Search Documents

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By Éder Domingos Oliveira, Carlos Antonio Morais, Ruberlan Gomes Silva

The objective of this study is to assess the impact of different reagents, such as limestone, lime, magnesium oxide, and sodium hydroxide, in experiments carried out in the single purification step and in two consecutive purification steps by raising the pH of a rare earth sulfuric liquor with the aim to remove or reduce the impurity concentrations in the rare earth sulfuric liquor. The choice for the best purification condition was made based on the minimum loss of rare earth elements (REEs), reagent consumption, and residue generation. The exploratory experiments show that it takes place in the two consecutive purification steps, the first one consists in dosing the limestone pulp until it reaches a pH of 3.5 followed by an addition of a lime pulp reaching a pH of 5.0. Under this condition, the results were a total removal of Fe3+, PO4 3− , and Th4+ ions and a reduction of 99%, 87%, and 37% w/w in the Al3+, UO2 2+, and SO4 2− concentrations, respectively, in the purified rare earth liquor. Furthermore, the lowest REE losses (8.3% w/w) and reagent consumption (4.3 kg/m3 ) and also a low residue generation (7.5 kg/m3 ) were observed in this condition. Despite reaching similar results regarding impurity removal, the experiments done with the addition of limestone, lime, magnesium oxide pulps, and sodium hydroxide solution in the single purification step, where the pH was raised to 5.0, presented higher REE losses (64.9%, 42.5%, 44.8%, and 60.9% w/w, respectively) and a higher residue generation (43.2, 25.1, 11.1, and 13.6 kg/m3 , respectively). This occurred due to the co-precipitation of salts containing rare earth elements in their composition. The experiments conducted with limestone, lime, and MgO resulted in a higher consumption of reagents, while the same result was observed when NaOH was used (4.3 kg/m3 ). In the experiments carried out with the addition of magnesium oxide and sodium hydroxide, the respective purified rare earth liquors presented a high concentration of magnesium, sulfate, or sodium, which could impact the quality of the marketable rare earth salts, whereas the salts obtained under the best condition observed in this study seem to be amenable for use as raw material in an attempt to obtain rare earth products with an acceptable chemical quality.

By Z. Stanojevic-Simsic

The aim of this paper was to study sludge dewatering. The sludge which was examined in laboratory scale was produced by neutralization of a mixture of metallurgical wastewaters. Experiments were carried out using synthetic wastewaters with chemical composition similar to that of metallurgical wastewaters, resulting from electrolyte regeneration, copper refining and precious metals recovery. During investigations gravitational and vacuum techniques were examined. Parameters such as water volume, height of sludge and time of dewatering were monitored. In this paper the results obtained are presented and discussed. The application of vacuum filtration enables better dewatering and compaction of sludge.

Jan 1, 2006

By Peter G. Sechiari

The Rio Tinto-Zinc Corporation Limited (RTZ), through it exploration company Riofinex, commenced exploration for bauxite in the Amazonia region of Brazil during 1970. Following' encouraging indications, exploration licences were taken out and an exploration programme was initiated In February 1975, a preliminary 'feasibility report indicated that a project, based on the Miltonia plateau located close to the town of Paragominas in the State of Para, was viable and that barging might offer an economic solution to getting the product to an ocean-going port. A, decision was taken in April 1975 to proceed with a full feasibility study. In the latter stages of the study, an engineering consortium of Mendes Junior and Bechtel do Brasil was employed to review, and modify if necessary, the concepts that RTZ had developed for the project's operation. With these concepts agreed, the consortium was requested to make capital and operating cost estimates, and these became available during February 1978. The deposit is being developed by a Brazilian company Mineracao Vera Cruz S.A. (MVC) in which the present share-holding is owned 64 percent by RTZ and 36 percent by Companhia Vale do Rio Doce (CVRD). RTZ is a British based international group of mining and industrial companies with interests in almost every major metal and fuel. CVRD is a Brazilian mining company, 85 percent owned by the Brazilian Government, with a major interest in iron ore and also other non-ferrous metals. It is intended, in due course, that the company will become majority owned by Brazilian interests.

