Search Documents

By Andrew L. Mular, Richard R. Klimpel

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off-Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1991

By Y. C. Lo

Grinding process optimization is an exciting new tool for maximizing the performance of existing mineral processing plants. This paper discusses the methodology of optimization which involves plant sampling, pilot tests, modeling, computer simulation and plant verification. The methodology developed emphasizes the interactions among operating variables and design options. Two example applications demonstrate that AG and SAG optimization provides the basis to increase grinding throughput up to 10 percent. This sys- tem optimization technology has been proven to be very cost effective for grinding plant performance improvement.

Jan 1, 1998

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By J. J. Kellar, W. M. Cross, J. D. Miller

Infrared spectroscopy has been one of the most useful experimental techniques for the analysis of surface reactions in flotation systems, including surface alteration and surfactant adsorption reactions. With the advent of Fourier transform infrared (FTIR) spectrometers, many low-energy throughput IR experimental techniques previously unused by flotation researchers have come into greater use. In particular, internal reflection spectroscopy (IRS) is the most often used technique for in-situ studies. To date, three IRS methods have been used for in-situ measurements. These techniques are evaluated for use in characterization of surface reactions in flotation systems. The method using mineral crystals as reactive internal reflection elements (IRE) is of particular interest because it allows surfactant adsorption densities to be calculated directly from in-situ spectral data in real time. Application of in-situ FTIR/IRS with reactive internal reflection elements will be demonstrated for collector adsorption reactions in each of the major flotation systems. The alumina (A1203)/sodium dodecylsulfate system is used as an example for insoluble oxide/silicate flotation, while the fluorite (CaF2)/oleate system serves as a paradigm for semisoluble salt flotation. For sulfide flotation, sphalerite (ZnS) is used as the reactive IRE with potassium amylxanthate and potassium ethylxanthate as collectors. In the case of soluble salt flotation, sylvite (KC1) is used as the IRE with n-octylamine as collector. Finally, the use of reactive IREs in the near-IR spectral region and in spectroelectrochemical research is discussed.

Jan 1, 1989

By Richard Kolada

If the emission of methane into any particular area of an underground coal mine remains constant, then the calculation of ventilation requirements is relatively simple. This is also true if the ventilation system is recirculatory. However, the emission of methane into a working area can vary considerably. There is always a risk that the ventilation will not be able to dilute the emission of methane to acceptable levels, because there are often short-lived peaks of emission which are very large. The ventilation design must therefore consider what is an acceptable level of risks and calculate the airflow requirements to meet this level. The acceptable level of risk can be calculated by examining the historical variation in methane emission into the area to be ventilated. For example, consider that an acceptable level occurs when methane emission peaks only exceed the capability of the ventilation one day in twenty. Then, from the history of methane emission, it is possible to calculate the necessary ventilation requirements. This method has been used since the early 1980s for conventionally ventilated districts. This paper examines the application of this technique to districts ventilated by recirculatory ventilation.

Jan 1, 1987

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By L. A. Puchkov

The paper presents the outline of the results in the algorithms and software of the microprocessor-based system for the powerful drugline bucket automatic motion, as well as the technological process control and functional diagnostics of the electrical equipment. The system is, aimed at the increasing both the draglines' working efficiency and the professional, competence of the operators. The excavator-dragline, equipped by the automatized operation, diagnostic and information processing system, possesses considerable technological: flexibility, which can widen therefore its field of application. The tasks of the dragline bucket motion optimal operation, programming of the excavation and overburden dumping processes, as well as the tasks of the control and the analysis of the technological parameters and the diagnostics of electrical equipment conditions, are defined in the paper. In our paper we present the results of these tasks being solved, providing the algorithms of the main mechanisms for the automatic operation for the swinging bucket controlled motion, the algorithms of the statistical analysis of the working efficiency parameters the algorithms of the diagnostics for electrical driving systems. The algorithms of the motion operation are constructed using the predicting dynamic models. The diagnostic algorithms at the normal working conditions form a number of algebraic invariants always equal to Ø with the accuracy up to when the electrical equipment is parametrically adequate. The algorithms of evaluating and analysis of the excavation efficiency make use of the direct measurement and analytical identification. The working condition and quality of the operation and control algorithms are investigated by simulation and natural testing. The results of the mathematical simulation of the bucket motion (with the 20 m3 capacity) of the excavator-dragline with the boom of 90 m in length are given in the paper.

