Search Documents

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991

By James R. Arnold

Over the past few years several commercial wetting agents and drying aids have been tested in the lab and in the plant at Gold Fields Mining's operations at Mesquite and Ortiz. The major goal was to increase recovery with these surfactants by improving the permeability of the pad and increasing the rate of penetration through the rock.

Jan 1, 1988

By D. Y. Geng

Longwall mining is a relatively new mining method in the United States. Early trials in the eastern and central coal fields were not successful, mainly because, among others, the face supports did not have sufficient capacity. It was not until in the late 1960's, when the high- capacity self-advancing powered supports became available, that longwall mining was successfully reintroduced. Since then the number of mines employing the longwall method has been steadily increasing. It has reached approximately 7.5% in 1981. Currently longwall mining is used mainly in the Appalachian coal field. The seam depth ranges from 150 to 2500 ft. but mostly between 300 and 1400 ft. The seam thickness ranges from 32 to 144 inches with the majority between 40 and 100 inches. Nearly all longwall mining are in flat or nearly flat seams extracting in single slice, although one inclined and one thick seam longwall mining have been either operated or initiated in Colorado.

Jan 1, 1983

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By L. R. Hossner

Chemical and physical properties of surface soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the existing surface soils, especially when these soils are classed as prime farm lands. In Texas, materials from the Carrizo, Calvert Bluff, Simsboro, and Hooper Formations overlie the lignite. The Carrizo Formation consists of thick clean sands with poor water and nutrient retention capabilities. These materials are least suited for placement of the surface of reclaimed land. The oxidized, medium textured overburden from the Calvert Bluff and Simsboro Formations possess adequate water and nutrient properties and are better suited for sustained plant growth. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation. However, caution must be exercised in vegetating these materials since they may contain acid forming sulfide minerals.

Jan 1, 1982

By Michael Drozd

The operation of an activated charcoal system has five separate unit operations. These unit operations have common points for CIP, CIL and CIS system, which vary widely in application. a. Absorption b. Desorption (Stripping) c. Acid Washing d. Reactivation e. Carbon Handling ( carbon transportation, sizing, de­watering, etc.) Cost optimization starts with the basic operating parameters (design philosophy) set down at the time of engineering design. This parameters undergo almost immediate change due to site specific ore requirements, throughput changes, operator requirements or reagent availability. Activated charcoal is sometimes viewed as simple, uncomplicated reagent that requires not optimization. To some extent, this statement is true, but under most circumstances, if the time necessary to optimize the use of activated charcoal is available, the effort is rewarded with significant savings. CPL-Carbon Link has embarked upon a program of supplying technical support with its activated charcoal. Several operation in the United States have under taken to have CPL-Carbon Link do an operational survey to determine if potential savings are possible. CPL-Carbon Link has offered to do these surveys for projects that are clients or simply would like to have CPL-Carbon Link review their operation. The information accumulated by CPL-Carbon Link is being used to attempt to fashion industry standards so that a common reference point came be establish for activated charcoal usage.

Jan 1, 2000

By A. Mertzanis

The way and methods used for the surface mining of bauxite until the end of the twentieth century in the area of Ghiona, resulted in a significant burden to the natural environment, especially in the cases where it covered extended parts of forests and forest areas as well as important geomorphological formations. The impacts from the surface mining of bauxite which in fact constitute the object of this study relate mainly to the interruption of the natural continuity of the land relief and the alteration of the natural geomorphological activities and are due to: a) the alternating excavations with fronts of great heights, b) the depositions of large volumes of waste materials which originate from the revealing of the ore and c) the dense road network constructed in order to get access to the mine locations.

Jan 1, 2006

By L. C. Atkinson, E. A. Azrag, T. M. Hanna

The results of using a simple analytical solution and a relatively complex numerical model to estimate ground water inflow to an open pit mine are compared. The analytical solution assumes lateral, radial flow to a fully penetrating pit in an idealized confined aquifer, whereas the numerical model simulates fully three-dimensional flow to a partially penetrating pit from a water table aquifer. The latter is a more realistic simulation of the problem, but the former method is significantly easier to use. Comparison of the results obtained with the two methods for some typical hydrogeologic conditions encountered in mining yields ratios between them in the range of 0.2 to 0.6. These values can be used as a coefficient in the Pit Flow analytical solution to produce reasonable estimates of in-flow even when there are significant differences from the idealized conditions implicit in its application.

