Search Documents

In phosphate flotation, more than 90% of the finer fraction (-35, + 150 mesh) is recovered as opposed to 70% of the coarser material (-16, + 35 mesh). On the other hand, coarser fraction is higher in phosphate content than the finer feed. Consequently, improvement in the coarse recovery is highly desired. It was determined on bench scale that emulsification of the collector (fuel oil and fatty acid mixture) can lead to enhanced recovery of coarse particles. Flotation of phosphate with emulsified collector resulted in improved recovery and grade also on the plant scale.

Jan 1, 1992

By Richard P. Graff

Author?s note: Diversity in practice exists in the application of Generally Accepted Accounting Principles (GAAP) for purchase price allocations with respect to the recognition of Value Beyond Proven and Probable Reserves or VBPP, as defined by the Emerging Issues Task Force (EITF) in EITF 04-3: ?Mining Assets: Impairment and Business Combinations?. This diversity appears to arise from differing interpretations of what constitutes sufficient information to value components of VBPP in business combinations. Concerned with this diversity in practice, respected members of the mining community formed a working group which prepared an issues paper that discussed this diversity and provided recommendations for recognition and valuation of VBPP in business combinations. The working group then submitted this paper to the EITF, requesting further guidance be issued on the concept of VBPP. In conjunction with the submission to the EITF, the working group also provided this paper to the United States Securities and Exchange Commission (SEC) for review and comment. The EITF discussed this issue at its May, 2008 agenda committee meeting. However, it declined to add this topic to the EITF agenda for further consideration. Absent additional guidance on VBPP from the EITF, the working group submitted a proposed definition of VBPP to the U.S. Securities and Exchange Commission for its consideration. The following article, which is consistent with the issues paper that was submitted to the EITF and the SEC, discusses the components of and valuation techniques for VBPP. The correspondence with the U.S. Securities and Exchange Commission, which includes the proposed definition of VBPP by the working group, is attached as Appendix 1 to this article.

Jan 1, 2008

By Charles D. Litton

This Bureau of Mines paper describes a novel fire detector that can be used to discriminate between smoke produced by a fire and smoke produced by a diesel engine. The detector uses a pyrolysis technique whereby a sample of smoke- laden gas passes through a short, heated tube within which fire smoke particles pyrolyze and increase their number concentration and decrease their average size, while diesel smoke particles are unaffected. The detector is designed for use in mines that use diesel-powered equipment where the detection of fires is complicated because of the diesel emissions background levels of smoke and other products of combustion.

Jan 1, 1989

By Robert E. Barry

For new coal-fired power plants, federal regulations require that emissions of sulfur dioxide be limited to 1.2 pounds for every million BTU'S burned. This is equivalent to coal with a sulfur content of roughly 0.7 percent for Eastern bituminous coals and roughly 0.6 percent for Western sub-bituminous coals. The states and their political subdivisions are free to apply more stringent standards and to develop implementation plans covering existing and new units. Most Western-sub-bituminous coals contain less than 1% sulfur and hence their use, in many cases, will allow a utility to meet the regulations. However, there are problems in using such coals in furnaces designed for Eastern bituminous coals, and furthermore it will take many years to open mines and provide transportation facilities to utilities which are now burning coals with a higher sulfur content. Moreover, pending federal legislation would outlaw strip mining on land to which the federal government owns the mining rights. Those utilities who, for one reason or another, intend to continue burning Eastern bituminous coals with sulfur contents in excess of 1 percent are faced with removing SO2 from the stack gases. The alternative of utilizing coal gasification where the sulfur is removed prior to burning in a power plant is still in the early stages of development. Therefore, a large number of processes are under development for SO2 control.

Jan 1, 1974

By M. Oliverio

The Cigar Lake uranium deposit was discovered in 1981 at the south western end of Waterbury Lake, approximately 660 km north of Saskatoon in the province of Saskatchewan (see Figure 1). It is the largest undeveloped high grade uranium deposit in the world. It contains proven and probable reserves of more than 226 million pounds U3O8 at an average grade of 20.7%. The world average grade is less than 1% U3O8. [ ] The ore body is located about 450 m below surface at the interface between sandstone above and basement rock below (see Figure 2). The sandstone is fractured rock and saturated with water. This makes water inflow a real hazard at the mine. In fact there have already been two significant mine inflow events. The first of these occurred in October 2006 and resulted in the flooding of the mine. The second occurred in August, 2008 during mine recovery activities.

