Search Documents

By A. Bleier, E. D. Goddard, R. D. Kulkarni

The influence of the collector structure on the amine (RNH2, R=alkyl) flotation of quartz has been systematically investigated using a modified Hallimond microflotation cell. This study focuses on the effect of varying chain length, branching in the alkyl group R, polyfunctionality of the collector molecule, and alkyl substitution on the nitrogen atom. In addition, adsorption at the solution/air interface and electrokinetic results for the solid/solution interface were employed to further elucidate the role and the interrelation of the structural parameters in the flotation process. Estimates of an electrical double layer attractive energy between the bubble and the solid particle are made.

Jan 1, 1976

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By E. W. Cokayne

GENERAL DESCRIPTION OF THE METHOD The original application of sublevel caving was in ground so weak that it would collapse even in small headings when the support was removed. Heavily tim¬bered drifts were driven across the ore body; the timber was removed at the end of the drift, and the ore caved and slushed out. When dilution became excessive the next set was removed and so on. This method gave high dilution and poor recovery and was slow, but it was the only way to mine this type of ore body at that time. In more recent times the method has been adapted to stronger ground which needs to be drilled and blasted, so it is not a caving method as far as the ore is con¬cerned. However, the method does rely on the walls to cave and so the name sublevel caving has been retained. The method as presently generally applied is shown in Figs. 1, 2, and 3. Sublevels are established at approximately 7.6 to 12.2-m (25 to 40-ft) vertical intervals. They are usually accessed from a ramp system. A haulage drift is driven down the strike of the ore body, but in the waste. Production drifts are turned off the haulage drift and driven across the ore body on about 10.7-m (35-ft) horizontal centers. This divides the ore body into a geometrical pattern. Slot raises are driven at the end of the drifts near the ore-waste contact and the slot is expanded to the shape of the fan drilling. Up holes are drilled to break towards the slot at burdens of 1.2 to 1.8 m (4 to 6 ft). They are drilled past the next sublevel to the production drift im¬mediately above. When a sufficient number of fans has been drilled, production can start by blasting one or two fans at a time towards the slot. Load-haul-dump (LHD) units are used to muck the ore, which rills out into the drift. At first, when only a small area is mined, the walls may not cave, and the operation will be similar to open stoping. Later, sloughing from the walls will fill any voids created, and the ore after blasting will be con¬tained by the caved waste and gravitate downwards as mucking proceeds. This process is repeated in each of the production drifts as the face is retreated towards the haulage drift. When the top level has been retreated back a safe dis

Jan 1, 1982

By Malcolm J. McPherson

This paper describes the algorithm used in a BASIC program for an IBMXT microcomputer, to simulate the underground mine climate. The program called CLIMSIM has been developed and refined over several years as a result of considerable use at operating mines. The program has been designed to be easy to use and be understood by the practicing mine ventilation engineer. It provides predictions of the work place climate, so that the optimum ventilation/cooling system can be designed to obtain a certain air cooling power or effective temperature at the work place. An example is given of the application of the program to a mechanized cut and fill stope at the Homestake gold mine in South Dakota.

Jan 1, 1986

By C. Cassios

EIA is a procedure aiming the elimination of adverse impacts to the environment from undertaken projects. Historically, it starts in 1969 when NEPA (Nat.Env.Prot.Agency) in the US initiated the EIA ? EIStatement. The EIA procedure was adapted by the European Union with the directive 337/85 and in Greece the Common Ministerial Decision 69269/90 enforced it to the Greek legislation. However, mining enterprises in Greece long before the implementation of the European Directive and in accordance to the legislation of the Public Law 998/79 for the protection of the forested lands were obliged to submit EIA?s and get an approval in order to operate in forested areas. The submitted and approved EIA?s and their implementation by the mining companies were among the positive aspects of the EIA procedures. This paper is examining the impacts of EIA?s in the Greek mining industry its positive aspects as well as their difficulties and their role for the reclamation procedure. The technical and procedural aspects which EIA presents for the mining industry are commented, while proposals, for a more flexible EIA implementation for the Greek Environment are also presented.