Jan 1, 1995

By Bruce K. Cantrell

As part of a continuing study of diesel exhaust aerosol characteristics, the Bureau of Mines has applied Chemical Mass Balance (CMB) model source apportionment analysis to evaluate a size selective sampling method for determining the separate diesel exhaust and coal dust aerosol concentrations in a diesel equipped coal mine. Size selective sampling was used under the premise that diesel exhaust aerosol dominates the submicrometer aerosol size range, while most of the mineral dust aerosol is greater than 1 m. A micro-orifice, uniform deposit impactor (MOUDI) was used as the size selective sampling method. Concurrent samples of mine aerosol were collected using a dichotomous, respirable aerosol sampler. This sampler separated the fine and coarse size portions of its sample at 0.7 m. Trace element concentrations for in-mine aerosol sources and the dichotomous samples used by the CMB model were measured using Instrumental Neutron Activation Analysis. The CMB analysis, applied to both the fine and coarse fractions of the respirable mine aerosol, yielded the mass concentration contributed to each by diesel exhaust and mineral dust aerosol sources. The MOUDI size distribution data were analyzed using nonlinear regression to parameterize the fine and coarse fractions of the sampled aerosol and to estimate the contributions to each fraction from both coal dust and diesel aero- sol sources. For the diesel mine visited, analysis of the MOUDI samples yielded a value for the fraction of the fine aerosol attributable to coal dust of 15[]7% fine fraction coal from analysis of the MOUDI samples versus 25[]4% from the CMB analysis. The remainder of the fine aerosol in the mine was diesel exhaust aerosol. CMB analysis confirms the original premise for such sampling. After correcting for the presence of coal dust in the fine aerosol fraction, analysis of the MOUDI size distributions yielded estimates of respirable mineral and diesel exhaust aerosol concentrations that were accurate to with-in 10% of values determined by the CMB apportionment.

Jan 1, 1987

By J. C. Yingling, J. W. Leonard

Introduction The absence of coal-face particle management heavily penalizes the transportation of coal from initial loading to final consumption. The penalties include dust problems, significantly reduced mine-loading-cycle productivity, mine-belt spillage, excessively high coal-preparation costs, chute blockages and dangerous pulverizer blockages at the final point of utilization. Fine particles commonly cause environmental and economic problems. It is well known that these fines can cause safety and environmental dust problems. But it is not well understood that these fines can also swell broken coal to a point where 5% to 15% more time and capacity must be used to deliver the same tonnage. In this paper, methods and rewards for reducing and/or managing fines at the mine face are discussed. Computer-based loading-cycle model productivity estimates, viewed from a new perspective, are made on the basis of material volume rather than on the long-established, and frequently misleading, basis of tonnage. It is typically the volume of broken material being transported that defines the capacity of a given transportation system, while the corresponding tonnages are merely a reflection of the specific material densities. Published evidence suggests that the swelling of broken coal can be decreased very significantly using small quantities of certain nonfrothing chemicals, which are added to mine-face spray water, and by employing improved mine-face breakage practices. In a future paper, the effects on transportation productivity beyond the coal mine will be discussed. The precursor to the work presented in this paper, involving the bulk density improvement for broken coal and the subsequent production gains for underground coal mines, was earlier presented in Leonard and Newman (1989). In the past, this topic has been studied and practiced only in byproduct coking in the steel industry. However, a potential exists for an increase in coal-industry productivity by improving the bulk density of coal to yield a subsequent reduction in delivered cost. This can occur with breakage, handling and treatment methods resulting in the loading of greater quantities of coal in fixed volumetric capacity haulage units such as mine cars, shuttle cars and scoops. Laboratory-based experiments to achieve an increase in productivity by increasing coal bulk density were discussed in Leonard, Paradkar and Groppo (1992). Chemical techniques using small quantities of commercially available reagents (surfactants) resulted in about a 13% to 15 % increase in bulk density, which was thought to produce a proportional increase in the productivity of a mine, together with a subsequent reduction in cost. The idea is to mix the reagents with the water that is used to spray coal during mining. In this paper, the impact of bulk density improvements on production rates is presented. Increases in production ranging from 60% to 88% of the bulk density increases are projected. This analysis was performed for atypical continuous-miner section. In the following sections, discussion and results of the analysis are presented. Discussion An analysis was performed to ascertain the impact of bulk density improvements on face-production rates for a typical continuous-miner section. Figure 1 illustrates the section layout and cut sequence. This layout and sequence is identical to the case described in King and Suboleski (1991). As can be seen, the section uses five entries and 12.2-m cuts that are taken by a remotely controlled continuous miner. The seam height is 1.5 m and two shuttle cars (5.7 t nominal capacity) are employed for haulage from the miner to the section feeder, which, throughout the cut sequence, is positioned as illustrated in Fig. 1. The simulation model was coded in the SIMAN simulation language. The major impacts of increased bulk density improvements on such a production system are as follows: •Shuttle-car payloads, in terms of the mass of coal transported per haul cycle, are increased proportionally to the increase in bulk density that results from the application of surfactant. •Shuttle-car discharge times should remain largely unchanged, because they are determined by the volume of material that is discharged, rather than the mass, and this volume does not change.

