Search Documents

By S. Hodgson

Introduction The Red Dog zinc/lead deposit in northwest Alaska is the second largest zinc deposit ever discovered. Being developed by Cominco Alaska, with startup scheduled for early 1990, it will ultimately be the largest zinc mine in the Western World. Table 1 shows the reserves of the deposit. Bob Baker, a local bush pilot, discovered Red Dog in 1968. The US Geological Survey assessed the find. But the Red Dog site had been withdrawn from staking by provisions in the Alaska Native Claims Settlement Act of 1971 (ANCSA). Under the terms of ANCSA, the deposit was selected by the NANA Regional Corporation, one of 13 native corporations established by the Act. Then, in 1980, the US Congress confirmed this selection, in the Alaska National Interest Lands Conservation Act. In 1982, Cominco and NANA reached an agreement that has led to the development of the mine. Under the agreement, Cominco leases the property from NANA, develops and operates the mine, and markets the concentrate produced. In return, NANA receives royalties and, after capital recovery, participates in the net proceeds from the operation. The Alaska State Government is also playing a role in the development of the mine. Under the auspices of the Alaska Industrial Development Authority (AIDA), the state will construct, own, and operate the DeLong Mountains Regional Transportation System. This consists of a 84-km (52¬mile) road from the minesite to the Chukchi Sea. Located here are the port facilities necessary to store and ship the annual concentrate production and receive the mine fuel and supplies. For using this transportation system, Cominco will pay an annual toll fee. Over the anticipated 50 year life of the operation, the fee will provide a 6.5% return to the State of Alaska. In late 1986, Cominco's Board of Directors approved the Red Dog project. And, during the summer of 1987, road construction began. In February 1988, initial stripping began at the ore body and construction started at the millsite. Project setting The project site is approximately 1000 km (600 miles) northwest of Anchorage, 84 km (52 miles) east of tidewater on the Chukchi Sea, and 192 km (120 miles) north of the Arctic Circle (Fig. 1). The countryside consists of low, rolling hills that lead into mountains north and east of the deposit. The vegetation is typical tundra mat. And the site is in an area of permafrost. However, the permafrost is relatively warm and some areas have been found to be thawed. Examples would be creek bottoms and the site of the main waste dump.

Jan 12, 1988

By Steven W. Hunt, Gregory C. Baker, Glen J. Rorison

Microtunneling methods were utilized beneath pile-supported clarifier basins to replace settlement damaged sludge drain lines at the Jones Island Wastewater Treatment Plant in Milwaukee, Wisconsin. To minimize the risk of blockage and expensive recovery of a microtunnel boring machine against pipe piles or construction debris, a Soltau RVS 80 was utilized. This machine allowed the alignment to be initially bored with guided 114-mm diameter rods to ensure proper alignment and lack of obstructions. Casing pipe was then installed by jacking 1-m long, 305-mm diameterclay pipe along the rods and behind an auger head. This case history also discusses how 2.4-m diameter precast concrete pipe was used as a one-pass sinking caisson for workshafts and new cleanout manholes.

Jan 1, 2001

By Faust William A.

At Gold Fields' Chimney Creek Mine, gold ore deliveries to the milling and leaching circuits will come from three separate pits. The challenges in mine scheduling are to combine tonnage flows from these distinct ore bodies to produce a minimum of 4.665 kilogram (150,000 ounces) per year while maintaining a stable workforce and constant mine equipment requirements. A secondary goal is to have the end of milling operations coincide with the completion of leaching of the oxide ore reserves. This paper discusses the techniques used to prepare the long range plan and some of the considerations and practices that will be required for the plan's accomplishment.