Jan 1, 2011

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By S. B. Patton

A computer model, which quantitatively utilizes the relationship between the interactive and dynamic processes of methane drainage, mining, and ventilation, is presented. The model includes simulation of the coalbed methane reservoir for prediction of gas-emission rates under the influence of degasification wells and longwall mining, ventilation network-generation, and ventilation simulation. As mining progresses step-wise through the coalbed-methane reservoir, the ventilation network is created and subsequently simulated, iteratively determining fan requirements to safely reduce methane concentrations. The model can be used to quantitatively study the effectiveness of methane degasification on the ventilation system in a longwall panel.

Jan 1, 1992

By Julian S. Edwards, C. Frederick C. Pearson, Sevket Durucan

Information gained at the site investigation stage of the Carsington aqueduct project led the designers to suspect that methane might be encountered during tunnelling and therefore gas detection techniques, including emergency shutdown systems, were introduced. After construction, on completion of the excavation and lining of the tunnels, a survey showed that methane was entering the aqueduct dissolved in infiltrating groundwater. General body air concentrations were very low but on closure methane concentrations rose rapidly within the aqueduct. A research project has now been initiated to investigate the mechanism of methane generation and entry rate into the system, the results of which are being taken into account in the preparation of future operating procedures.

Jan 1, 1989

Bauxite mine rehabilitation is an important stage of today’s bauxite mining activities. To get an overall picture on those activities the International Aluminum Institute (IAI) has been carrying out Bauxite Mine Rehabilitation Surveys since 1991. The most recent survey from 2003 covers 70% of the world’s bauxite production and 23 corresponding companies from 12 countries. The survey activities show that nearly all operations refer to a sophisticated environmental management strategy. By setting up a review scheme based on the principles of the Global Reporting Initiative the compliance of this survey to aspects of Sustainable Development has been reviewed. The Clarification of a multitude of aspects based on the GRI guidelines helped to structure recommendations and relate them to the survey as such but also to the different stakeholders involved.

Jan 1, 2005

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By F. Freme

For the second time in four years, the coal industry was brought to the forefront of the nation’s consciousness in 2006, as two separate events unfolded which involved coal miners trapped underground. Unfortunately, the tragic results of the 2006 incidents were not the same as in 2002 when the trapped miners were all successfully rescued. In January, two different incidents, both in West Virginia, focused the public’s attention on the dangers that miners face on a daily basis. As a result of these unfortunate events new legislation requiring improvement in safety in underground mines passed both at the federal and state level. In 2006, a total of 47 miners died on the job, matching the total number that occurred in 1995, and more than double the 22 killed in 2005. Notwithstanding those tragic events, coal production in the United States reached another record level in 2006, ending the year at 1.05 Gt (1,161.4 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2006 was 27.1 Mt (29.9 million st) higher than the prior record set in 2005 of 1.03 Gt (1,131.5 million st). Although coal production rose in 2006, U.S. total coal consumption actually declined for the year. Coal consumption decreased in the electric power sector by 1.1 percent, while coking coal consumption decreased slightly. Only the other industrial sector had higher coal consumption in 2006, increasing by 0.3 percent. (Note: All percentage change calculations are done at the short tons level.) U.S. coal exports declined slightly in 2006, while coal imports again reached a record level. The excess production over consumption allowed total coal stocks to increase significantly during the year, as electric generators rebuilt their stockpiles that had fallen substantially in 2005 because of missed shipments in the second half of that year.