Jan 1, 1996

By S. R. Wardwell, M. J. Robison

INTRODUCTION The first phase of the Los Angeles Metro Rail Project consists of 7.1 km of subway and stations running through downtown Los Angeles from Union Station to MacArthur Park. Contract A146, Tunnels from 5th/HILL Station to 7th/Flower Station, involves tunnel construction through the heart of downtown Los Angeles. The alignment of the tunnels passes beneath twelve buildings, ranging from a 3-story below grade parking structure to numerous 12 to 14 story buildings. The soil along the alignment is alluvium, consisting of silts and clays, clean sands and gravels located above the ground water table. Because of unstable ground conditions, which led to excessive ground losses in several instances, and because of the potential for excessive building settlements, it became necessary to design and perform a program of chemical grouting. The chemical grouting program was designed such that tunneling could proceed on a one shift per day basis, with chemical grounting being performed on the remaining two shifts. Each day 21,000 to 31,000 liters of sodium silicate grout were injected through sleeveport grout pipes installed 18 m deep through the tunnel face. Tunnel advance rates of 12 m per day, 60 m per week, under full chemical grout cover were achieved. The chemical grouting program virtually eliminated both ground loss and settlement and permitted successful excavation of the tunnels. The purpose of this paper is to describe the chemical grouting program used to control ground losses and settlement on Los Angeles Metro Rail Contract A146. The paper begins with a description of

Jan 1, 1991

By J. Yuan

Ground calcium carbonate (GCC) and chemically precipitated calcium carbonate (PCC) have become important mineral-based commodities in recent years. GCC manufacturing generally requires high purity and high brightness deposits of marble, chalk or limestone as the stone source. PCC usually uses limes made from lesser quality limestone deposits. GCC products have a wide span of particle size, with a d50 size ranging from sub micrometers to as large as several inches such as those used in landscaping. PCC products are typically limited to less than 10 µm (1,250 mesh). Each PCC product has a narrowly distributed size range. GCC and PCC products tend to have higher levels of whiteness com-pared with other traditional filler and extenders, such as kaolin and talc. Published statistics of GCC production volume often vary due to the exclusion of certain size range GCC products. According to Roskill’s latest estimate, world GCC capacity was believed to exceed 56 Mt (62 millionst) during 2004 for all grades.

Jan 1, 2005

By B. J. Arnold

Coal froth flotation cells typically receive little attention in coal preparation plants. They process only a small portion of the total coal feed (perhaps 5-1 0% of the total plant feed in the United States), they are viewed as a way to take the load off the refuse thickener, and their operation is not well-understood by cleaning plant operators. Operating parameters are set based on the equipment supplier information, and reagent dosages are set at the recommendation of the latest chemical vendor. The cells then operate day in and day out, recovering coal and producing a product that may not meet ash or sulfur specifications or that may be the wrong percent solids for downstream dewatering operations. If improvements can be made to this circuit, then the whole plant will benefit. Paying attention to rate and residence time and the wealth of data from the literature or from a series of targeted laboratory tests can give operators the key to improving the performance of froth flotation cells AND overall plant performance. This paper provides an overview of froth flotation rate and residence time data and gives practical suggestions for specifying and using laboratory tests to improve froth flotation performance. Suggestions for improving froth cell performance are also given based on available literature data.