Jan 1, 2002

By M. O?Driscoll

The tide has turned. Developments in China that have continued to unfold over the last four years or so have now reached a point where the supply market dynamics of certain industrial minerals have changed significantly. No more is this sea change better exemplified than by the supply market for magnesite, and in particular, its processed derivative grades of dead burned magnesia (DBM), caustic calcined magnesia (CCM), and fused magnesia (FM). But what has compounded the barrage of influencing factors impacting this sector, which include the widespread effects of energy and freight cost increases, has been rising demand from certain end use markets. Clearly, the magnesia market is experiencing bittersweet conditions. But those western producers which have monitored and responded to this market transformation, stand to taste success in the near and medium future. REVOLUTION IN WORLD SUPPLY STATUS In essence, while China, as host to a wealth of magnesite resources in Liaoning province, remains a huge producer of magnesia, its supply dominance on the global magnesia market has been considerably weakened. In future, it will mainly aim to supply domestic, and to some extent east Asian markets. Magnesia consumers outside China are now scrabbling for alternative, ?western? sources of supply. At the same time, magnesia producers outside China that weathered the storm of low cost Chinese DBM and FM imports flooding their regional markets for the last 20 years (and many did not), are busy investing in production capacity increases to meet not just demand from falling Chinese supply, but also demand from end use markets which is picking up. And it is not just a matter of expanding capacity of existing magnesia product lines. In the face of plentiful lower cost DBM and FM substitutes from China over the last couple of decades, many western magnesia producers started to switch their focus to the non-refractory markets (eg. environmental, specialities) which promised lucrative opportunities (and still do) and crucially, a lessening of sales revenue dependence on the DBM refractories market. Now we have the likes of Baymag (Canada), Bommag (Serbia/Turkey), and Kumas (Turkey) not only expanding capacities but seriously considering diversifying into DBM and FM production. Perhaps DSP (Israel), having ceased its famous high purity DBM activity as recently as 2005, might even reconsider a return to the ?other side?. But it?s not all DBM and FM. The CCM and specialities markets are also demanding a response, and so Baymag, DSP, Martin Marietta (USA), Premier Chemicals (USA), Qmag (Australia), MGR (Spain), and Magnifin (Austria) are also stepping up to the market on the non-refractory side. From most accounts, the situation with regard to Chinese supply has been described as one of turmoil, with prices rising, leading to improving opportunities for western producers. The majors are conducting huge expansion programmes, such as Qmag, Magnezit (Russia), and the new look Magnesita (Brazil). Even smaller players such as Causmag (Australia) and Dalmia (India) are looking to increase production. In short, the western magnesia supply sector is witnessing a landmark event in capacity investment and market share penetration as China?s previously dominant role begins to weaken (for a review of western capacity expansions see Industrial Minerals, September 2008, p.28). MERGER & ACQUISITION ACTIVITY Another response of course has been a raft of mergers and acquisitions in order to secure resources and supply outside China. These have included private equity groups taking over Magnesita and Qmag; Imerys entering the FM business through UCM; Peñoles further consolidating the electrical grade FM market by acquiring Minco; Martin Marietta acquiring Morton Salt?s Specialty Magnesia Group; Bomex entering the market through Calmag (now Bommag); LWB acquiring Magnesita; and Magnezit?s pursuit of Slovakian magnesia, with Slovmag aboard while currently wooing SMZ. Interestingly, RHI has gone ?the other way?, and has invested in a state of the art joint venture operation at Dashiqiao, Liaoning, with which it aims to secure high quality feedstock for its Chinese refractory plants. Tata Refractories Ltd has announced intentions to follow suit, and other majors, such as Qmag are known to be interested in seeking options. Naturally, there is now renewed interest from several parties in the idled 50,000 tpa DBM/10,000 CCM Jormag facility, Jordan, and the commercially undeveloped Zhargat project, Saudi Arabia. Elsewhere, there will no doubt be suitors for stakes in SMZ, in Slovakia, and Magnohrom, in Serbia, whose respective ownerships are on the block. THE ?CHINA FACTOR? The ?China factor? has been key to magnesia?s market change, and has significantly influenced prices and availability of material to global markets. Resources & production China hosts the largest share of the world?s magnesite deposits, accounting for 26% or 3,319m. tonnes of predominantly sparry magnesite (followed by North Korea, 24%, and Russia, 22%; Wilson 2008). China accounts for 44% of total world magnesite mined (19m. tonnes in 2007) and 50% of the total world magnesia produced (8.2m. tonnes CCM, DBM, FM; Wilson 2008). Russia follows China at 13% of magnesia supply, illustrating China?s dominance of magnesia production. Apart from one producer in Shandong province, central eastern China, the country?s magnesite resources and production are concentrated around the cities of Haicheng and Dashiqiao in Liaoning province, north-east China. Although there are also producers in the Xiuyan district of south-east Liaoning, the Haicheng-Dashiqiao Magnesite Belt hosts the majority of producers. In total these may number 200-300 of large,

