Search Documents

By Gregory Owen Lewis, Wendy Bouwer

Various processing strategies have been implemented in an effort to limit the loss of gold, during leaching, to the naturally-occurring carbonaceous 'preg-robbing' constituents present within certain gold bearing ore sources. Certain processing routes include complex and costly pre­treatment steps to reduce the negative effects of the preg­robber prior to dissolution, while others adopt a simpler direct leach/recovery approach. Process selection is largely dependent upon the gold deportment and the nature of the preg-robbing constituents within the particular ore. In the case of carbonaceous ores in which the bulk of the contained gold is available to direct cyanidation, carbon-in­leach (CIL) technology is generally applied with varying degrees of success. The effectiveness of the CIL route is governed by the competitiveness of the preg-robbing constituents in relation to activated carbon for the preferential adsorption of the solubilized gold. Trials have shown that the DOWEX MINIX strong-base gold-selective ion exchange resin has gold loading characteristics superior to those of activated carbon. The faster gold loading kinetics, together with the higher capacity of this resin, favour its use in an in-leach application as a more effective adsorbent for complex ores. This paper introduces the alternative resin-in-leach (RIL) technology, compares the metallurgical responses to RIL processing of different problematic ore sources, and discusses the interaction between various process conditions. Selected results from laboratory and pilot-scale testwork are presented to highlight the discussion.

Jan 1, 2000

By Rudolf E. Pfister

One of the Swiss transalpine highways includes two remarkable tunnels: the 16.3 km long Gotthard Road Tunnel and the 9.3 km long twin tube Seelisberg Tunnel, both presently under construction. Large diameter shafts up to 900 m long are required for ventilation. Excavation techniques for rock formations ranging from loose sedimentary rock to granite and very hard siliceous limestone were carefully evaluated. The methods finally applied include excavation of shafts in hard rock, conventional drilling and blasting, excavation by ripper-tooth excavator ("Big John") in marlstone, shield protected heading in loose material and soft rock, and tunnel and shaft lining, both by poured concrete and by prefabricated elements. A critical review of the success of these methods can now be made after a five year construction period.

Jan 1, 1976

By T. C. Rao

The quantum of coal fines below 6 mm in run-of-mine (ROM) coal has been increasing due to progressive mechanization of mining methods which has created a substantial incentive, worldwide, to develop suitable fine coal beneficiation techniques. The majority of the efforts have been directed toward reduction in ash/sulfur contents in clean coal. The beneficiation techniques may be broadly grouped as those based on specific gravity and surface property. The processes, which use heavy medium cyclone, water-only cyclone, concentrating tables, and spirals, belong to the former group while the latter group encompasses froth flotation, column flotation, oleo- flotation, and oil agglomeration. In almost all the gravity based techniques, it has been noted that a classification step prior to beneficiation is essential for effective treatment. In general, the effect of design and process variables on the performance of these units and also the quantification of the processes have been the main areas of research and development. In froth flotation, efforts throughout the world have been mainly to understand the effect of variables and to optimize the process. Quantification of the process has been attempted through kinetic studies and mathematical modeling. The efforts have led to the development of new reagents, machine designs, and flowsheets for a specified objective. The attempts so far with the column flotation and oleoflotation processes have indicated a great potential. Extensive R&D efforts are in progress to understand as well as to commercialize the processes. The efforts in the oil agglomeration process have been toward substantiating the inherent merits of the process by developing cheaper bridging liquids and technology to recover and reuse the oil to make the process commercially viable. Modeling of the process has also been attempted to predict the yield and size distribution of the agglomerates. This paper reviews and summarizes the recent developments in the science and technology of fine coal beneficiation processes. The current trends in R%D efforts for these processes are also highlighted.