Jan 1, 1979

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By G. Meiers, M. O’Kane

Dry cover systems as a closure option for management and decommissioning of waste rock and tailings is a common prevention and control technique used at numerous sites around the world. Numerous site-specific factors control the long-term performance of dry cover systems. Site-specific climate conditions are one of the key factors to consider when determining the objectives of a dry cover system because these conditions will significantly influence long-term performance. There are advantages and disadvantages of characterizing the site on an annual basis as generally a “dry” site (annual potential evaporation greatly exceeds annual precipitation), or generally a “wet” site (annual precipitation meets or exceeds annual potential evaporation). The field performance monitoring data and discussion presented herein illustrates the caution that is required when using these “annual” criteria for characterizing site climate conditions. Numerous sites exist where precipitation exceeds potential evaporation on an annual basis; however, the site typically experiences hot, dry summer months where evaporation greatly exceeds rainfall. These dry summer conditions have a strong influence on long-term performance. In contrast, sites where potential evaporation exceeds precipitation on annual basis, typically experience periods of the year when a moisture surplus occurs, which also impacts on long-term performance. This paper uses soil-atmosphere cover design modelling and field performance monitoring from sites in Canada, Australia, and the United States to demonstrate the importance of considering site-specific climate conditions when predicting long-term cover system performance.

Jan 1, 2003

By Hans von Michaelis

It is appropriate that this opening session of HAZPAC '91 and Randol Gold Forum CAIRNS '91 should address the question of what the two industries can learn from each other. The panel is made up of members with experience in both industry. Several are experts on managing both hazardous waste and the mine/mineral processing environment. There is a marked difference in the regulatory needs with respect to treating and disposing of mining and mineral processing wastes, and "hazardous" or industrial waste materials. The topic of this paper is on the things that the two industries have in common: Many of the processes and technologies that are being used or are currently being developed for treatment of hazardous waste are the same or similar to the processes that have been used for decades or k,nger in the mineral processing industry. Hazardous waste treatment and remediation of contaminated solid and/or groundwater is a relatively new industry. Many of the practitioners in this new industry are relatively inexperienced in most of the "new" technologies that are being applied or developed.

Jan 1, 1991

By H. Braun, T. Kind, K. Gloe, D. B. Dreisinger, H. Stephan, O. Heitzsch, G. A. Kordosky

Municipal garbage incineration processes with coupled wet flue gas cleaning systems generate effluents containing toxic heavy metals such as mercury, zinc, cadmium and copper. The separation of these metal ions from the obtained scrubbing solutions is possible using liquid-liquid extraction. Extraction studies has been performed both with commercial extractants Aliquat 336, di(2-ethylhexyl) phosphoric acid and novel chelating agents as acyl thiourea and lipophilic oxathiaaza alkanes. Advantages and disadvantages of the investigated extraction systems are discussed. The paper reports on the basic research as well as on the testing in a laboratory scale.

Jan 1, 1993

By W. A. Rickelton

Trialkylphosphine sulphides, in contrast to their well known oxide analogues (1,2,3,4), have received comparatively little attention as metal extractants and previous studies have been biased toward analytical rather than commercial solvent extraction applications (5,6,7). The sulphides are soft Lewis bases and only from complexes readily with the limited number of metals in the periodic table which can be classified as soft acids (8) e.g. Ag+, Hg2+ and Pd2+. Consequently, these compounds tend to be more selective than the broad-spectrum, hard-base, phosphine oxide extractants such-as TOPO (trioctylphosphine oxide). The purpose of this paper is to describe a potential application of one phosphine sulphide, CYANEX® 471X extractant, in the selective recovery of silver from base metal sulphate solutions. CYANEX 471X is triisobutylphosphine sulphide (TIBPS).