Jan 1, 2009

This geometallurgical study examines the gangue mineral variability at the Bingham Canyon porphyry copper mine in Utah. Understanding an orebody?s mineralogy is important for mine and mill planning because it provides information on the size, texture, and distribution of ore minerals, the relationship between ore and gangue minerals, and the extent and type of alteration. Quantification of the mineralogical variability and properties of an orebody provides valuable input to the ore model and may have a significant effect on recovery optimization. This study was designed to be carried out on an initially detailed scale in order to develop a robust methodology for measuring and quantifying specific parameters, such as the distribution of mineral phases, alteration assemblages and fractures from key ore domains at the Bingham Canyon mine (Figure 1). Details of the methodology are reported below. This technique can be applied to testing the impact of mineralogy on a number of processing parameters. [ ] Figure 1. Ore domain map of Bingham Canyon (Kennecott Utah Copper, 2003) showing the 33 geometallurgical ore domains. The samples for this study were collected from the northwest part of the deposit circled on the map. PROJECT BACKGROUND Geology The Bingham Canyon deposit is a large porphyry Cu-Mo-Au deposit with associated skarn and base-metal replacement deposits mined in an open-pit mine measuring about 2.5 miles across and 4,000 feet deep. The deposit is hosted by the Bingham Stock, a Late Eocene to Mid-Oligocene intrusive complex. The skarn is hosted by the Late Carboniferous-age Bingham Mine Formation, which is comprised of quartzites and basal limestones (Babcock Jr. et al., 1998). The Bingham Stock is a composite intrusive complex that was emplaced over a period of about two million years. The oldest phase is described as a fine-grained equigranular monzonite (MZ), which intruded the country rocks at 39.8 ± 0.4 Ma (U-Pb zircon TIMS age) (Parry et al., 2001). Subsequently, the quartz monzonite porphyry (QMP) was emplaced, followed by intrusion of a latite porphyry (LP). The final intrusive phase, which forms narrow dikes that crosscut the Bingham Stock, is represented by a quartz latite porphyry (QLP), which is dated to 37.5 ± 0.4 Ma by 40Ar/39Ar dating of sanidine (Deino and Keith, 1998). Also present, are a minette dike in contact with a QLP dike (Waite et al., 1998; Deino and Keith, 1998), and a biotite porphyry (BP), a quartz latite porphyry breccia (QLPbx), and a pebble dike (Redmond, 2002). The copper orebody is centered above the Bingham Stock and forms an inverted cup shape with three high-grade copper zones extending to depth. Molybdenite mineralization occurs within and extends below the copper orebody, but is not correlated with copper mineralization. The main sulfide assemblage is chalcopyrite, bornite, molybdenite, and pyrite. Gold is locally intergrown with chalcopyrite and bornite (Babcock Jr. et al., 1998; Phillips et al., 1998). The surrounding country rocks host skarn deposits with three main ore types - garnet skarns, massive sulfides, and iron oxides. The garnet skarns contain chalcopyrite and pyrite with magnetite veins. In the massive sulfides chalcopyrite and pyrite occur either in banded sulfides or in unconsolidated microbreccias. The iron oxides contain disseminated chalcopyrite with minor chalcocite and bornite (Harrison and Reid, 1998). The deposit is overprinted by several stages of alteration. Potassic alteration is concentrated at the center of the deposit. It is surrounded and partially overlapped by a propylitic alteration zone. Both zones are overprinted by sericitic alteration. In the northern part of the deposit evidence for argillic alteration can be found (Bowman et al., 1987). Similarly, the skarn deposit was also overprinted by several stages of alteration: wollastonite, idocrase, and garnet in cherty limestones, and quartz and diopside forming in calcareous quartzites. Distally, diopside was replaced by talc, tremolite, dolomite, secondary calcite, and pyrite, and quartz and sulfide veinlets with biotite and actinolite selvages are present. Andradite garnet, diopside, quartz, magnetite, hematite, and copper sulfides were overprinted by wollastonite (Babcock Jr. et al., 1998). Because the monzonite, quartz monzonite porphyry, latite porphyry, and quartz latite porphyry host the bulk of the mineralization, our research is focused on these lithologic units. Geometallurgy On the basis of geological (lithology, alteration assemblages, fracture density, copper mineralization) and metallurgical properties, the deposit has been divided into 33 ore domains by mine geologists and metallurgists (Figure 1). In map view, these domains cross geologically defined boundaries (MZ, QMP etc.). These domains reflect regions of the deposit that have particular, mapable attributes or properties. They reflect a combination of geological and mineralogical characteristics that combine to impact processing. Alteration, for example, as shown by talc mineralization, is one such key feature. Hardness may reflect the absence of sericitic but presence of potassic alteration. Structural discontinuities such as faulting, fracturing, or development of void