Jan 1, 1987

By Jouko Suominen

The basic development of various mining equipment has been strongly influenced by two objectives; improving economic results and safety aspects. Both of these factors contribute to increased requirements of mechanization and automation in different parts of mining processes. When we are limiting the discussion the crushing circuits, automation has two dimensions, one being the component automation, or intelligence, the other being automation of complete processes. Both of these subjects are closely tied up, the former being a condition for the latter. The key technologies of crushing automation are transducers, programmable logics and computer software. Also equipment technology continually faces new challenges, which result even in totally new product families. One example of this kind of development area the track-mounted, integrated crushing systems, where design criteria have been simple control, unmanned operation, and flexibility in changing requirements. This crushing system, or philosophy, offers excellent possibilities for new concepts in various underground and open pit applications, connected with automatic process control. Following presentation is a summary of aspects, of haw a crusher manufac¬turer sees the development of automa¬tion as an integral part of equipment technology and development.

Jan 1, 1989

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Colin C. Harris, Jie Zheng, P. Sornasundaran

Powder surface and polymer structural changes during stirred milling have been studied as a function of grinding time, solid concentration and polymer molecular weight. It was found that specific surface area of limestone particles can be increased over 100% by using polymer additives. Particle surface and polymer structure were also found to change during grinding. Powder surface and polymer properties have been determined using Surface Tension, Fluorescence, TOC and HPLC/GPC analysis, and surface and polymer properties are correlated with operating variables and the mechanisms involved are explored. Particularly, the fragmentation of the polymer molecules was found to occur during long term grinding and this was beneficial for ultrafine grinding.

Jan 1, 1998

By Robert J. Whiteley, Colin Parker

Two major tunnel projects with a combined value of about $US700 million have been recently completed in Sydney using both soft ground and hard rock Tunnel Boring Machines. The first of these and the main entry in Australia for the Year 2000 Olympics was the New Southern Railway. This is 10 km of mainly soft ground tunnel linking the Sydney’s International Airport with the Central Business District. The second tunnel was designed to alleviate major stormwater pollution of Sydney Harbour and involved construction of the Northside Storage Tunnel. This is19 km of hard rock tunnel at depths exceeding 90 m that connects many of the northern Sydney suburbs of Sydney with the North Head Ocean Outfall. Case studies of these projects describe the use of innovative geophysical technologies comprising gravity and seismic tomographic imaging with geotechnical testing at the feasibility and design stages. This approach minimised construction and financial risk by effectively quantifying the significant geological and hydrogeological issues along these tunnel routes that exerted major controls on these projects.

Jan 1, 2001

By J. W. Keck

Pilot plant grinding and concentration test results indicate that conglomerate native copper ore can be ground and concentrated using conventional techniques. Single stage autogenous grinding and rod mill-ball mill grinding required the same amount of energy far the required comminution. Metallurgical results were comparable for both types of grinding investigated.

Jan 1, 1973

By C. V. Baltzer, E. L. J. Bingham

Compliance with the EPA's emerging Clean Water Act regulations can be challenging. Open pit copper mines in Arizona have found themselves in a tangled web of changing rules, regulations, and guidance documents regarding storm water and process water discharges. Large mining properties must come up to speed on a myriad of issues including the definition of zero discharge, what constitutes a process related spring or seep, and tailings and waste rock Best Management Practices. The example of the Pinto Valley Mine in Arizona is used to illustrate National Pollution Discharge Elimination System regulatory issues.

Jan 1, 2001

By Ruston A. Ford

This paper reviews the development of the David Bell Mine, from early exploration, through discovery, construction, start-up, underground development, and production. Details are provided regarding the mine development, the mechanized cut and fill stope production, the proposed long-hole stoping with delayed backfilling mining method for the lower levels and the cyanide leach carbon-in- pulp concentrating process. The mine development remains on schedule and under budget with results very much as predicted in the feasibility study.

