Search Documents

By J. S. Heath

Many disputes related to environmental issues in mining are resolved through often-antagonistic negotiations in a regulatory context or through litigation. These approaches are certainly the best choices for resolving certain disputes. However, just as no single remediation technology is the right fit for every site, so no single dispute resolution process is the best choice for every situation. This paper introduces a range of dispute resolution alternatives (from collaborative decision making through mediation, arbitration, and litigation). Especially when money is tightest, cost-effective dispute resolution(and the outcomes that can accompany it) can have an impact on the bottom line.

Jan 1, 2000

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By Graham G. W. Mustoe, Andrew I. Hustrulid

An advanced numerical model based upon the Discrete Element Method (DEM) has been developed to provide the engineer with unique detailed information to assist in the design of transfer points in large industrial conveyor systems in mining operations. This modeling technique provides a quantitative description of the bulk solids movement through the transfer point. This information consists of the velocity distribution of the bulk solids and the stresses within the bulk solids. The DEM model also gives detailed information concerning the impact forces acting on the transfer structure and the conveyor belts from the bulk solids flow.

Jan 1, 1996

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By R. E. Blair

The economics of the producer-consumer interface - the route from mine to market - impact much more severely on specialty industrial minerals, extender/fillers that have to be sold, than on commodity industrial minerals that are basically supplied. Working capital costs for inventories and accounts receivable, fixed capital costs for storage/ warehousing/distribution, and sales and marketing costs all make the extender/filler producer much more of a marketer than a miner. The future survival of an extender/filler producer will primarily depend on the skill he has in the economics of the interface.

Jan 1, 1981

By D. W. Fohlen, B. A. Filas

The International Finance Corporation (IFC), the private investment arm of the World Bank Group (WBG), requires all IFC-financed projects to comply with its environmental and social policies and guidelines. IFC's review process involves an environmental and social assessment and the implementation of an Environmental Action Plan (EAP) that will set forth the necessary actions to bring the operation into compliance. This paper provides an overview of the environmental and social policies and guidelines that apply to mining projects and examines how WBG/IFC policies and guidelines are applied to mining projects in developing countries. In addition, it includes a review of the increased emphasis IFC is giving to social issues over the past several years based on the existing WBG policies. IFC’s process for the environmental and social review of proposed investments is briefly discussed. The paper focuses on how IFC emphasis has shifted from the traditional environmental and impact mitigation analyses of a few years ago to the integrated social and environmental awareness, action (EAP), and implementation programs (social plans) required today. Today, IFC's focus is to promote sustainable development by investing in projects that directly benefit local communities and the environment. Examples of these changes will be highlighted by a review of recent investments located in West Africa. The goalposts have not moved, but the rules of the game have become tougher.

Jan 1, 2001

By John W. Critchfield

This paper presents an overview of some of the basic issues related to tunnel construction in the presence of flammable and toxic strata gases. Gas properties and possible sources are outlined for the various gases that are commonly encountered underground. Assessment of potential gas hazards prior to construction is discussed. Measures for mitigating the problem during construction are summarized. This RETC Session on Gassy Ground has been organized by the Underground Technology Research Council (UTRC), Technical Committee on Gassy Tunnels.

Jan 1, 1985

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities, and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72 × 10 m3/s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97 × 10 m3/s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16 × 10 m3/s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07 × 10 m3/s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 1, 2024

By P. Somasundaran, H. S. Hanna

The separation of minerals such as apatite and scheelite by flotation from other salt-type minerals such as calcite is extremely complex owing to the close similarity between their physicochemical properties. In this paper, properties relevant to flotation such as crystal structure, solubility, surface charge and adsorption behavior of important salt-type minerals are examined along with the role of inorganic modifying agents such as silicates and polyphosphates and organic modifying agents such as starch and tannin. Flotation characteristics of these minerals are then reviewed and selected separation problems involving salt-type minerals are discussed.

