Search Documents

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By Homer E. Harris

As a result of the enactment of the Federal. Coal Mine Health and Safety Act of 1969 1, the Department of Health, Education, and Welfare (HEW) has been carrying out research in the "field of coal mine health". The National Institute (formerly Bureau) for Occupational Safety and Health (NIOSH) was designated the agency within HEW to be responsible for such research activities. One of the early programs sponsored by NIOSH was undertaken by Eastern Associated Coal Corp., with the Harvard University School of Public Health participating as a subcontractor to Eastern. This program on Coal Mine Respiratory Protective Devices, which started on June 30, 1970, had five major objectives as follows: a. to determine current status of respirator usage with respect to duration and frequency, types. and maintenance b. to determine acceptability ( and reasons therefor) of currently used units c. to determine protection factors provided by respirators worn by working miners d. to make recommendations on ways to improve existing units, or on research needed to develop new types of respiratory protective devices for coal miners e. to provide recommendations to mine management on more effective use of respiratory protective devices

Jan 1, 1973

By Jr. Mason

Eminent Domain is the power of the government or municipality to take property for public use without the consent or acceptance of the owner. Typically the agency taking the property will make an offer on the property, hoping that the owner will immediately accept and allow work to begin. If a mutual resolution regarding the property value cannot be reached, however, the municipality will condemn the premises and institute a condemnation action in a court of law, which is when the problems begin. The power of the government to take the subject property is limited by the Federal and State constitutional duty to pay "just compensation" for the property.

Jan 1, 1989

By A. A. Mular

Examining a typical curriculum for mineral process engineers shows that traditional subjects remain important, namely, engineering, earth and basic sciences, mathematics and mineral proc¬essing technology. However, Table I shows additional subjects that may be woven into a modern curriculum, because of micro- and macro-engineering advances over the years. The ways to incorporate these subjects into the curriculum will vary from school to school. Such changes are in response to evolutionary technological and political needs as determined by society and business. Beginning with the 1950s, engineering empiricism was strengthened through micro-engineering, where fundamentals and mechanism serve as foundations. Scientific apparatus unique to the basic sciences (Zeta meter, FTIR spectroscope) was adapted to test new hypotheses. Coincidentally, as computers became more available, complex differential

Jan 1, 1992

By K. L. Browne

After a decade of high copper prices, major mining companies are renewing their interest in purchasing operating properties and/or developing ore bodies. An existing operation carries with it a history that can present unique opportunities, while a greenfield operation allows for the establishment of a defined culture. Capital investments are distinctly different. A comparison of BHP Copper's Robinson operation, a greenfield property, and BHP Copper's Tintaya operation, a government owned Peruvian property, will provide insights into mining, concentrating and cultural differences between North and South America operations. The Broken Hill Proprietary Co. Ltd. (BHP) is Australia's second-largest company. Fiscal year 1996 sales were US$16 billion, profits were more than US$1 billion and total market capitalization was about US25 billion. In 1885, BHP began mining silver, lead and zinc at Broken Hill, New South Wales, Australia. Throughout its 112-year history, BHP achieved an impressive record of performance and expansion. Today, BHP is one of the world's leading companies (66th on the Standard and Poors 500), having diversified into steel, petroleum and mining with more than 65,000 employees in 70 countries.

Jan 1, 1997

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By Thomas A. Morley

This paper deals with the minimization of ventilation costs for the controlled-flow mine ventilation network. Cost elements considered include the cost of power and the fixed cost of the fans. The problem is modeled in a mixed-integer programming format and solved via the branch and bound method. Computational experience with sample problems is discussed.

Jan 1, 1983

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Stephen G. Whittaker, Rosalind A. Schoof, Martha J. Steele

In determining remedial action objectives for metals in soils, the U.S. Environmental Protection Agency typically assumes that the metal concentrations in house dust are the same as the metal concentrations in soil. Data now available from several studies that were conducted in mining communities suggest that for some metals, concentrations in house dust may be lower than those in soil. This paper reviews available data on the relative soil and indoor dust concentrations of arsenic and cadmium and examines how changing assumptions regarding indoor dust concentrations of arsenic affects risk assessments and determination of cleanup levels.

Jan 1, 1992

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By D. Rumenjak

Fuzzy logic is a useful tool for Sustainable Development (SD) decision making because it can express uncertainty, both in the informational and in the decision-making environment. The general linguistic definition, acceptability for environment (air, water, nature, risk, etc.), as well other aspects of sustainable development (health, management issues, etc) is proved to be useful in approximate reasoning and decision-making. According to this definition, the various fuzzy functions of environmental acceptability can be constructed. This construction is based on the concept of special kinds of fuzzy functions generally defined as Linguistic Variables (LV), which are suitable for mapping to fuzzy sets. Various SD indicators could be used as domains of such functions, expressed either in their physical values (e.g. production, emissions, risk of accidents) or in Measure of Preferences (MP). The most important MP are mentioned below: Stated Preferences Techniques (SPT) of economic evaluation of environment, economic instruments of environmental protection mostly based on Revealed Preference Techniques (RPT), preferences scales (ordinal, cardinal) according to various methods of their construction, etc. Also, the possibility theory (analogous to probability) could be exploited in such construction. It could be used together with environmental engineering modelling formulas for the purpose of determining fuzzy functions. The appropriate forms of linguistic variables, considering limit cases for this purpose, are also discussed.