Jan 1, 2009

By Bruce D. Hulman, Robert .. F. Gorman

Introduction Groundwater resource evaluation has historically required extensive field investigative work, usually at great cost. More recently, the advent of the microcomputer has made difficult aquifer and groundwater evaluations comparatively simple and less expensive. A groundwater model is a numeric solution to a set of equations that calculates the water level in an aquifer or other types of water bearing strata. A computer will execute the solution of the set of equations rapidly and thereby permit evaluation of large amounts of hydrogeologic data rapidly. Computer modeling of groundwater resources is very often used to forecast the effects of multiple uses of a single groundwater resource. Modeling of heavily used aquifers has proven to be beneficial for averting problems arising from competitive use of a groundwater resource. This paper describes the work tasks performed in order to evaluate a large alluvial aquifer and thereby predict the hydrologic impact of additional groundwater withdrawal. Purpose and Scope Neyer, Tiseo & Hindo, Ltd. (NTH) was retained to evaluate the groundwater supply potential of the Missouri River alluvium underlying the Fairfax District in Kansas City, Kansas (Figure 1). The proposed groundwater supply is being considered for industrial use as non-contact process water and a heat exchange medium for plant climate control. The anticipated peak groundwater demand is estimated to exceed 30 million gallons per day (MGD) during the summer months, with an average daily demand of nearly 25 MGD. The proposed groundwater supply was to be developed from 15 large-diameter production wells located at positions that would minimize potential interference.