Jan 1, 1989

By R. B. Hoy, Stanley J. LeFond, Unni H. Rowell, K. Reckling, Derek G. Fullerton

In 1989 natural industrial diamonds counted for 55% of the world's natural diamond production. Australia is currently the leading producer (35%). Zaire is the second largest producer (19%). of what is primarily industrial grade rather than gem grade. Botswana (17%) is third, with the former USSR (15%) fourth, and the Republic of South Africa (8%) fifth. Diamonds are also mined in Angola, Namibia, the Ivory Coast, the Central African Republic, Ghana, Tanzania, Guinea, and other African countries. In the Western Hemisphere, Brazil is the principal producer, with some production from Venezuela and Guyana [(Fig. 1)]. A very small output of diamonds is mined today in India, which was the first source of commercial production. In the United States, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a pipe there in 1906. Small scale trial mining has not, however, proved economical. Since diamonds were first discovered more than 2,000 years ago, only about 380 t have been mined. In order to obtain 1 g (5 metric carats) of diamonds, it is necessary to remove and process approximately 25 t of rock. Recovering this small percentage involves a combination of highly developed techniques in mining and extremely sophisticated processes in diamond recovery. END USES Diamonds are used for two unrelated end uses: gem diamonds are jewels of great beauty, while industrial diamonds are essential materials of modem industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamonds in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (1.2 to 1.4 mm). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite", General Electric's Compaxa and Stratapax", and Megadiamond's Megapax" have replaced natural diamonds in turning tools, mining and oil drilling bits, and dressing tool applications. Industrial Diamonds The diamond is by far the most important industrial abrasive. As recently as 50 years ago, consumption of industrial diamonds was less than that of gem diamonds, but since that time, industrial use has grown to a position of great dominance. During the six-year period 1929 to 1934, the material produced for industrial use amounted to about 74% by weight of the world's total output of diamonds. In 1989 the percentage of natural industrial diamonds mined in the world was 55%. When synthetic industrial diamonds are added to the natural industrial diamond figures, this percentage becomes 87% of total world diamond production including gems, near gems, industrial, and synthetic stones. The many uses responsible for these significant increases are dependent on the properties of the diamond, including hardness, cleavage, and parting, optical characteristics, presence of sharp points and edges, and capacity for taking and maintaining a high polish. The utilitarian role of the diamond was confined primarily to lapidary products until the industrial revolution, which created the first demand for diamond as an industrial tool. In 1777, a British inventor and instrument maker, Jesse Ramsden, used a diamond to cut a precision screw for an engine that he had invented. The first authentic description of industrial diamonds being set in a saw was recorded in 1854 by a Frenchman, Durnain. Eight years later a Swiss watchmaker, Jean Leschot, developed the first diamond drill bit for use in a hand operated machine, which was employed to drill blastholes in rock. In 1864, diamond bits were put to their severest test up to that time in the construction of the Mont Cenis Tunnel in the Alps. A few years later a steam-powered diamond drill with a speed of 30 rpm was able to penetrate rock at the modest rate of 0.3 m/hr. As the industrial revolution gained momentum on both sides of the Atlantic, metal replaced wood and machines replaced people. Thus the foundation was laid for precision engineering and the recognition of diamonds as an indispensable tool of industry. The next major demand for industrial diamonds came after World War I with the development of cemented carbide cutting tools. Diamond was found to be the most effective medium for finishing and grinding the new ultrahard metal. This discovery rapidly increased the demand for industrial diamonds. The availability of inexpensive diamond material inspired tremendous research into applications. By 1935, the first successful phenol-resin grinding wheel containing diamond had been marketed. Soon afterward, the metal-bonded and vitrified diamond wheels were produced, and, as the matrices and bonds that held the diamond grit in place began to improve, the popularity of diamond grinding wheels grew. The outbreak of World War II, and the accompanying increase in use of hard-metal tools in the munitions industry, increased the demand for industrial diamonds. Since about 1950, the development of ultrahard ceramics, semi- conductor materials, plastics, and exotic metal alloys has further consolidated the diamond's position as an indispensable tool of industry. Only diamond is hard enough to cut these superhard materials with the precision, speed, and economy that industry demands today. Special machines equipped with industrial diamonds are used to remove bumps from concrete runways and highways and to modify highway surfaces in order to prevent skid accidents. Many skids are caused by hydroplaning, a phenomenon that occurs when the roadway is wet. Tires mount a film of water and virtually lose contact with the road surface. Diamond machines cut neat, narrow