Jan 1, 2007

By Henry N. McCarl

In the period 1982-1992, world trade has increased in real terms about 65% (Anon., 1992b). The nominal value of this trade in the early 1990s is approximately $5 trillion. In 1970, mineral commodities constituted approximately 20% of the value of world trade. By 1980, despite rising petroleum prices, mineral commodities made up about 18% of the total value of world trade, with crude oil amounting to 16% and other minerals the remaining 2%. By 1987, the major worldwide economic slowdown and falling oil prices meant that minerals constituted only about 10% of the total value of world trade, or about $500 billion in 1987 (Kimbell and Zajac, 1988). The importance of minerals in world trade since 1987 has remained at about these levels. Approximately 40% of world mineral commodity production is traded internationally. Some economists predict that minerals and other commodities are likely to continue to decline in relative importance in terms of the value of world economic output, as well as world trade, into the foreseeable future (Thurow, 1992). This projected decline in commodity demand may also be related to much slower global economic growth over the next decade (Alperovitz, 1992). Industrial minerals and rocks constituted roughly 2.5% of total mineral commodity exports in the late 1980s, but their relative importance as a portion of mineral commodity exports nearly doubled in the decade 1977-1987 (Kimbell and Zajac, 1988). Industrial minerals constitute the most rapidly growing share of total mineral commodity exports. In addition, price declines among industrial minerals were uncommon in the decade 1977-1987 (Kimbell and Zajac, 1988). While prices of sulfur and most of the fertilizer minerals have seen some erosion and slow growth in markets in the period 1987-1992, other industrial minerals have increased in both value and share of the export market (USBM, 1992). The place of industrial minerals in world trade becomes even more significant when one looks at shipments of chemical fertilizers and basic chemicals that are counted as manufactured products rather than industrial mineral commodities. The United States is the major world producer of industrial mineral commodities and products made from these nonmetallic minerals and rocks. The former Soviet Union, now The Commonwealth of Independent States (CIS), and China have very significant deposits of industrial minerals. Japan exports significant quantities of cement. The US, CIS, and Morocco export large amounts of phosphate rock. Canada and Germany export substantial amounts of potash. Sulfur from Poland, industrial diamonds from South Africa, Zaire, and Brazil, and fluorspar from Mexico are all important exports.

Jan 1, 1994

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By H. Haas

European coal mines are facing a very difficult situation. Despite a steadily increasing world energy consumption, the sales of European coal mines have been going down and production has to be adapted. The reason is the collapse of energy prices aided by the decreasing rate of U.S. $ to Deutschmark in the last few years. The problems are not due to the development of European mines themselves. Assured energy supplies are an important condition for the health of a nation's economy. Contribution of domestic energy production ensures some degree of independence from world market fluctuations as to supply volumes and price, and maintaining jobs and should be achieved within the framework of economic constellations. Governmental energy programs are planned towards meeting this end.

Jan 1, 1989

By S. R. Hutchins

Several refractory sulfide and carbonaceous gold ores were examined to determine whether microbial pretreatment could be used to enhance gold recovery. Test samples were biologically leached using unique, thermophilic microorganisms to solubilize iron sulfide minerals. Gold recovery from sulfide ores and concentrates was enhanced following pretreatment with the thermophiles; responses varied widely for the individual materials. Although bioleaching had little effect on the preg robbing characteristics of the carbonaceous gold ores, cyanidation of the bioleached residues yielded higher gold recoveries than cyanidation of the native ore. By combining bioleaching with abiotic processes designed to inhibit preg robbing, gold recoveries of 83-98% were obtained from carbonaceous ores yielding 10-50% gold recovery by direct cyanidation.

Jan 1, 1987

By S. Zendejas-Mendivil, E. Pérez-Segura

The Cananea porphyry copper-deposit is the site of the second largest mining operation in Mexico. Mineralization is related to quartz-monzonite Laramide stocks that intrude volcanic and volcaniclastic Mesozoic rocks. The ore deposit is a stockwork and breccia-pipes system with Cu-Mo sulfides and pervasive quartz-sericite hydrothermal alteration. A study was made of the arsenic distribution in the mine and the ore-dressing plants. The arsenic (As) in the mine is related to a feldspathic quartz-porphyry type rock associated mainly with the breccia pipe structures (100-700 ppm As in the Veta 7 Breccia). There is vertical zoning, with As decreasing in the deepest part of the breccias. This As mineralization corresponds to a later sulfide hydrothermal stage. The concentrates are made of Cu, Fe and Mo sulfides and some minor quantities of As minerals. The most important copper minerals are chalcocite-covellite, bornite and chalcopyrite. Some of these minerals have 390-880 ppm As. The main As mineral is enargite[ [Cu2.97Fe0.06(As0.90 Sb0.01Pb0 01 )0.92 S4 051 and there are traces of stibioluzonite-luzonite I Cu, .95(Aso.4vSbu.49)0.9rfS4.07-Cu2 93(Aso.H4Sba.10)0.94S4.13] and of another stibioluzonite mineral type with substitution of As by Bi[Cu,96(Ascr,,'Sb0ccrB'OJ3jI~6S] These minerals contribute 80% of the As in the concentrates.

Jan 1, 1992

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991