Jan 1, 1992

By A. Zomosa

In the operation of continuous countercurrent decantation it is well known that an increase in the number of thickeners results in an increase of the fixed costs. But inversely it happens that the variable costs are reduced, i.e. the valuable material has a better recovery. The aim of this paper is to solve the problem by means of an economic balance of both parameters, in order to determine the optimum number of stages.

Jan 1, 1991

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By Markku Virtanen, Pertti Koivistoinen

From the perspective of a large mining company the comminution circuit design is worth keeping within the boundaries of the organisation. The correct circuit design begins from the understanding of the role of grinding. Grinding is a link only in the long "comminution chain," starting from solid rock and ending at the concentrating stage. The final target in comminution is to take a part in the maximization of Net Smelter Return, which goal provides the simultaneous considering of capital costs, operating costs and the economic effect of process results. As a general rule there will be a single crushing stage only, ahead of the grinding process. Grinding does not use any metallic grinding media at all, and there will be fine crushing for critical material in the grinding circuit. Grinding has a minimum two stages, besides, at many concentrators middling products and quite often also tailings are reground.

Jan 1, 1997

By W. Keilich

A methodology of subsidence prediction using the Distinct Element code UDEC has been developed as an alternative for subsidence modelling in the Southern Coalfield, New South Wales, Australia. The models have been validated by comparison with empirical results and observed caving behaviour. At this stage, modelling capability is limited to flat lying terrain. It is planned to apply the methodology to areas of high topographical relief to investigate the mechanics of valley closure.

Jan 1, 2006

By M. Tamlin

The state of the lithium mineral industry is closely linked to the performance of the glass and ceramic industries and to the overall economy. Demand for the glass/ceramic products in Europe, Asia and North America remained strong during 1999. This was due to a slight improvement in the economy during the latter half of the year. Consequently, demand for lithium minerals was firm, with a positive outlook. The major economic minerals for lithium are spodumene, petalite and lepidolite. The latter was once the primary mineral. But its importance hasdeclined since the 1960s. The lithium industry consists of two different segments: •The lithium minerals segment mines from hard-rock deposits and physically processes the material to high-grade concentrates. •The lithium chemicals and metal industry segment. The major feedstock for specialty lithium chemicals was previously high-grade spodumene ore converted to lithium carbonate. However, most lithium carbonate is now sourced from salars in North and South America.

Jan 1, 2000

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By J. T. Winkelmann

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately twenty miles northwest of Kingman, Arizona. The concentrating facility has been regarded, with the expansion in 2011, as a plant capable of treating fifty thousand short tons of feed per day for the mixture of supergene and hypogene ores available. The grinding circuit consists of two 32? x 14? SAG mills and four 20? x 28? ball mills. As ores became harder with greater depth in the adjacent pit areas, however, the SAG mills became severely throughput limited. The traditional treatment for similar properties is the installation of a recycle pebble crushing circuit. Because the cost of such an installation is quite elevated, and preliminary testing and research was inconclusive regarding the predicted throughput increases, management and technical personnel set out to find another solution to the problem. The result entailed a redesign of SAG lifters/liners and a nearly unique circuit change which was, at best, a difficult step that defied current grinding logic. This paper describes these changes, events leading up to them, and the results.

Feb 23, 2014

By Omar A. Muhtadi

6.1 INTRODUCTION The three most critical factors in successful heap leaching operations are: • The methods employed to pretreat ore (i.e, crushing and agglomeration); • Placement of ore on the leach pad (heap building techniques); and • Wetting of the ore with cyanide (solution application techniques). Improper execution of any of these initial steps may result in a substantial sacrifice of total metal extraction or, in the worst case, in project failure. Ore preparation in terms of crushing and agglomeration was discussed in Chapter 5; this chapter therefore focuses on commonly employed techniques for heap construction and solution application. The main objective of heap construction is to obtain the most homogeneous heap possible. "Channeling" of leachate in heaps with preferential seepage paths leads to preferential leachate distribution and uneven/incomplete extraction. The two main contributing causes of channeling are inadequate attention to heap construction and uneven solution application. These pitfall s can best be avoided through a knowledge of the various techniques available and the applicability and success of these techniques with various ore types and site conditions. The remainder of this chapter provides a discussion on these two subjects. 6.2 HEAP BUILDING TECHNIQUES Successful heap building techniques vary with the type of ore and, since no two orebodies are exactly alike, some slight modifications are usually necessary for each specific project. However, it is possible to generalize in terms of the appropriate techniques to be used with ores having similar characteristics. This section discusses the three most commonly used methods of heap construction and provides some guidelines with regard to ore types, construction constraints, and lift height parameters for each of the three. 6.2.1 Run-of-Mine Dumping and Dozing The run-of-mine method of heap building can only be used with ore of a highly silicious nature (i.e., ore which will not generate a large amount of