Jan 1, 1994

By Photios G. Ioannou, Guillermo F. Salazar, Herbert H. Einstein, Yeong W. Kim

The MIT tunneling group has developed, over the past decade, a number of decision support tools for the geologist and engineer, planner and designer, owner and contractor involved in underground construction. These computer based tools can be used in the planning and exploration stage of a project, in predesign and design, in construction planning and during construction. Tasks as different as optimizing information collection during exploration and during construction, as selecting major design alternatives in predesign and modifying design during construction, as providing cost and time estimation and considering social and physical environmental constraints, can be handled. Output can be in the form desired by the user ranging from geologic profiles (cross sections) to management reports.

Jan 1, 1987

By Y. Ye

Induction times for a variety of minerals have been measured at a particle bed. Electrostatic repulsive forces between bubble and particle generally are of secondary importance in determining the hydrophobic state; nevertheless, the shortest induction times are measured at the isoelectric point of the solid. More importantly, the study shows that the film-rupture mechanism at a polished surface might be different from that at a particle bed. The induction time measured at a particle bed, besides being dependent on the surface chemistry of the system, shows a definite relationship to particle size and density. Theoretical analysis suggests that such a measured induction time at a particle bed should properly be defined as an attachment time which consists of the induction time and the film-displacement time. Thus one portion of the measured attachment time is the induction time, the time required to thin the water film between the particle surface and the gas bubble to a critical thickness so that rupture of the film takes place ('1)' The other portion of the measured attachment time is the time required for the film to be displaced to such an extent that the attachment is stabilized with respect to the upward motion of the bubble and the downward gravitational force acting on the particle ('2)' Further, the present study illustrates that '2 is related to the hydrophobic character of the surface, the rate of film displacement after rupture, the upward velocity of the captive bubble, and, most importantly, the particle size and density.

Jan 1, 1988

By Brent Chamberlain

MARY KORPI: As has been typical today, our next speaker is filling in for one of his co-workers. Scott Lawson will be discussing "The Role of the Supervisor in Mining Operations" written by Brent Chamberlain of Independence Mining Corporation. Scott has more than 25 years in human resources management in the mining industry. He has worked in surface and underground mining environments in both precious and base metal mines. A graduate of Ohio University, Scott is currently manager of human resources at the Independence Mining Company's Cripple Creek and Victor Gold Mining operation located in Victor, Colorado. The only direction that I received from Scott was that he has to leave by 11:45 a.m. as he has a tee-off time with his boss at 1:00 p.m. Thank you to Scott for filling in today.

Jan 1, 1998

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By James L. Whitlock, Amy E. James

During the past twenty years, numerous advances have been made in the technologies used to pretreat sulfidic refractory gold ores. These advances have included improved equipment design, increased gold recoveries, and reduced operating and capital costs. More recently, treatment of refractory gold ores has primarily been accomplished by pressure oxidation (POX), roasting, chlorine oxidation, or biooxidation. In addition to improving the time-proven processes of pressure oxidation and roasting, new and innovative approaches to biooxidation pretreatment of both concentrates and whole ores have been developed. Selecting the appropriate biooxidation technology depends on the nature of the refractoriness in the ore, economic gold recovery, plant design operating parameters (such as desired tonnage), site climatic conditions, and operating and capital costs, as well as several other deciding factors. The objective of this paper is to outline the biooxidation processes and technologies currently available for the recovery of gold from refractory sulfidic ores, to discuss the critical factors that affect plant design and operation, and to provide the metallurgist with a practical guide to choosing the appropriate biooxidation technology for a particular ore or concentrate.