Jan 1, 2007

By H. I. Morrison, A. J. deVilliers, D. T. Wigle, H. Stocker

INTRODUCTION At the end of 1959, high levels of radioactivity attributed to radon and its daughter products were discovered in the fluorspar mines at St. Lawrence, Newfoundland. These levels were presumed to be the cause of an unusually high incidence of lung cancer among the fluorspar miners (deVilliers & Windish, 1964) (Parsons et al. 1964). The mining of fluorspar (calcium fluoride) began in 1933 as open pit operations but converted to standard underground mining procedures in 1936. During the second world war, production was greatly expanded as a result of increased demand for fluorspar used in the production of steel. Wet drilling was first introduced into general use in 1942. Ventilation was mainly by natural draft occasionally supplemented by small blowers. The amount of ventilation varied greatly between mines as well as over time. For example, one large mine, the Iron Springs mine, had only a single small raise to the surface some 600' from the central shaft. Other mines, such as the Director mine, had a number of raises to the surface and, as a result, had far better ventilation. Mines also varied by the amount of ground-water which seeped into them. In the early 1950's, an unusually large number of lung cancer cases were diagnosed among the fluorspar miners. As a result, in 1956 and 1957, J.P. Windish of Canada's Department of Health and Welfare tested for possible causative agents in the mines. Unfortunately, radon measurements were not conducted until 1959 and 1960 when Windish tested Director mine as did the A.D. Little company in 1960. As a result of the high radon levels found, mechanical ventilation was introduced and the concentration of radon dauthers fell, on the average to well below 1 WL. During this period, lung cancer cases continued to be diagnosed with 29 lung cancer deaths recorded by 1964 and 71 by 1971. As of July 1981, 105 lung cancer cases had been identified (Hollywood, 1981). Previous reports concerning the fluorspar miners have dealt in detail with the factors in the occupational environment and discussed occupational mortality patterns. The purpose of this paper is to review further the mortality experience with particular reference to lung cancer in relation to cumulated radiation exposure and to describe briefly our ongoing study of this group. METHODS Occupational histories were prepared for men who had been employed by the mining companies at St. Lawrence during the period 1933 to 1977. The histories were compiled from company records except for the period 1933 to 1936, records for which were lost in a fire; however, the occupational histories for this period were completed by searching census records and interviewing company officials, ex-employees and others. In addition, occupational and smoking histories were also obtained for some miners during a survey conducted in 1978. Occupational records included name and date of birth as well as the type, place and hours of work by year. For each year prior to 1960, hours of work were converted to working months (1 WM = 167 hours) and were multiplied by the estimated average radon daughter concentration in working levels (WL) to yield the annual radiation exposure in working level months (WLM). Pre-1960 radiation levels were estimated on the basis of the history of mining methods employed, ventilation history of the mine, type and place of work and conditions under which the first radiation measurements were made in 1959 and 1960 (deVilliers and Windish, 1964). During the period from 1960 to 1967, the average exposure was about 0.5 WL. Beginning in 1968, radiation levels were measured more frequently, and, beginning in 1969, daily exposures for each worker were recorded based on radiation levels in the place worked on a given day. Mortality data were obtained from medical certificates of death. In a small number of cases, medically certified death certificates were unavailable. In these cases, probable cause of death were obtained from forms completed by the local clergyman (returns of death), parish records, information obtained from interviews with family members of the deceased and/or hospital information, before assigning a cause of death. Data obtained from these sources were found in Tables 1, 2 and 4, cover the time period 1933 to 1971. Data in Table 3 as well as in Figures 1 through 3 cover deaths from 1933 to 1977, and includes only those miners for whom medical certificates of death were available. Two medically certified causes of death were changed from other causes to lung cancer on the basis of pathology reports.

Jan 1, 1981

By John E. Edkins

Metal sulfides, chiefly pyrite and mFnor sphalerlte zssociated with che Herrin (No. 6) coal member of the Pennsylvania Carbondale Formation, have been concentrated in a coal refuse deposit in southern Illinois. Oxidation of pyrite has produced highly acid waters with high concentrations of iron, zinc (up to 200 parts per million) and toxic trace elements that have leached downward to a water system perched on glacial drift. Chemical, petrographic, low-temperature ashing and x-ray diffraction were performed on cores. The data show that economic recovery of zinc and other trace metals is unlikely at this site. Energy (coal) recovery at the Superior Washer site is possible if resultant environmental problems are considered in the planning.

