Search Documents

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein, and the other the Koerner vein, which lay about 1100 feet to the south, This vein system has been explored and mined over 9000 feet horizontally and 4800 vertically. In 1950 continued exploration led to the discovery and subsequent development of replacement ore bodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma Mine, and follow the strike and the 30" east dip of the host limestone. Strike length of the ore bodies varies from 250 to 500 ft., and thickness from 15 to 125 ft. The ore bodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is charactertistic of substantial portions of the replacement beds. In many instances the ore itself is blocky, badly fractured, and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 1, 1973

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By A. Rai

"This paper provides an overview of the current use of auxiliary ventilation product and the challenges with limited air quantity in dead-end entry or working face. The PVC low frictional factor, low physical constraint and minimum leakage ventilation duct was development with ""made in US and used in US"". The PVC duct development covering operational and total cost of ownership with on-going success will be presented. This paper will discuss mine sites using new PVC vent duct underground and the results from operational and technical side making a difference. INTRODUCTION The Turquoise Ridge Joint Venture (TRJV) is located in northern central Nevada, and is situated within the Basin and Range province, near the northeast end of the Osgood Mountains (see Figure 1). The TRJV mine consists of typical Carlin type- gold mineralization characterized by low strength rock of altered limestone’s, siltstones, and mudstones. The weak nature of the ground facilitates the underhand cut and fill mining methods [3].Mining Method; Underhand cut and fill : The mine uses underhand cut and fill method which has 12’x12’ top cuts and several different size undercuts. The ore body is accessed off of a secondary development heading, utilizing a heading with a cross section of 14W x 14H or 15W x 16H configuration. In the wider and more massive zones, two headings in a production panel may be worked at any one time. Drift round lengths are determined by the type of drilling machine being used. An example of a typical topcut and associated undercut layout is shown in Figure 2. SECONDARY / AUXILIARY VENTILATION IN UNUNDERGROUND METAL MINES The auxiliary ventilation system provides the required air volumes at the face of dead-end developments and production workings, which in many cases may be considered as the primary method of assuring that the air quantity and quality standards in these working areas are satisfied. The Auxiliary fans and ducting systems are usually the primary means of delivering the required air volumes to the face of dead-end developments and production workings. Both centrifugal and axial-flow fans are used in underground auxiliary ventilation systems, usually electric powered. The internally direct driven axial-flow fans tend to be more popular because of their compactness and adaptability to staging. The most commonly used materials for ridged tubing are coated steel, alloyed steel, fiberglass and resin. Flexible (collapsible) ventilation tubing is also used and is usually made from neoprene-coated or nylon material. To add stiffness and reduce collapsibility these fabric ducts can be formed over a steel spring frame. A very important factor in the design of an auxiliary ventilation system is to minimize leakage and reduce the frictional pressure losses along the auxiliary ducting systems by minimizing their friction factors (K)."

Jan 1, 2015

By F. Habashi

The peninsula that lies between the Black and Mediterranean seas, called Asia Minor by the Romans and Anatolia by the Greeks, was one of the crossroads of ancient civilizations. The fall of Constantinople in 1453 was a turning point in the history of mankind. Visits to Istanbul, Ankara, Eskisehir, Cappadocia, and Trabzon will be given together with the history of the country. Mineral resources of the country will also be briefly outlined.

Feb 23, 2014

By P. C. Dagneau

QUEBEC CARTIER MINING COMPANY was incorporated in 1957 to explore and develop low grade iron are deposits in Northeastern Quebec. Four separate deposits were located and identified as being of ore quality and size to support commercial development. Said deposits were located at Lac Jeannine, Mount-Wright, Fire Lake and Mount-Reed. In 1970, in preparation for the replacement of the depleting Lac Jeannine are reserves, construction of an SS-mile railway extension was initiated, towards the newly selected mine site at Mount-Wright. This orebody was selected because the physical and chemical characteristics of the ore were very much similar to those of Lac Jeannine, as well as its huge reserves, estimated at more than one billion tons. In addition to the railroad extension, a mine, concentrator and related facilities were constructed and the new town of Fermont was created. Total investment for the Mount-Wright project exceeded $700 million and initial production commenced in 1976. Quebec Cartier is presently (1992) the leading producer and seller of iron ore in North America at 15,5 million tons and employs some 2,300 people.

Jan 1, 1993

By Brian Young, Ben Pantony

Interferometric Synthetic Aperture Radar (InSAR) has played an integral role in many large scale tunneling projects globally. Until recently, it has been regarded as a complementary monitoring tool. On the Los Angeles Metro Purple Line Phase 1, InSAR was proposed as a primary means to replace weekly and bi-weekly surface monitoring requirements on surrounding critical infrastructure. This paper will summarize the statistical analysis approach engaged in order to compare and contrast a year of historical InSAR data to known geodetic survey data, in order to utilize InSAR as an operational monitoring tool on this project.