Jan 1, 1999

Gold cyanide equilibrium adsorption isotherms in the loading range typical of operating carbon-in-pulp/carbon-in-leach plants have been established and the effect of various cations and the presence of copper cyanide species quantified. It was found that the equilibrium loading of gold was enhanced by the presence of sodium or calcium, with calcium having an order of magnitude stronger effect. The presence of copper has an adverse effect on the equilibrium loading of gold. A unified model was developed to predict the effect of sodium and calcium concentrations in solution and the competitive carbon adsorption of copper on the equilibrium loading of gold on carbon. A satisfactory agreement between the measured gold equilibrium loadings and the model results was obtained over a wide range of solution conditions.

Jan 1, 2010

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

By Ole Bernt Lile

The well-known method of C. Schlumberger, Mise a la masse, has become a popular method again in ore exploration in Norway after many years of dominance by EM methods. The principle of the method is to place a current electrode within a conducting ore body and remove the other electrode to a great distance. (Figure 1). Often it is convenient to place a return electrode on each side of the area explored. The method is best suited for ores that have a conductivity contrast, relative to the host rock, of several orders of magnitude. The potential drop within the ore itself may then be neglected and the ore contact against the rock may be regarded as an equipotential surface. One may say that the ore body is electrically charged. Therefore, in Norway the method is now most often called the Charged Potential Method (abbreviated CP). The most usual way to present data obtained by CP, is to draw equipotential lines based on potential values measured in profiles on the surface. Such a potential map gives an immediate picture of the outcrop of the ore and also indicates disturbing conductors in the neighborhood. It may also be useful to look at the potential profile and its horizontal gradient along the strike axis of the potential map. These profiles may give information about the strike length of the conductor. Figure 2 shows the theoretical profiles of potential and gradient along the axis of the potential picture on the surface over a charged line plunging 15 degrees. It may be seen that the maximum of the gradient curve clearly indicates the lower end of the conductor. Figure 3 shows the corresponding pro- files over a charged line plunging 45 degrees. In this case, it is not possible to see an indication on the curve of the lower end. Only curve fitting could help interpretation in this case.

Jan 1, 1975

By G. C. Hambleton

There is sufficient indication of the existence of a basic misconception in the Coal Mining industry (on a world-wide basis) as to what computer control really does, what it costs, how it works and how and what it achieves as to make this presentation a welcome opportunity to present the case in what we hope is a simple, meaningful way. A plant cannot be said to be "automated" unless the control system has the capability to react automatically in accordance with predetermined programs under a great multiplicity of operational situations.

Jan 1, 1981

By D. S. Kostick

Soda ash production in the United States during 1994 increased 4%, reaching 9.3 Mt (10.2 million st). That was the second highest production year. Domestic nameplate soda ash capacity is about 11 Mt (12 million st). Overall, the industry operated at about 85% of capacity. Some companies produced at 100% of capacity while others produced at below their design ratings. Although domestic soda ash consumption was slow during the first half of the year, third- and fourth-quarter sales increased, especially in the flat¬glass and fiberglass sectors. These two sectors increased because of greater demand for glass products in the automotive and construction industries. Soda ash sold for pulp caustic soda increased during 1994. This was due to higher prices for and reduced availability of electrolytic caustic soda. It is often preferred for pulp digestion because of its stronger alkalinity.

Jan 1, 1995

By K. Ueda

Lead concentrates from Kuroko (black ore) mines, which contain Cu 4 ? 7%, Pb 55%, Zn 3 - 7%, As 0.5 - 0.9% are treated by hydrometallurgical process in order to smelt the product by electric furnace smelting together with other lead resouces from Kuroko. The hydrometallurgical pretreatment involves sulfuric acid leaching at first stage, ferric leaching at second stage. This paper describes the short history of lead recovery from Kuroko and the performance of laboratory test, pilot plant and commercial operation.