Jan 1, 1987

By Wayne A. Ericson, Kirk S. Davis, Cornelis Winkler

BCI has developed a chemical process known as Ecophos® for the multi-industrial Pine Level Project in DeSoto County, Florida. Approximately 85 percent of the phosphogypsum at Pine Level will be converted to a very clean gypsum. The remaining 15 percent, including impurities plus some quartz tailings sand, constitutes what is termed redigestion solids. BCI has developed an alternative to the practice of disposing phosphogypsum in large above-ground impoundments. The proposed disposal method consists of mixing the redigestion solids with clays and reacting the mixture (leached tailings) with lime prior to disposal into the mine excavations as a reclamation soil material. Leachate water quality testing using lysimeter equipment indicates that the pore water associated with neutralized leached tailings meets maximum contaminant levels set for the drinking water standards of radium and selected primary metals.

Jan 1, 1992

By John Thella, Edward McNew, Christina Thella, Mends Emmanuel, Pengbo Chu

Ore sorting is an emerging technology in mineral processing that can produce a significant impact on the total mining and processing economics. The technology is capable of preconcentrating an ore based on differences in the mineralogical characteristics, which can include color, brightness, transparency, size, shape, density or near-infrared response. The current practice of conducting an ore sorting test typically requires large amounts of materials to be sent to a commercial testing facility, which is expensive and time-consuming. Here, we present a novel method to simulate commercial ore sorting on a laboratory scale using a rare earth ore.

Jan 1, 2025

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By R. Pothina

The objective of this research was to develop a mathematical model for gyratory crushers to help in the prediction of energy consumption and to analyze dominant parameters that affect this energy consumption. The development of a gyratory crusher model was achieved in the following three main stages: mathematical representation and coding of the crushing process; building an amperage constant model to derive an energy-scaling formula; and modifying the amperage constant model to represent a full-scale model. Due to their significant influence on feed-size distributions, two blasting parameters, i.e., burden and spacing, were considered. The crusher parameters that affect energy consumption were also identified. A case study of an operating dolomite mine was performed. The results indicated that by changing the burden, spacing and crusher closed-side setting, the overall (blasting and crushing) costs could be reduced by 4.7% to 7.9% annually. It can also be concluded that burden and spacing values have a linear positive relationship with the crusher energy consumption, while closed-side setting values have an inverse linear relationship with the energy consumption.

Jan 1, 2007

By E. Scott Bair

Renewed interest in the vast reserves of anthracite coal in eastern Pennsylvania led to the use of a numerical model for simulating the hydrologic effects of constructing an open-pit anthracite mine. The proposed mine would be approximately 1800-m (5900-ft) long, 1000-m (3300-ft) wide, and 300-m (1000-ft) deep. A two-dimensional, finite-difference, ground-water flow model was used to calculate ground-water seepage rates into the proposed mine, to evaluate the effectiveness of various deep-well dewatering systems, to calculate drawdown in adjacent wells and properties, and to estimate the capacity of the water-treatment plant. Site-specific values of pertinent hydrogeologic parameters were used in the simulations.

Jan 1, 1980

The Mining Foundation of the Southwest (MFSW)promotes public understanding and education related to the mining industry. Towards this goal, the Foundation has funded several projects from donations and fundraising activities. The MFSW was incorporated in 1993 by combining the Mining Club of the Southwest and the Mining Club of the Southwest Foundation. The Mining Club began in 1971 as a social organization. It provided members of the mining community an opportunity to meet. The club also provided a means for public education about mining. In the early 1990s, the club’s efforts were directed mainly toward educational activities. And in 1992, discussions began concerning incorporation into a non-profit foundation to further the public understanding of mining. In 1983, the American Mining Hall of Fame was inaugurated to honor significant contributors to the industry and profession. The Hall of Fame serves to educate people about prominent persons associated with the mining industry, present and past. The honorees number 75. Plaques commemorate their induction and are on display at the Arizona Historical Society’s Museum in Tucson, AZ. The combined honors ceremony and banquet have remained one of the fund raising activities.

Jan 1, 1999

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977