Jan 1, 1984

By Khosrow Badiozamani

Depletion of easily accessible coal reserves and stringent competition in coal marketing has led to the coal industries' need to more accurately assess alternate development scenarios and to develop well-conceived produc¬tion plans. This, in turn, has encouraged the active use of the computer during resource eval¬uation and mine planning. Morrison-Knudsen, (M-K) has developed proprietary software, known as "EAGLES", to support not only its own mine planning and development activities but also the mining industry in general. The EAGLES system provides complete geologic modeling, mine planning, production modeling, equipment modeling, and cost and financial modeling capabilities. In addition, EAGLES can be used for geotechnical studies, environmental assessments, and surface and groundwater hydrological evaluations. Another important tool used in today's mine development is Landsat (remote sensing). Landsat is especially useful in the evaluation of mining activities at remote mine locations and for megascale assessments of geologic structures and hydrologic regions. The use of scientific systems in the development of surface mines is being well integrated into today's mining operations and will be a major factor in the planning, development, and operation of mines in the future.

Jan 1, 1985

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By I. Tsolas

Sustainable development is becoming increasingly more important for the mining industry and therefore mining companies should be able to measure their progress towards sustainability. Greek Public Power Corporation (PPC) S.A. is a company which produces lignite in open cast mines in Western Macedonia and in Peloponnesos. The present paper uses operational data kindly offered by PPC S.A. to derive sustainability indicators by means of Data Envelopment Analysis for three large scale lignite open cast mines of PPC (i.e. Main Field, Kardia Field and South Field mines). It also examines three environmental parameters related to the contribution of these mines to sustainable development; namely, the annually produced volume of waste masses, the annually produced quantity of ash from the lignite combustion and the annual volume of pumped water. The calculated sustainability indicators were keeping constantly better during the last years of the different periods for each one of mines studied here, showing that the mines met their goals from both economic and environmental aspects during the last years of their operational periods studied. The contribution of open cast lignite mines studied here to sustainable development can be monitored by the derived indicators analyzing annual mine operational data. The derived indicators can serve as tools to detect where improvements can be made, though another potential use of these indicators can also be during the preparation of feasibility studies or environmental impact studies using necessary benchmarking data.

Jan 1, 2007

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By C. O. Brawner, J. Kalejta II

The classical approach to control rock fall and ravel in open pit mining has been to use catch benches. The width and volume of benches is most dependent on the bench height, size of loading equipment, blast damage to the face and mining regulations. This was compatible with open pit slopes of less than about 45°. As our understanding of rock mechanics and blasting control has improved over recent years, much steeper rock slopes can be developed at many open pit mines. However, narrower benches result with less rock fall capacity. The transportation industry has been very successful in using catch fences to protect highways throughout North America and Europe for years. The authors recommend that cable and ring net fences have a potential major application in open pit mining to allow steeper rock slopes with significant economic benefit. This paper outlines the application, design and operation of catch fences in surface mining for specific conditions. Typical case examples are presented.

Jan 1, 2002

By Nico Sutmoller, Rich Palladino

Underground voids present a unique geotechnical engineering challenge. This paper will address materials and transportation mediums that are typically used for backfilling underground voids with native material. After reviewing traditional backfill and transportation methods, this paper will explore the advancing technology of foam transportation and the advantages of using this technology for transporting fill materials into underground voids to backfill them with Liquid-Sand. The paper will also review the benefits that Liquid-Sand brings to these applications and highlight specific case studies in which foam transportation has proven effective and provided cost-effective, environmental benefits.

Feb 1, 2025

By Jacob D. Baker

Sulphur dioxide is a versatile gas which has many uses throughout Pulp & Paper, Chemical, specialty Chemical, Mining and other industries. During recent years, S0 2 consumption and distribution patterns have resulted in renewed interests for liquid S0 2 and on site gaseous S02 manufacturing facilities. one relatively new use for S0 2 in the Mining Industry is its use for cyanide detoxification. Our purpose in this paper is to describe the process steps, economics and general technical features of so 2 gas generation using a Jet Type sulphur Burning System.

