mineral up to 35% by weight. This paper describes how to calculate the carbon footprint of kaolin and calcium carbonate minerals used for white pigments. The carbon footprint of these minerals strongly correlates to the primary energy sources, final product form and energy used to calcine kaolin and lime. Kaolin and calcium carbonate pigments have a favorable impact on the carbon footprint of paper and paperboard products by directly substituting for fiber and by reducing the energy needed for paper making. Key words: Kaolin, Calcium carbonate, Paper production, Carbon footprint, Lifecycle analysis

Jan 1, 2010

By Megan Badonie, Devlon Shaver, Evan J. Owen, Virginia T. McLemore, Jakob Newcomer

Critical minerals are becoming more important in our technological society because they are used in many of our electronic devices, batteries, and magnets. In New Mexico, low to moderate concentrations of critical minerals are found in Late Cretaceous coal and related strata in the San Juan and Raton Basins. These rocks are being characterized as part of the DOE’s CORE-CM (Carbon Ore, REE, and Critical Minerals) program. The New Mexico coal, humate, and clinker deposits are relatively low in REE (<325 ppm TREE), Li (<90 ppm), V (<168 ppm), Co (<51 ppm), Ni (<108 ppm), Zr (<557 ppm), and many other critical minerals compared to normal economic deposits. Some of these rocks are enriched in Al2O3 (<40%) and Sr (<3740 ppm), both critical minerals. Common minerals hosting the critical minerals in these rocks include clay minerals, zircon, and rutile/anatase. As the demand for some of these elements increases because of increased need and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Ultimately, economic potential will most likely depend upon production of more than one commodity, maybe even from coal, humate, and clinker deposits.

Feb 1, 2024

By Bo R. Arvidson

The strongest magnetic roll separator available on the market enhances certain industrial minerals purity to levels not reached previously. Exceptionally strong forces can also be utilized for processing relatively fine particles at feed rates several times greater than for prior art electromagnetic induced roll separators. Since the unique machine does not work with an air-gap, coarser particles than what has been considered practical can be separated at rates up to 20 tph per single machine unit and 40 tph for a double machine unit. Examples for all these three application areas will be given. While the roll separator can be used only for dry processing presently, the other new separator can be used for both wet and dry applications. It is a medium-intensity, high- gradient magnetic separator employing a filamentary matrix. It was primarily developed for recovery of weakly magnetic iron ore fines, but it is finding applications for cleaning of industrial minerals such as wollastonite, calcite, clay and talc. Its main advantage is a simple design resulting in a very lm cost machine both with regards to total capital investment and operation. A significant technical advantage exists also. The metallurgical performance is similar to conventional electromagnetic separators, while the cost per ton is about half of such separators.

Jan 1, 1985