Jan 1, 1987

By W. J. Pennstrom, J. R. Arnold

Gold Fields installed what was the mining industry's first commercial gold electrowinning/replate circuit at Ortiz in 1981. Its highly successful operation since that time provided the design basis for a similar circuit at Mesquite, which was started in early 1986. These circuits produce plated gold foil suitable for direct shipment to a refinery or melting directly into bars. Detailed descriptions of the electro- winning and replate circuits are given and advantages and disadvantages are discussed.

Jan 1, 1988

By J. R. Sturgul

Computer simulation models of working mines can be of great benefit to the mining engineer. Such models have been used in mine planning (how many trucks/shovels to have, when to add new equipment, etc.), mine design (should a dispatch system be purchased, where is the optimum location for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine and can easily be changed to reflect a wide variety of different situation. Often a major problem for the engineer is how to present the results of the simulation study. Using PROOF(R) animation it is now possible to interface the results of the simulation and project them onto a computer screen in cartoon fashion.

Jan 1, 1993

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Edward Marszalek, Boleslaw Firganek

The paper deals with a computer method and algorithm of optimization of the rescue routes for the endangered staff in the case of fire in a given place of the mine. The adapted method is based on the objective function and realizes the algorithm of the shorest path with weighers assigned to it. The objective function is so defined that it reflects possibly all the hazards and difficulties arising during a fire in the mine. The algorithm is enhanced by an empirical formula for calculation of the smoke zone as result of a mine fire. The presented results of computations of optimal routes for several simple examples using the canonical scheme of the mine network and simulated fires are satisfying and prove the method, the algorithm and the coded program to be correct. The program will be a part of the software library of the mine ventilation engineer. The data for the program will be updated on-line from the fire detection systems.

Jan 1, 1989

By J. A. Herbst

Grinding circuits employed in mineral processing operations are designed to produce feed materials for beneficiation steps such as flotation and magnetic separation, which are sufficiently fine to achieve good liberation of valuable minerals from gangue without over- grinding. In many respects, grinding is the most important unit operation in a mineral processing plant. If adequate liberation is not achieved during grinding, subsequent separation steps will yield low metallurgical recoveries and/or product grades. Grinding energy requirements and operating costs typically exceed 50% of the total expenditures of the entire plant. Because grinding is an inherently energy intensive process and grinding circuit capital and operating costs are high, it is essential that such circuits be run as efficiently as possible. In- creased efficiency in grinding usually translates to a decrease in the energy required to produce a metric ton (short ton) of product size material. It is generally accepted in the mineral industry that efficient grinding circuit performance can not be achieved without the use of some form of automatic control. This is true because all circuits are subject to random disturbances which, if left unchecked, will upset circuit performance and rob a plant of productivity. Such disturbances arise from a variety of sources including natural variations in ore characteristics (particularly hardness changes), uncontrolled water additions, feed-rate upsets, changes in crusher performance, and mechanical upsets such as blockages in pumps and classifiers. Many of these disturbances occur with a frequency which is too high for an operator to detect and react to efficiently. Disturbances which occur on a time scale of several minutes up to several hours can be effectively dealt with using automatic control.

Jan 1, 1979

By Craig Cina

Transporting goods from producers to consumers is a fundamental part of the US economy. The demand for transportation closely reflects the economic health and well-being of the nation's industrial, commercial, and agricultural sectors. The inland waterway barge industry has traditionally played a key role in transporting needed commodities to industries on an economical basis. Barges account for 10% of the domestic intercity tonnage carried by all transportation modes. Water carriers operating on inland waterways hauled more than 450 Mt (500 million st) of cargo in 1980-up from 428 Mt (472 million st) in 1970. Inland Waterway Shipments Metallic and nonmetallic minerals comprise one of the largest commodity groups moved on inland waterways. As illustrated in Table 1, metallic and nonmetallic mineral shipments accounted for more than 69 Mt (77 million st), or nearly 15% of all commodities shipped in 1980. Putting this tonnage in perspective, coal and petroleum represent the two largest commodities moved on inland waterways. In 1980, petroleum and petroleum products accounted for 138 Mt (152 million st), or 28% of all commodities shipped. Similarly, coal represented 120 Mt (132 million st), or 25% or all commodities shipped. Even though shipments of metallic and nonmetallic minerals are smaller than coal and petroleum, they still account for a sizeable portion transported. The inland barge industry moves a variety of metallic and nonmetallic minerals ranging from manganese ores to building cement. Minerals transported by barge include: • iron, copper, bauxite, and manganese ores for metal production; • lime and limestone for construction and electric utility scrubbers; • phosphate rock, natural fertilizers, and gypsum for agricultural needs; • sand, gravel and crushed rock, clay, asphalt, tar, and pitches, and building cement for construction purposes; and • a host of other minerals to meet industrial needs. A few mineral commodities are responsible for a large proportion of waterborne mineral shipments.