Jan 1, 1991

By Mark A. Krall, Robert L. Geddes, James C. Frost

Introduction The Conda Partnership's Dry Valley phosphate mine is a thinly bedded, multiple seam open-pit mining operation where selective mining techniques are used to recover phosphatic shales. The mining methods used are truck/shovel and scraper/dozer operations. Ore is shipped 32 km (20 miles) by rail to a beneficiation facility. The ore is upgraded by washing and calcining. The mine and beneficiation complexes are owned by the Conda partnership. It is a joint venture between Beker Industries Corp., of Greenwich, CT, and Western Co-Operative Fertilizers (US) Inc., of Alberta, Canada. The Partnership operates as a separate entity of the two partners. The Dry Valley mine is located 48 km (30 miles) northeast of Soda Springs in Caribou County in southeastern Idaho. The mine is situated on the Caribou National Forest. Mining operations take place between 2 and 2.4 km (6400 and 7900 ft) in elevation. It is accessible partly by 32 km (20 miles) of paved roads and 16 km (10 miles) of dirt roads. The winters are long and severe, and the summers are short and mild. This article describes the history, geology, exploration, mining, and reclamation that makes this mine Idaho's largest producing mine and the western US' leading phosphate producer. History and production In the mid-1950s, Western Fertilizers of Salt Lake City, UT, drove an exploratory drift in Maybe Canyon. A large bulk sample of phosphatic shales was analyzed for phosphate content and processing characteristics. No large scale mining or processing operations were undertaken. In the late 1950s, the Dry Valley property was sold to Central Farmers of Chicago, IL. No major operations took place. In 1964, Central Farmers sold the property to El Paso Products Co. of Odessa, TX. El Paso Products supervised the mining operations of Wells Cargo Mining Co. from 1965 through 1967. During this time, El Paso Products built a beneficiation facility and a fertilizer complex in Conda. A 32-km (20-mile) railroad was also constructed from the mine to this facility. From 1968 through 1972, the mine was shut down due to a depressed fertilizer market. In 1972, El Paso products sold its ore reserves, beneficiation plant, and fertilizer complex to Beker Industries Corp. In 1979, Beker Industries sold 50% of its ore reserves and 50% of its beneficiation plant to Western Co-Operative Fertilizers (US) Inc., of Alberta Canada, forming the Conda Partnership. It has operated the mine and beneficiation plant since January 1979. From the mid-1950s to the mid-1960s, no substantial production took place. From 1965 to 1967, El Paso Products stripped 3 Mm3 (4 million cu yd) and mined 2.3 Mt (2.5 million st). From 1972 through 1983, 50 Mm3 (66 million cu yd) were stripped and 18 Mt (20 mil¬lion st) were mined. Geology The Wells Formation forms high ridges and hillsides in the Dry Valley area. It is best exposed along the west face of Dry Ridge. It forms the imposing wall on the east side of Dry Valley. The formation is divided into two members. The lower member, about 213 m (700 ft) thick, is dominantly thin to medium-bedded limestone and silty limestone. It contains nodules and stringers of chert and minor sandstone. The upper member is composed principally of thick-bedded to massive cross-bedded, light-gray to orange-yellow, fine grained sandstone. There is some interbedded brown to light-gray limestone. This member varies from 369 to 457 m (1300 to 1500 ft). Recent investigations indicate that the upper Wells is of Permian age. Under some conditions, the Wells may be water-bearing. Otherwise, it has no apparent economic significance. Grandeur Member (Park City Formation) Overlying the Wells Formation is a distinctive light-gray to white dolomitic fossiliferous limestone. This unit has been identified by the US Geological Survey (USGS) as the Grandeur Tongue Member of the Park City Formation. This member is sometimes absent due to its contact with the Meade Peak Member of the Phosphoria Formation. It is easily detectable by its color, hardness, and fetid odor. Phosphoria Formation The Phosphoria Formation of Permian age was named from Phosphoria Gulch, Bear Lake County. The formation has been studied extensively and developed for its economically valuable phosphate reserves.

Jan 11, 1985

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

By C. A. Holley

Agitative agglomeration is a rapidly expanding field related to many chemical processes. This paper reviews many processes and the particular type of agitative agglomeration that is utilized with each. Many new innovations to produce granular products in place of powder are explored. The operation and theory of the many types of agitative agglomeration equipment is reviewed.

Jan 1, 1988