Jun 13, 2021

By M. K. Larson

"Specialized numerical modeling codes have been developed over the years to estimate ground stresses during the excavation of coal in underground mines. One of these tools, MULSIM, a displacement discontinuity boundary element code, was last developed by Zipf into a version called MULSIM/NL [USBM 1992a, 1992b]. The code was used frequently in years past, but closure of the Bureau of Mines in 1996 marked the beginning of a pause in its development. A similar tool with distinctly different treatment of overburden idealization, LaModel, was subsequently developed [Heasley 1997] and largely displaced MULSIM/NL in the literature. However, recent work modeling deep western longwall coal mines [Larson and Whyatt 2013] has demonstrated that MULSIM has distinct advantages for regions with relatively stiff and strong overburden. This work required that MULSIM be revived and updated into a version called MulsimNL/Large. Updates include larger array sizes, greater precision, greater number of materials, and the addition of a five-point, six-segment pillar load/displacement model that provides the user a more flexible coal-strength model allowing hardening and softening before a final residual strength. MulsimNL/Large has the ability to calibrate to large load transfer distances observed in some western U.S. coal mines that appear to be caused by strong, massive units in the overburden and/or floor of a coal mine. Also, it provides the ability to calibrate gob stiffness to simulate measurements or estimates of overpanel weight distribution between gob and abutment, while still maintaining load transfer distance with minor adjustments. MulsimNL/Large can easily implement material strengths calculated from various pillar strength models. The five-point model gives MulsimNL/Large the ability to easily simulate pillar behavior that is extracted from detailed pillar models, such as FLAC3D. MulsimNL/Large or similar approaches should be considered for evaluating mining layouts where stratigraphic conditions are known to cause overpanel weight to transfer to an extent significantly longer than the empirical method widely used to calculate load transfer distances in the U.S. [Peng and Chiang 1984; Mark 1987; USBM 1990]."

Jan 1, 2015

By H. F. Haller

Large volume sand plugs are placed in tunnels to stem underground explosions at the Atomic Energy Commision's Nevada Test Site. Placement through long, narrow accessways is like stemming coyote holes and blast chambers in mining and construction. Experience with several other methods showed that pipeline conveying could be preferable. Small scale tests justified predicting a placement rate of 20 y. p. h. at 1000 feet, with a modified gunite placer. The initial production trial placed over 2000 c. y. and was estimated to effect a small cost saving after paying for new equipment. Initial problems included duct replacement and supply delays, dust, and other personnel hazards. Operations analysis and SOP'S reduced delays during the second field trial, minimized hazards, doubled production. Re cent re search and operations analyses produced data on abrasion resistant ducts, identified minor equipment modifications which can improve production, developed techniques for impact compaction to 90% ?maximum? and for extension of the practical range to 2000 feet. Twenty-two illustrations include an air consumption-distance chart.

Jan 1, 1967

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By B. A. Hancock

New permit discharge standards instituted at Hecla Limited?s Lucky Friday Mine required installation of water treatment plants to manage water quality at two outfalls to the South Fork of the Coeur d?Alene River. The 002 Outfall Water Treatment Plant (WTP) is a clarification-filtration plant for treating the combined mill and underground discharge water flows. Process optimization efforts were a significant challenge until the negative impact the exploration diamond drilling products had on the clarification process was identified and resolved. The products were being wasted directly to the mine water discharge system which was pumped to the surface WTP. Anionic soluble oil and polyacrylamide based products were causing TSS particle hydrophobicity and dispersion that greatly affected coagulation and flocculation response, resulting in excessive chemical usage and treatment control issues. This paper details how problems associated with the drill products negatively impacted the 002 WTP and how system changes, alternative product usage and treatment at the source resulted in more consistent plant performance.

Jan 1, 2011

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

By Thomas H. Dubaniewicz

(XP) enclosures to enclose electrical ignition sources to prevent propagation of an internal methane-air explosion to a surrounding explosive atmosphere. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a lithium-ion battery thermal runaway test within a modified MSHA-approved XP enclosure to assess thermal runaway containment. Thermal runaway produced jet flames emanating from the cover joint at several locations and distorted the cover joint and bottom plate of the enclosure beyond allowable limits. The test demonstrates that XP enclosures may not provide adequate explosion protection against lithium-ion battery thermal runaway. This paper suggests some approaches to mitigate the hazard.