Jan 1, 1976

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By J. P. A. Hortley

In conventional electrolytic copper production, looped copper starter sheets, on which the copper is deposited, are supported by hard-drawn copper bars. These bars have cross-sectional areas of between 1 and 1.4 in2. The suspension bars serve two purposes: firstly to support the cathode, which can weigh up to 150 kg, and secondly to introduce the electric current. IYI examined these two requirements in detail to see whether a better design could be achieved. Considering firstly the current carrying requirement, it wee noted that under normal refinery conditions, each cathode carries between 400 and soak. If one applies the generally accepted rule that 1 in of copper can carry 1000A4 a suspension bar need theoretically contain only 1/2 in2 of copper. This contention is supported by the fact that the 500A current passed through the cathode also appears to pass quite satisfactorily through the two support loops, which have a cross-sectional area of approximately 0.35 in 2. Turning now to the strength requirements, the cross-section of hard-drawn copper bar required to support a 150 kg cathode is relatively small, and easily met by the present designs. It is not, however, the static load applied by the 150 kg cathode immersed in the electrolyte which causes the damage to the hard-drawn copper, or even the increased static load of a 100 kg man standing on one foot in the centre of the bar; the damage is actually caused by the dynamic loads applied to the bare when they are dropped, thrown into containers, lowered too rapidly into the cell, or otherwise mistreated. The important requirement is therefore that the bar does not permanently bend. Its proof stress of limit of proportionality, rather than the amount that it deflects under static loading, should be the strength criterion. With the hard-drawn copper normally used for the manufacture of suspension bars, it has been observed that the copper becomes annealed during use, particularly at the end of the bar where the current is introduced. Thus, after a relatively short time, the cathodes are in effect being supported by annealed copper bars.

Jan 1, 1978

By A. L. Muler

Since 1956, when Broadbent and Callcott 1 proposed to analyze breakage processes by matrix methods, several authors and their co-workers have proposed various models of grinding that, in principle, could lead to fully automated grinding circuits. In particular, Meloy and Gaudin2, Gardner and Austin3, Kelsall and Reid4, Neloy and Bergstrom5, Callcott and Lynch 6, and Draper and Lynch have, by either computer simulation or by experimental data, or by a combination of the two, verified that comminution is reasonably well described by at least two functions: a selection function and a breakage function. The stage concept proposed by Callcott and Lynch6 requires that a classification matrix be included to completely describe breakage in an open circuit rod mill. The purpose of this work, portions of which are herein described, is to accumulate sufficient information on the breakage characteristics of quartz and magnetite in an open circuit rod mill, so that several of the theoretical and experimental approaches proposed in the literature can be compared with each other. Data is being gathered to compare the experimental method used by Kelsall and paid against the stage approach of Callcott and Lynch.

Jan 1, 1968

By Ronald Allum

Arizona leads all other states in the value of gemstones produced with an annual production which exceeds $3,000,000. Gemstones are an important component of the mineral wealth of the State. Turquoise, peridot, chrysocoll a, petrified wood, fire agate and crystallized mineral specimens are among the gemstones commercially mined. Numerous additional deposits are operated by hobbyists. The State's reputation as a source of gemstones and specimens for the collector and lapidary adds to the economy of the State by attracting tourists. Production of gemstones further adds to the State's economy through employment in the value added gemstone processing industries and by employment of Native American craftsmen.

Jan 1, 1988

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985

By Carrie Smith

This fall, the Society for Mining, Metallurgy & Exploration (SME) will begin a new chapter by welcoming its new executive director and chief executive officer (CEO). Melissa Russell, a successful nonprofit executive with more than 30 years of experience in global association management, officially stepped into the role on Sept. 29, 2025. She succeeds longtime CEO Dave Kanagy, CAE, who is retiring in March 2026 after more than two decades of transformative leadership. “I am honored to begin this new chapter with SME and inspired by the vital role this community plays in shaping our world,” said Russell. “I look forward to listening, learning and working alongside this remarkable group of professionals to advance innovation, champion sustainability and create a brilliant future together.” Russell brings a deep portfolio of leadership experience in technical and industrial associations to SME. Most recently, she served as executive director of the Institute of Electrical and Electronics Engineers (IEEE) Computer Society, the largest of the IEEE’s 39 societies, with more than 50,000 members across 150 countries. During her tenure, she strengthened global engagement, advanced financial sustainability and launched strategic humanitarian initiatives.

Oct 1, 2025