Jan 10, 1982

By Wayne W. Murdy

Peru is a mineral hot spot in the world today. Newmont is in the exploratory phase of this mining cycle, a phase full of optimism and expectations. But exploration is high risk. There will be successes but also failures. Many foreign companies will come and go. But it is the responsibility of the mining industry leadership of Peru and the government to continue to foster an environment conducive to investment. This is the time of year companies begin planning their next annual report. Last year, Newmont’s was called “new horizons.” It highlighted the company’s global expansion into Peru, Uzbekistan and Indonesia. Now, projects that were only on the horizon a year ago are moving into production. So “turning opportunity into gold” may be this year’s theme.

Jan 1, 1996

By A. W. Easton

INTRODUCTION This presentation will address changing trade patterns in lead and zinc from the mid 1980's to the early 1990's. Lead and zinc deposits are developed where they are found in many parts of the world. As many are not in major consuming areas, there is significant international trade in both lead and zinc concentrates and in refined metal. Forecasts of mine production have been analyzed, primary and secondary refining capacity and future consumption levels have been estimated, to arrive at the changes in trade patterns expected during the next half decade. This paper will first address concentrate and metal trade patterns for lead, then for zinc, and finally some remarks will be made on captive mine/smelter agreements, on regional trade agreements, and on barriers to trade. I would like to note that. there is only a small international trade in semi-fabricated products such as zinc die-cast alloy, zinc oxide, lead oxide or rolled lead and zinc. Most of the world's zinc and lead trade is in concentrates or refined metal. LEAD TRADE PATTERNS Lead Concentrates Six countries are exporters of lead concentrates. Three countries are in the Americas - Canada, Mexico and Peru, with two in Africa - Morocco and South Africa (including Namibia), and Australia. Due to the limited growth in lead consumption and consequent minimum investment in new production facilities expected, mine and metal production levels and future consumption levels are not forecast to change much between now and 1990. Accordingly, the tonnage of lead concentrates exported will remain essentially unchanged from these six countries. In total they have exports of 480,000 metric tonnes (metal content)* and by 1990 this figure is forecast to rise only slightly with the only increase taking place in Mexico. The concentrates are exported mainly to Western Europe & Japan. Apart from these six main lead concentrate exporting nations, a significant change is expected in the United States. In the mid * All concentrate trade figures are based on metal content

Jan 1, 1986

By W. J. Fotheringham

This paper deals with the mining techniques employed at Canada Tungsten's northern Canadian operations, particularly with respect to their effect on productivity, safety, and stability of relatively large underground openings. The ore body was originally mined commencing in 1974 using conventional pneumatic jumbos in a topslice and horizontal benching room and pillar layout. Pillar stability became an increasing problem as mining progressed, leading to a re-examination and ultimately a conversion of mining method. Rock mechanics considerations and the effect of extraction rate on ground control costs and conditions are analyzed. Other areas discussed concern the results acheived through the use of large diameter I.T.H. drills, radio remote controlled L.H.D. units, and a unique system of hydraulic backfill placement.

Jan 1, 1985