Jan 1, 1982

By Walter C. Labys, William A. Vogely, David O. Wood

INTRODUCTION The past decade has witnessed a literal explosion in formal modeling of energy systems and markets. This rapid development was stimulated primarily by policy issues arising from the energy price shocks of 1973- 1974 and 1979- 1980. The suddenness of this interest is illustrated by comparing the current and earlier editions of Mineral Economics. The third edition, published in 1976, includes an addendum to the section of projection and forecasting methods because, Since the foregoing chapter was written, major events in petroleum have caused an explosion in formal modeling efforts in the energy field.a In contrast, this fourth edition includes the present chapter on energy modeling, and a separate chapter on nonfuel minerals modeling. The considerable interest in formal energy models is based on the complexity of the system, in particular the interaction between technical and engineering data and designs, and economic behavior of energy producers and users. Energy is a vital component in the economic and social well-being of nations, and must increasingly be explicitly considered in developing economic growth and welfare policies. Energy models can contribute to policy development and analysis, both by improved understanding of the energy system, and of the interaction between energy markets and the economy, and as an explicit means of analyzing and comparing the implications of alternative policy actions. At their best, formal models can clarify and illuminate policy options. In this chapter we will survey the objectives, methods, and potential contributions and limitations of energy system modeling. Section 2 considers the objectives, scope, and approaches to energy system and market modeling. Methodological approaches are then discussed more formally in section 3. Our approach is to intro- duce each model type and method via relatively simple generic models, illustrating their use by a selective review of the applications literature. Section 4 shifts the focus from modeling methods to procedures for model evaluation and improving model credibility especially in policy research and analysis. We conclude with some brief remarks on directions and opportunities for future modeling research. ENERGY MODELS: OBJECTIVES, SCOPE AND APPROACHES The concept of a model usually evokes an image of a complex, computerized system of mathematical or econometric equations providing detailed information concerning the operation of the process being modeled. In fact. models may be simple or complex, formal or mental, depending upon the purposes for which the model is intended. Simple judgmental models may be most appropriate when monitoring the overall performance of a process. When more detailed information is required and/or when the model

Jan 1, 1985

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By V. Rajaram

V. Rajaram's paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude's work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 1, 1987

By K. E. Robinson, G. Re, L. Skoski

Introduction A new technology is evolving as a result of growing industry and government concerns over the potential impacts of possible airborne emissions from uranium tailings piles. A major component of the technology is the use of earth covers to stabilize the tailings after mill operations have ceased. While various analytical models have been used to predict the thickness of required covers, experimental validation of the models has been necessary. This paper presents the results of a field program to select and test cover material to determine its suitability for eventual reclamation of a currently active tailings pile. The two main criteria guiding the study were the U.S. Nuclear Regulatory Commission radon flux requirements (reduction to less than twice background pre-1979, and to 2 pCi/m2 -sec above background post-1979) and the desire to employ locally available material. The methodology chosen for this study consisted of three main elements: o Determination of the background radon flux. o Determination of the radon flux from the tailings pile. o Experimental determination of the cover material diffusion coefficient and and calculation of cover thickness. The first two elements of the study are relatively straightforward, the last phase is discussed in detail. Background Radon Flux Measurements of radon-222 emanation rates from the surface of the ground were taken at three sampling locations. Samples were collected by means of the accumulator can method described by Wilkening, 1977. Both morning and afternoon samples were collected at each site to obtain an average. The measured fluxes were fairly uniform and did not differ greatly among sites. The overall average flux for all sites was 0.63[+]0.28(o) pCi/m2 -sec. This value is equal to the average radium-226 concentration determined in the soil, thus yielding a one to one ratio of radon-222 emitted (in pCi/m2 -sec) to soil radium content (in pCi/g). Tailings Pile Radon Flux Two sites on the tailing pile

Jan 1, 1980

By Martin L. Smith, John M. Kemeny

In blasting, an optimal muckpile size distribution can be found in terms of mining and milling productivity and cost. Fragmentation control requires a means of modeling and evaluating blast results. A principle problem in the practical application of empirical blast fragmentation modeling is the evaluation of the muckpile's size distribution. Image analysis of video and photographic records of production size blasts at Cyprus's Miami and Thompson Creek mines is being used to provide data for estimating parameters relating fragmentation to blast design, energy factor and rock quality. The application of image analysis to the estimation of particle size distribution is reviewed with regards to the problem of fragmentation modeling.

Jan 1, 1993