Feb 1, 2024

By Andrew J. Petruska, Austin F. Oltmanns

This work proposes a capacitive load cell for conical picks to enable underground continuous mining machine operators to perform their roles away from known hazardous regions near the machine. The load cell is embedded in commercially available flexible printed circuit board, integrates with the target tooling, and demonstrates in situ force sensing of vibration signatures for continuous mining cutting tools. Changes in material constitution, tool mass, and tool geometry cause modal variations in vibrational response measurable with force sensors at the cutting interface. Time-series measurements are captured during rock cutting tests using a linear cutting machine. These measurements are segmented into small windows, less than 0.25 s, and are preprocessed using the fast Fourier transform, which highlights the modal variations. The transformed measurements are then classified into different material and wear categories using support-vector machines with the radial basis function kernel. Different normalization schemes and Fourier transform methods are tested for signal preprocessing. Results show that the power spectral density measurements with normally distributed coefficients give good results for material classification, while the normalized time-domain measurements give better results for wear classification. Under laboratory conditions, this technique is shown to classify material and wear categories with F1 score above 0.85 out of 1.0 for our experiment. This technology could be used to assist operators in assessing material and wear conditions from a safer distance. It has applications in the coal mining industry as well as other applications which use conical picks such as road milling.

Mar 25, 2023

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

By Angelina Anani, Nilufer K. B. Akbulut, Sefiu O. Adewuyi

Crucial information about safety, design, and operation can be utilized in underground mines from ground movement data. Communicating the information and exploring new findings can be a challenge in a decade where there is an ever-increasing volume and velocity of data due to advancements in mining technologies. This challenge escalates for geotechnical data as it is multidimensional, depending on the space and the rate it takes place. To tackle this challenge, geotechnical engineers should focus on utilizing simple yet compelling visualization of rock mass data in 3D. Competent visualizations of ground conditions as a Trigger Action and Response Plan (TARP) could ease the communication of safety concerns and the exploration of rock mass displacement and strain surrounding an opening at an underground mine. Therefore, this study focuses on using scientific visualization methods by rendering geotechnical data over the surface of a 3D mesh model to display TARP levels. The study is conducted at the San Xavier (SX) Underground Mine Laboratory’s East decline. The project aims to produce visualizations that optimize the use of geotechnical data in near-real-time.

Feb 1, 2025

By James K. Gowans

Polaris Mine, a Cominco Ltd. property located on Little Cornwallis Island, Northwest Territories, Canada, (Lat. 75°30'), is the world's most northerly base metal mine. Polaris Mine, which commenced operations in late 1981, is characterized by its unique process barge. The lead/zinc concentrator, powerhouse, shops, offices, dry and warehouse have all been incorporated on a 400 ft. long by 100 ft wide by 65 ft high barge. This process barge was constructed in Southern Canada, at Trois Rivieres, Quebec, then towed 3500 miles into its final resting place on the high arctic. This paper describes the unique design of the barge concentrator and deals with the start-up and continuing operation of the Polaris Concentrator.

Jan 1, 1984

By Peter Dietrich, Joseph DeMello, Norbert Fuegenschuh, Kerwin Hirro, Jeff Brandt, Mike Cole

This paper presents a successful case history of the ground improvement efforts and excavation of twenty-three cross passages between twin bore tunnels driven by EPB tunneling machines in Los Angeles, California on Section 1 of the Westside Subway Extension. Unique and complicated ground conditions local to the tunnel alignment include San Pedro sands, siltstone/claystone Fernando Formation, and zones of “asphalt impacted soils.” To provide water cut-off and soil stabilization, jet grouting was performed prior to TBM excavation at the location of many of the cross passages. However, upon investigating the cross passages prior to excavation, the subsurface conditions required additional measures and SEM tools to ensure successful completion of the project.

Jun 13, 2023

By Robert Bissonette, Samir Sbai

A critical component of implementing autonomous systems is the ability to use information from a robust sensory and information system to make sound, predictable, and repeatable decisions to assure safety. This means that any such system would need to evaluate what objects (people, equipment, boulders, etc.) of interest exist in that environment (with relevant data about identity, trajectory, characteristics, etc.), project a future continuum of those objects (including considerations for variabilities), and make control intervention choices to minimize risk due to exposures in the present operational area. The components of an overall system would include: a) sensor and data fusion, b) probability projection of future states, c) generation and evaluation of alternate futures, and d) implementation of best course of action to reduce risk. The National Institute for Occupational Safety and Health (NIOSH) Spokane Mining Research Division (SMRD) is studying this framework for applications for autonomous mining equipment. This paper focuses on using information from the sensor fusion engine to generate a continuous projection of future and alternate states (b and c above) incorporating the factors of confidence, accuracy, tolerance, and other variabilities. We refer to this as Machine Situational Awareness (MSA).

Jun 25, 2023