Jan 1, 1988

By Dinah O. Shumway

California's annual production of >11 million tons of cement, at a value of over $640 million, comes from eight companies, which operate 11 plants. Cement is California's second most important mineral commodity, representing 25% of its total annual mineral production. Although most of the cement produced is consumed within the state, current export locales include the Pacific Northwest, Nevada, Arizona, Utah, and New Mexico. An enumeration of the components required to produce cement is deceptively simple: calcium oxide (65%), silica (20%), alumina (4-5%), iron (3-4%), and calcium sulfate (4%) as a retardant admixture. The last, and most expensive, ingredient in cement manufacture is energy. Detrimental materials in cement mixes include excess .magnesium, alkalis, heavy metals, sulfur, and other volatiles. Each of the 11 cement plants in California requires a unique chemical solution of combined raw materials to produce a uniform product: portland cement. The geologist proposing solutions for the additive raw materials in cement manufacture must have a thorough knowledge of a particular cement plant's needs. In the California cement market, keeping the costs of additive raw materials down is one way to also stay competitive, and using a combination of natural and waste materials as additive raw materials allows cement producers to stay competitive.

Jan 1, 1999

By J. W. Langhans, B. D. Blake

The U. S. Bureau of Mines has been investigating the application of thiosulfate to recover gold directly from low grade refractory carbonaceous ores for the past four years. Statistical experimental methods were used to determine the effects of various leaching parameters on both gold extraction and thiosulfate consumption. Seven variables were investigated, including thiosulfate, copper, ammonia, sulfite, and sulfate concentrations, leaching time, and leaching atmosphere. This information was used in face-centered cubic (FCC) surface response experiments to define the optimum leaching conditions for a low grade ore. Two models were generated from the data to predict gold extraction and thiosulfate consumption as a function of the leaching parameters. The models predicted a gold extraction of 67 pct and reagent consumption of 2 kg [S2032/mt ore at 0.25 M S2032-, 0.0014 M Cu2+, 0.27 M NH,OH, 0.00625 M SO;-,] and leaching for 16 h. Actual tests resulted in 62 pct gold extraction with 0.93 kg S2032- consumed/mt ore. Subsequent column leaching tests have further demonstrated the viability of applying this technology to recover gold from carbonaceous ores without first pretreating the material. Gold extractions in the column tests ranged from 69 to 78 pct with thiosulfate consumption ranging from 0.4 to 5.4 kg/mt ore. These results compare to <5 pct gold extraction using standard cyanide leaching conditions.

Jan 1, 1996

By A. K. Mukhopadhyay

[The mechanical status of a mine ventilation fan can be monitored effectively through vibration analysis. An expert system can be an effective tool in fault diagnosis for a variety of equipment. Computers have made it possible to implement an expert system to analyze the data for correct and appropriate diagnosis. In addition, vibration analysis can provide important information oil the condition of the machine. This paper discusses an approach for an expert system to determine on vibration analysis, practical problems that can occur with a fan. The frequency of the vibration is the only characteristics considered in the analysis, although other variables are discussed in the paper. Finally, a simple computer program, written in Turbo Prolog, is presented. A friendly query system, menu operation and a disk-resident separate knowledge base are a few of the salient features of this system.]

Jan 1, 1997

By M. Z. Rashad

The intersection of joint sets and excavation planes leads to removable blocks which can be expected to fall or slide. The amount and cost of supports required to stabilize these blocks of excavation are related to the number and dimensions of key blocks, the mechanical properties of joints and the active forces present. In this work, the application of the block theory in the study of the kinematics and stability of removable blocks is investigated considering any number of sliding faces for some Egyptian limestone quarries.

Jan 1, 1993