Jan 1, 1981

By Peter Amelunxen, Kain Nugent, Brandon Akerstrom, Willem Duyvesteyn, Todd Harvey

In 2024, Capstone Copper Corp commissioned a new sulfide flotation plant at Mantoverde in the Atacama region of Chile to process copper ore at a design rate of 32,000tpd. The pyrite associated with the copper ore body contains cobalt in solid solution, with Co replacing Fe in the pyrite matrix. As per the existing sulfide flotation flowsheet most of the pyrite is depressed and sent to tailings via the cleaner scavenger tail stream. A new project considers the recovery of the pyrite from the cleaner-scavenger tails via froth flotation to produce a cobaltiferous pyrite concentrate, which is then leached via the existing dynamic copper leach pad to oxidize the pyrite and dissolve the cobalt. The cobalt is recovered from the solution by treating a bleed stream of copper SX raffinate through a continuous, counter-current ion exchange (CCIX) facility. This approach to by-production of cobalt confers numerous benefits, including reduced costs compared with alternative cobalt recovery processes, reduced acid consumption in the heap leach, increased copper production, and reduced acid mine drainage potential due to the removal of pyrite from the mill tailings.

Feb 1, 2025

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By Carl-Henrik Knudsen, Rolf Tore Arnesen, Eigil R. Iversen

Recovery of iron and copper from acid mine drainage was studied in pilot scale at a continuous treatment plant at the mine site of the King's mine in Roeros, Norway. The average load on the plant was 1 m3/h. The process tested in this project is a three-step process consisting of: 1) Fe(OH)3 precipitation at pH 3.5, dewatering of iron sludge and transport to ferric chloride plant; 2) after filtration precipitation of residual metals at pH 9, concentration of metal sludge by flotation; 3) extraction of metals from the sludge with sulphuric acid followed by recovery of copper by electrolysis. The copper could be used for local production of different crafts, but this condition needs a further evaluation. The process economy at a full scale plant is evaluated.

Jan 1, 2000

By Y. J. Wang

The ventilation network problem, having both fixed and nonfixed operating points as control devices, is examined in this paper. Emphasizing the concept of solving a system of n equations in n unknowns, this paper presents the generalized problem formulation, some conditions under which the problem does not have a unique solution, and a solution procedure based on the Newton (or Newton-Raphson) method. A numerical example is included.

Jan 1, 1989

By M. S. Celik

Salt-type minerals are usually floated with anionic and cationic collectors. Flotation of a number of systems has been reported to remarkably increase above the concentrations where surface precipitation of collector-metal salt is initiated. Some studies attribute this phenomenon to heterocoagulation of oppositely charged collector colloid and mineral particles. In this study, examples are given on boron minerals to demonstrate that the high flotation region occurs when particles, colloidal precipitates and bubbles acquire a similar charge which induces Van der Waals interactions resulting in hydrophobic bonding.

Jan 1, 1995

By L. Barry Phelps

The complexity of surface mining operations is increasing as attention is directed towards mining larger tracts of lower grade, higher cost deposits. Large tonnage requirements from these mines necessitate utilization of many large pieces of equipment. This equipment must be utilized efficiently, with production maintained at or near designed capacities. Basically, the problem is to select, size, and schedule equipment to maximize profits and minimize adverse environmental impacts (Anon., 1977). The time, manpower, and cost limitations required to analyze a wide variety of situations and alternatives in planning surface mines have been sidestepped with the application of simulation methods using a digital computer. Since a simulator can be programmed to represent the situations which are to be analyzed, many alternatives can be evaluated in a relatively short time. Input variables are easily changed and the resulting changes which take place in the system can be analyzed. When standard methods of analyses are applied, weeks and many man-hours are involved in analyzing large-scale mining operations. At the same time many simplifying assumptions must be made since these operations are dynamic and transient. Hence, it becomes difficult to make sound engineering decisions and take proper and timely corrective action in the absence of simulation methods. This chapter is concerned with the application of one such method, namely, the open-pit materials handling simulator (OPMHS) developed by the Mining Engineering Section, The Pennsylvania State University (Manula, Albert, and Ramani, 1977).

Jan 1, 1979

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969