Jan 1, 1999

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

By A. B. Phillips

The Randfontein Estates Gold Mining Company (Witwatersrand) Limited (REGM) operates three metallurgical complexes for the recovery of gold from the Witwatersrand Gold Reefs at the town of Randfontein, 40 kilometers west of Johannesburg. Mining operations in the. area commenced in March 1889 and ceased temporarily in 1965 when the viable ore reserves had been depleted. Exploratory drilling in the 1960's indicated viable deposits of gold in the Elsburg reefs, south of the Witpoortjie Horst Block, _which formed the Southern limit of the previously exploited areas. Three shaft complexes have been established to exploit this area, known as the Cooke secti'on. In 1983 the Doornkop shaft was sunk to the north of the Cooke section to mine Kimberley reef and the South reef.

Jan 1, 1992

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Steven W. Hunt, J. Patrick Powers, Roger C. Ilsley

Artificial groundwater recharge has been used successfully to mitigate water level drawdown in upper alluvial deposits during construction of the Milwaukee deep rock tunnels. Recharge wells in rock as well as soil were used. The effort reduced settlements from consolidation of compressible estuarine deposits, and has minimized damage to existing structures. The paper describes the geology that presented the consolidation problem, and the hydrogeologic conditions that caused the drawdowns. Also presented are the details of recharge well design, construction, operation and performance in an urban environment. The project design calls for grouting and lining of the tunnels to control groundwater in the long term.

Jan 1, 1991

By A. D. Agate

In developing nations, novel mineral processing methods like bacterial leaching are gaining prominence. The principles and practices for isolation and preservation of cultures used in bacterial leaching are discussed with special reference to cultures used in leaching copper from Indian ores. In all, 145 potentially useful microorganisms such as iron- and sulfur-oxidizing bacteria were isolated from various ecosystems of the copper mining areas in the country. The major organisms isolated by enrichment culture technique belonged to T. ferrooxidans and T. thiooxidans species. In addition, thermophilic cultures like Sulfolobus sp. and thermophilic thiobacilli were also isolated. The process of copper leaching was scaled up to the 300-kg level in PVC columns. Since the preservation of efficient cultures in active state was vitally important, a new method was devised that preserved the activity of thiobacilli for a period of more than two years. The novel method of storage in sterile chalcopyrite ore at 8°C can be considered an important advance.

Jan 1, 1987

By Felix E. Mutschler

Alkaline rock-related precious metal deposits include: • orthomagmatic platinum group elements (PGE) ± gold (Au); • porphyry copper-silver-gold (Cu-Ag-Au, ±PGE); • epithermal Au-only, and Au-Ag-base metals; • submarine exhalative Kuroko-, Cyprus-, seamount- and Yellowjacket-type deposits; and • enigmatic deposits akin to Olympic Dam. Coeval epithermal deposits related to porphyry deposits suggest the two types represent separate immiscible fluids evolved in oxidized, CO2-rich alkaline magma chambers. Alkaline rock provinces develop above mantle hot-spots, but crustal structures control the final distribution of magmas and ore fluids. Prospecting guides for alkaline rock-related precious metal deposits include the presence of evolved alkaline rocks, pervasive K-metasomatic, redox and carbonatic alteration and low level Au (±Te, etc.) anomalies. Although alkaline igneous rocks crop out in less than 1 % of the area of the North American Cordillera and craton, alkaline rock-related ore deposits have produced nearly 13% of the total United States and Canadian lode gold production. Large (31-t or 1 million-oz) deposits are common (Fig. 1), and additional deposits and reserves are being discovered. New genetic models are evolving, making alkaline rock-related precious metal prospects attractive exploration targets.

Jan 1, 1991

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023